attached to /proc/acpi/hotkey/poll_method, which is dnyamically
created. Please use command "cat /proc/acpi/hotkey/polling_method"
to retrieve it.
+
+Note: Use cmdline "acpi_generic_hotkey" to over-ride
+loading any platform specific drivers.
--- /dev/null
+ S3C24XX USB Host support
+ ========================
+
+
+
+Introduction
+------------
+
+ This document details the S3C2410/S3C2440 in-built OHCI USB host support.
+
+Configuration
+-------------
+
+ Enable at least the following kernel options:
+
+ menuconfig:
+
+ Device Drivers --->
+ USB support --->
+ <*> Support for Host-side USB
+ <*> OHCI HCD support
+
+
+ .config:
+ CONFIG_USB
+ CONFIG_USB_OHCI_HCD
+
+
+ Once these options are configured, the standard set of USB device
+ drivers can be configured and used.
+
+
+Board Support
+-------------
+
+ The driver attaches to a platform device, which will need to be
+ added by the board specific support file in linux/arch/arm/mach-s3c2410,
+ such as mach-bast.c or mach-smdk2410.c
+
+ The platform device's platform_data field is only needed if the
+ board implements extra power control or over-current monitoring.
+
+ The OHCI driver does not ensure the state of the S3C2410's MISCCTRL
+ register, so if both ports are to be used for the host, then it is
+ the board support file's responsibility to ensure that the second
+ port is configured to be connected to the OHCI core.
+
+
+Platform Data
+-------------
+
+ See linux/include/asm-arm/arch-s3c2410/usb-control.h for the
+ descriptions of the platform device data. An implementation
+ can be found in linux/arch/arm/mach-s3c2410/usb-simtec.c .
+
+ The `struct s3c2410_hcd_info` contains a pair of functions
+ that get called to enable over-current detection, and to
+ control the port power status.
+
+ The ports are numbered 0 and 1.
+
+ power_control:
+
+ Called to enable or disable the power on the port.
+
+ enable_oc:
+
+ Called to enable or disable the over-current monitoring.
+ This should claim or release the resources being used to
+ check the power condition on the port, such as an IRQ.
+
+ report_oc:
+
+ The OHCI driver fills this field in for the over-current code
+ to call when there is a change to the over-current state on
+ an port. The ports argument is a bitmask of 1 bit per port,
+ with bit X being 1 for an over-current on port X.
+
+ The function s3c2410_usb_report_oc() has been provided to
+ ensure this is called correctly.
+
+ port[x]:
+
+ This is struct describes each port, 0 or 1. The platform driver
+ should set the flags field of each port to S3C_HCDFLG_USED if
+ the port is enabled.
+
+
+
+Document Author
+---------------
+
+Ben Dooks, (c) 2005 Simtec Electronics
acpi_fake_ecdt [HW,ACPI] Workaround failure due to BIOS lacking ECDT
+ acpi_generic_hotkey [HW,ACPI]
+ Allow consolidated generic hotkey driver to
+ over-ride platform specific driver.
+ See also Documentation/acpi-hotkey.txt.
+
ad1816= [HW,OSS]
Format: <io>,<irq>,<dma>,<dma2>
See also Documentation/sound/oss/AD1816.
in the kernel as they aren't compatible with hotplug or PCI domains or
having sane locking.
-pcibios_present() and Since ages, you don't need to test presence
-pci_present() of PCI subsystem when trying to talk to it.
- If it's not there, the list of PCI devices
- is empty and all functions for searching for
- devices just return NULL.
-pcibios_(read|write)_* Superseded by their pci_(read|write)_*
- counterparts.
-pcibios_find_* Superseded by their pci_get_* counterparts.
-pci_for_each_dev() Superseded by pci_get_device()
-pci_for_each_dev_reverse() Superseded by pci_find_device_reverse()
-pci_for_each_bus() Superseded by pci_find_next_bus()
pci_find_device() Superseded by pci_get_device()
pci_find_subsys() Superseded by pci_get_subsys()
pci_find_slot() Superseded by pci_get_slot()
-pcibios_find_class() Superseded by pci_get_class()
-pci_find_class() Superseded by pci_get_class()
-pci_(read|write)_*_nodev() Superseded by pci_bus_(read|write)_*()
P: LinuxTV.org Project
M: linux-dvb-maintainer@linuxtv.org
L: linux-dvb@linuxtv.org (subscription required)
-W: http://linuxtv.org/developer/dvb.xml
+W: http://linuxtv.org/
S: Supported
EATA-DMA SCSI DRIVER
M: greg@kroah.com
S: Maintained
+PCIE HOTPLUG DRIVER
+P: Kristen Carlson Accardi
+M: kristen.c.accardi@intel.com
+L: pcihpd-discuss@lists.sourceforge.net
+S: Maintained
+
PCMCIA SUBSYSTEM
P: Linux PCMCIA Team
L: http://lists.infradead.org/mailman/listinfo/linux-pcmcia
L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
S: Maintained
+SHPC HOTPLUG DRIVER
+P: Kristen Carlson Accardi
+M: kristen.c.accardi@intel.com
+L: pcihpd-discuss@lists.sourceforge.net
+S: Maintained
+
SPARC (sparc32):
P: William L. Irwin
M: wli@holomorphy.com
ldr r3, [r2, #TI_TP_VALUE]
stmia ip!, {r4 - sl, fp, sp, lr} @ Store most regs on stack
ldr r6, [r2, #TI_CPU_DOMAIN]!
+#if __LINUX_ARM_ARCH__ >= 6
+#ifdef CONFIG_CPU_MPCORE
+ clrex
+#else
+ strex r3, r4, [ip] @ Clear exclusive monitor
+#endif
+#endif
#if defined(CONFIG_CPU_XSCALE) && !defined(CONFIG_IWMMXT)
mra r4, r5, acc0
stmia ip, {r4, r5}
-#if __LINUX_ARM_ARCH__ >= 6
+#include <linux/config.h>
+
+#if __LINUX_ARM_ARCH__ >= 6 && defined(CONFIG_CPU_MPCORE)
.macro bitop, instr
mov r2, #1
and r3, r0, #7 @ Get bit offset
/* linux/arch/arm/mach-s3c2410/usb-simtec.c
*
- * Copyright (c) 2004 Simtec Electronics
+ * Copyright (c) 2004,2005 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* http://www.simtec.co.uk/products/EB2410ITX/
* Modifications:
* 14-Sep-2004 BJD Created
* 18-Oct-2004 BJD Cleanups, and added code to report OC cleared
+ * 09-Aug-2005 BJD Renamed s3c2410_report_oc to s3c2410_usb_report_oc
+ * 09-Aug-2005 BJD Ports powered only if both are enabled
*/
#define DEBUG
* designed boards.
*/
+static unsigned int power_state[2];
+
static void
usb_simtec_powercontrol(int port, int to)
{
pr_debug("usb_simtec_powercontrol(%d,%d)\n", port, to);
- if (port == 1)
- s3c2410_gpio_setpin(S3C2410_GPB4, to ? 0:1);
+ power_state[port] = to;
+
+ if (power_state[0] && power_state[1])
+ s3c2410_gpio_setpin(S3C2410_GPB4, 0);
+ else
+ s3c2410_gpio_setpin(S3C2410_GPB4, 1);
}
static irqreturn_t
if (s3c2410_gpio_getpin(S3C2410_GPG10) == 0) {
pr_debug("usb_simtec: over-current irq (oc detected)\n");
- s3c2410_report_oc(info, 3);
+ s3c2410_usb_report_oc(info, 3);
} else {
pr_debug("usb_simtec: over-current irq (oc cleared)\n");
- s3c2410_report_oc(info, 0);
+ s3c2410_usb_report_oc(info, 0);
}
return IRQ_HANDLED;
{
struct cachepolicy *cp;
unsigned int cr = get_cr();
+ unsigned int user_pgprot;
int cpu_arch = cpu_architecture();
int i;
}
}
+ cp = &cache_policies[cachepolicy];
+ user_pgprot = cp->pte;
+
/*
* ARMv6 and above have extended page tables.
*/
mem_types[MT_MINICLEAN].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE;
mem_types[MT_CACHECLEAN].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE;
+ /*
+ * Mark the device area as "shared device"
+ */
mem_types[MT_DEVICE].prot_pte |= L_PTE_BUFFERABLE;
mem_types[MT_DEVICE].prot_sect |= PMD_SECT_BUFFERED;
- }
- cp = &cache_policies[cachepolicy];
+ /*
+ * User pages need to be mapped with the ASID
+ * (iow, non-global)
+ */
+ user_pgprot |= L_PTE_ASID;
+ }
if (cpu_arch >= CPU_ARCH_ARMv5) {
mem_types[MT_LOW_VECTORS].prot_pte |= cp->pte & PTE_CACHEABLE;
for (i = 0; i < 16; i++) {
unsigned long v = pgprot_val(protection_map[i]);
- v &= (~(PTE_BUFFERABLE|PTE_CACHEABLE)) | cp->pte;
+ v &= (~(PTE_BUFFERABLE|PTE_CACHEABLE)) | user_pgprot;
protection_map[i] = __pgprot(v);
}
mcr p15, 0, r1, c13, c0, 1 @ set context ID
mov pc, lr
-#define nG (1 << 11)
-#define APX (1 << 9)
-#define AP1 (1 << 5)
-#define AP0 (1 << 4)
-#define XN (1 << 0)
-
/*
* cpu_v6_set_pte(ptep, pte)
*
ENTRY(cpu_v6_set_pte)
str r1, [r0], #-2048 @ linux version
- bic r2, r1, #0x00000ff0
+ bic r2, r1, #0x000007f0
bic r2, r2, #0x00000003
- orr r2, r2, #AP0 | 2
+ orr r2, r2, #PTE_EXT_AP0 | 2
tst r1, #L_PTE_WRITE
tstne r1, #L_PTE_DIRTY
- orreq r2, r2, #APX
+ orreq r2, r2, #PTE_EXT_APX
tst r1, #L_PTE_USER
- orrne r2, r2, #AP1 | nG
- tstne r2, #APX
- bicne r2, r2, #APX | AP0
+ orrne r2, r2, #PTE_EXT_AP1
+ tstne r2, #PTE_EXT_APX
+ bicne r2, r2, #PTE_EXT_APX | PTE_EXT_AP0
tst r1, #L_PTE_YOUNG
- biceq r2, r2, #APX | AP1 | AP0
+ biceq r2, r2, #PTE_EXT_APX | PTE_EXT_AP_MASK
@ tst r1, #L_PTE_EXEC
-@ orreq r2, r2, #XN
+@ orreq r2, r2, #PTE_EXT_XN
tst r1, #L_PTE_PRESENT
moveq r2, #0
#endif
/* Attach the domains */
- for_each_online_cpu(i) {
+ for_each_cpu_mask(i, *cpu_map) {
struct sched_domain *sd;
#ifdef CONFIG_SCHED_SMT
sd = &per_cpu(cpu_domains, i);
static int __init nohalt_setup(char * str)
{
- pal_halt = 0;
+ pal_halt = can_do_pal_halt = 0;
return 1;
}
__setup("nohalt", nohalt_setup);
/* The HvReleaseData is the root of the information shared between
* the hypervisor and Linux.
*/
-
-/*
- * WARNING - magic here
- *
- * Ok, this is a horrid hack below, but marginally better than the
- * alternatives. What we really want is just to initialize
- * hvReleaseData in C as in the #if 0 section here. However, gcc
- * refuses to believe that (u32)&x is a constant expression, so will
- * not allow the xMsNucDataOffset field to be properly initialized.
- * So, we declare hvReleaseData in inline asm instead. We use inline
- * asm, rather than a .S file, because the assembler won't generate
- * the necessary relocation for the LparMap either, unless that symbol
- * is declared in the same source file. Finally, we put the asm in a
- * dummy, attribute-used function, instead of at file scope, because
- * file scope asms don't allow contraints. We want to use the "i"
- * constraints to put sizeof() and offsetof() expressions in there,
- * because including asm/offsets.h in C code then stringifying causes
- * all manner of warnings.
- */
-#if 0
struct HvReleaseData hvReleaseData = {
.xDesc = 0xc8a5d9c4, /* "HvRD" ebcdic */
.xSize = sizeof(struct HvReleaseData),
.xVpdAreasPtrOffset = offsetof(struct naca_struct, xItVpdAreas),
.xSlicNacaAddr = &naca, /* 64-bit Naca address */
- .xMsNucDataOffset = (u32)((unsigned long)&xLparMap - KERNELBASE),
+ .xMsNucDataOffset = LPARMAP_PHYS,
.xFlags = HVREL_TAGSINACTIVE /* tags inactive */
/* 64 bit */
/* shared processors */
0xa7, 0x40, 0xf2, 0x4b,
0xf4, 0x4b, 0xf6, 0xf4 },
};
-#endif
-
-
-extern struct HvReleaseData hvReleaseData;
-
-static void __attribute_used__ hvReleaseData_wrapper(void)
-{
- /* This doesn't appear to need any alignment (even 4 byte) */
- asm volatile (
- " lparMapPhys = xLparMap - %3\n"
- " .data\n"
- " .globl hvReleaseData\n"
- "hvReleaseData:\n"
- " .long 0xc8a5d9c4\n" /* xDesc */
- /* "HvRD" in ebcdic */
- " .short %0\n" /* xSize */
- " .short %1\n" /* xVpdAreasPtrOffset */
- " .llong naca\n" /* xSlicNacaAddr */
- " .long lparMapPhys\n" /* xMsNucDataOffset */
- " .long 0\n" /* xRsvd1 */
- " .short %2\n" /* xFlags */
- " .short 4\n" /* xVrmIndex - v5r2m0 */
- " .short 3\n" /* xMinSupportedPlicVrmIndex - v5r1m0 */
- " .short 3\n" /* xMinCompatablePlicVrmIndex - v5r1m0 */
- " .long 0xd38995a4\n" /* xVrmName */
- " .long 0xa740f24b\n" /* "Linux 2.4.64" ebcdic */
- " .long 0xf44bf6f4\n"
- " . = hvReleaseData + %0\n"
- " .previous\n"
- : : "i"(sizeof(hvReleaseData)),
- "i"(offsetof(struct naca_struct, xItVpdAreas)),
- "i"(HVREL_TAGSINACTIVE /* tags inactive, 64 bit, */
- /* shared processors, HMT allowed */
- | 6), /* TEMP: This allows non-GA drivers */
- "i"(KERNELBASE)
- );
-}
-
-struct LparMap __attribute__((aligned (16))) xLparMap = {
- .xNumberEsids = HvEsidsToMap,
- .xNumberRanges = HvRangesToMap,
- .xSegmentTableOffs = STAB0_PAGE,
-
- .xEsids = {
- { .xKernelEsid = GET_ESID(KERNELBASE),
- .xKernelVsid = KERNEL_VSID(KERNELBASE), },
- { .xKernelEsid = GET_ESID(VMALLOCBASE),
- .xKernelVsid = KERNEL_VSID(VMALLOCBASE), },
- },
-
- .xRanges = {
- { .xPages = HvPagesToMap,
- .xOffset = 0,
- .xVPN = KERNEL_VSID(KERNELBASE) << (SID_SHIFT - PAGE_SHIFT),
- },
- },
-};
extern void system_reset_iSeries(void);
extern void machine_check_iSeries(void);
obj-$(CONFIG_KPROBES) += kprobes.o
CFLAGS_ioctl32.o += -Ifs/
+
+ifeq ($(CONFIG_PPC_ISERIES),y)
+arch/ppc64/kernel/head.o: arch/ppc64/kernel/lparmap.s
+AFLAGS_head.o += -Iarch/ppc64/kernel
+endif
#include <asm/cputable.h>
#include <asm/setup.h>
#include <asm/hvcall.h>
+#include <asm/iSeries/LparMap.h>
#ifdef CONFIG_PPC_ISERIES
#define DO_SOFT_DISABLE
.globl fwnmi_data_area
fwnmi_data_area:
+#ifdef CONFIG_PPC_ISERIES
+ . = LPARMAP_PHYS
+#include "lparmap.s"
+#endif /* CONFIG_PPC_ISERIES */
+
/*
* Vectors for the FWNMI option. Share common code.
*/
--- /dev/null
+/*
+ * Copyright (C) 2005 Stephen Rothwell IBM Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <asm/mmu.h>
+#include <asm/page.h>
+#include <asm/iSeries/LparMap.h>
+
+const struct LparMap __attribute__((__section__(".text"))) xLparMap = {
+ .xNumberEsids = HvEsidsToMap,
+ .xNumberRanges = HvRangesToMap,
+ .xSegmentTableOffs = STAB0_PAGE,
+
+ .xEsids = {
+ { .xKernelEsid = GET_ESID(KERNELBASE),
+ .xKernelVsid = KERNEL_VSID(KERNELBASE), },
+ { .xKernelEsid = GET_ESID(VMALLOCBASE),
+ .xKernelVsid = KERNEL_VSID(VMALLOCBASE), },
+ },
+
+ .xRanges = {
+ { .xPages = HvPagesToMap,
+ .xOffset = 0,
+ .xVPN = KERNEL_VSID(KERNELBASE) << (SID_SHIFT - PAGE_SHIFT),
+ },
+ },
+};
if (prom_getprop(u3, "device-rev", &u3_rev, sizeof(u3_rev))
== PROM_ERROR)
return;
- if (u3_rev != 0x35)
+ if (u3_rev != 0x35 && u3_rev != 0x37)
return;
/* does it need fixup ? */
if (prom_getproplen(i2c, "interrupts") > 0)
#include <linux/net.h>
#include <linux/compat.h>
#include <net/compat.h>
+#include <net/sock.h>
#include <asm/uaccess.h>
#include <asm/string.h>
{
struct socket *sock;
char address[MAX_SOCK_ADDR];
- struct iovec iov[UIO_FASTIOV];
+ struct iovec iovstack[UIO_FASTIOV], *iov = iovstack;
unsigned char ctl[sizeof(struct cmsghdr) + 20];
unsigned char *ctl_buf = ctl;
- struct msghdr kern_msg;
- int err, total_len;
+ struct msghdr msg_sys;
+ int err, ctl_len, iov_size, total_len;
- if(msghdr_from_user32_to_kern(&kern_msg, user_msg))
- return -EFAULT;
- if(kern_msg.msg_iovlen > UIO_MAXIOV)
- return -EINVAL;
- err = verify_compat_iovec(&kern_msg, iov, address, VERIFY_READ);
- if (err < 0)
+ err = -EFAULT;
+ if (msghdr_from_user32_to_kern(&msg_sys, user_msg))
+ goto out;
+
+ sock = sockfd_lookup(fd, &err);
+ if (!sock)
goto out;
+
+ /* do not move before msg_sys is valid */
+ err = -EMSGSIZE;
+ if (msg_sys.msg_iovlen > UIO_MAXIOV)
+ goto out_put;
+
+ /* Check whether to allocate the iovec area*/
+ err = -ENOMEM;
+ iov_size = msg_sys.msg_iovlen * sizeof(struct iovec);
+ if (msg_sys.msg_iovlen > UIO_FASTIOV) {
+ iov = sock_kmalloc(sock->sk, iov_size, GFP_KERNEL);
+ if (!iov)
+ goto out_put;
+ }
+
+ err = verify_compat_iovec(&msg_sys, iov, address, VERIFY_READ);
+ if (err < 0)
+ goto out_freeiov;
total_len = err;
- if(kern_msg.msg_controllen) {
- struct sol_cmsghdr __user *ucmsg = kern_msg.msg_control;
+ err = -ENOBUFS;
+ if (msg_sys.msg_controllen > INT_MAX)
+ goto out_freeiov;
+
+ ctl_len = msg_sys.msg_controllen;
+ if (ctl_len) {
+ struct sol_cmsghdr __user *ucmsg = msg_sys.msg_control;
unsigned long *kcmsg;
compat_size_t cmlen;
- if (kern_msg.msg_controllen <= sizeof(compat_size_t))
- return -EINVAL;
+ err = -EINVAL;
+ if (ctl_len <= sizeof(compat_size_t))
+ goto out_freeiov;
- if(kern_msg.msg_controllen > sizeof(ctl)) {
+ if (ctl_len > sizeof(ctl)) {
err = -ENOBUFS;
- ctl_buf = kmalloc(kern_msg.msg_controllen, GFP_KERNEL);
- if(!ctl_buf)
+ ctl_buf = kmalloc(ctl_len, GFP_KERNEL);
+ if (!ctl_buf)
goto out_freeiov;
}
__get_user(cmlen, &ucmsg->cmsg_len);
kcmsg = (unsigned long *) ctl_buf;
*kcmsg++ = (unsigned long)cmlen;
err = -EFAULT;
- if(copy_from_user(kcmsg, &ucmsg->cmsg_level,
- kern_msg.msg_controllen - sizeof(compat_size_t)))
+ if (copy_from_user(kcmsg, &ucmsg->cmsg_level,
+ ctl_len - sizeof(compat_size_t)))
goto out_freectl;
- kern_msg.msg_control = ctl_buf;
+ msg_sys.msg_control = ctl_buf;
}
- kern_msg.msg_flags = solaris_to_linux_msgflags(user_flags);
+ msg_sys.msg_flags = solaris_to_linux_msgflags(user_flags);
- lock_kernel();
- sock = sockfd_lookup(fd, &err);
- if (sock != NULL) {
- if (sock->file->f_flags & O_NONBLOCK)
- kern_msg.msg_flags |= MSG_DONTWAIT;
- err = sock_sendmsg(sock, &kern_msg, total_len);
- sockfd_put(sock);
- }
- unlock_kernel();
+ if (sock->file->f_flags & O_NONBLOCK)
+ msg_sys.msg_flags |= MSG_DONTWAIT;
+ err = sock_sendmsg(sock, &msg_sys, total_len);
out_freectl:
- /* N.B. Use kfree here, as kern_msg.msg_controllen might change? */
- if(ctl_buf != ctl)
- kfree(ctl_buf);
+ if (ctl_buf != ctl)
+ sock_kfree_s(sock->sk, ctl_buf, ctl_len);
out_freeiov:
- if(kern_msg.msg_iov != iov)
- kfree(kern_msg.msg_iov);
-out:
+ if (iov != iovstack)
+ sock_kfree_s(sock->sk, iov, iov_size);
+out_put:
+ sockfd_put(sock);
+out:
return err;
}
asmlinkage int solaris_recvmsg(int fd, struct sol_nmsghdr __user *user_msg, unsigned int user_flags)
{
- struct iovec iovstack[UIO_FASTIOV];
- struct msghdr kern_msg;
- char addr[MAX_SOCK_ADDR];
struct socket *sock;
+ struct iovec iovstack[UIO_FASTIOV];
struct iovec *iov = iovstack;
+ struct msghdr msg_sys;
+ unsigned long cmsg_ptr;
+ int err, iov_size, total_len, len;
+
+ /* kernel mode address */
+ char addr[MAX_SOCK_ADDR];
+
+ /* user mode address pointers */
struct sockaddr __user *uaddr;
int __user *uaddr_len;
- unsigned long cmsg_ptr;
- int err, total_len, len = 0;
- if(msghdr_from_user32_to_kern(&kern_msg, user_msg))
+ if (msghdr_from_user32_to_kern(&msg_sys, user_msg))
return -EFAULT;
- if(kern_msg.msg_iovlen > UIO_MAXIOV)
- return -EINVAL;
- uaddr = kern_msg.msg_name;
+ sock = sockfd_lookup(fd, &err);
+ if (!sock)
+ goto out;
+
+ err = -EMSGSIZE;
+ if (msg_sys.msg_iovlen > UIO_MAXIOV)
+ goto out_put;
+
+ /* Check whether to allocate the iovec area*/
+ err = -ENOMEM;
+ iov_size = msg_sys.msg_iovlen * sizeof(struct iovec);
+ if (msg_sys.msg_iovlen > UIO_FASTIOV) {
+ iov = sock_kmalloc(sock->sk, iov_size, GFP_KERNEL);
+ if (!iov)
+ goto out_put;
+ }
+
+ /*
+ * Save the user-mode address (verify_iovec will change the
+ * kernel msghdr to use the kernel address space)
+ */
+
+ uaddr = (void __user *) msg_sys.msg_name;
uaddr_len = &user_msg->msg_namelen;
- err = verify_compat_iovec(&kern_msg, iov, addr, VERIFY_WRITE);
+ err = verify_compat_iovec(&msg_sys, iov, addr, VERIFY_WRITE);
if (err < 0)
- goto out;
+ goto out_freeiov;
total_len = err;
- cmsg_ptr = (unsigned long) kern_msg.msg_control;
- kern_msg.msg_flags = 0;
+ cmsg_ptr = (unsigned long) msg_sys.msg_control;
+ msg_sys.msg_flags = MSG_CMSG_COMPAT;
- lock_kernel();
- sock = sockfd_lookup(fd, &err);
- if (sock != NULL) {
- if (sock->file->f_flags & O_NONBLOCK)
- user_flags |= MSG_DONTWAIT;
- err = sock_recvmsg(sock, &kern_msg, total_len, user_flags);
- if(err >= 0)
- len = err;
- sockfd_put(sock);
- }
- unlock_kernel();
-
- if(uaddr != NULL && err >= 0)
- err = move_addr_to_user(addr, kern_msg.msg_namelen, uaddr, uaddr_len);
- if(err >= 0) {
- err = __put_user(linux_to_solaris_msgflags(kern_msg.msg_flags), &user_msg->msg_flags);
- if(!err) {
- /* XXX Convert cmsg back into userspace 32-bit format... */
- err = __put_user((unsigned long)kern_msg.msg_control - cmsg_ptr,
- &user_msg->msg_controllen);
- }
+ if (sock->file->f_flags & O_NONBLOCK)
+ user_flags |= MSG_DONTWAIT;
+
+ err = sock_recvmsg(sock, &msg_sys, total_len, user_flags);
+ if(err < 0)
+ goto out_freeiov;
+
+ len = err;
+
+ if (uaddr != NULL) {
+ err = move_addr_to_user(addr, msg_sys.msg_namelen, uaddr, uaddr_len);
+ if (err < 0)
+ goto out_freeiov;
}
+ err = __put_user(linux_to_solaris_msgflags(msg_sys.msg_flags), &user_msg->msg_flags);
+ if (err)
+ goto out_freeiov;
+ err = __put_user((unsigned long)msg_sys.msg_control - cmsg_ptr,
+ &user_msg->msg_controllen);
+ if (err)
+ goto out_freeiov;
+ err = len;
- if(kern_msg.msg_iov != iov)
- kfree(kern_msg.msg_iov);
+out_freeiov:
+ if (iov != iovstack)
+ sock_kfree_s(sock->sk, iov, iov_size);
+out_put:
+ sockfd_put(sock);
out:
- if(err < 0)
- return err;
- return len;
+ return err;
}
{
if (notscsync || !cpu_has_tsc)
return;
- sync_tsc(boot_cpu_id);
+ sync_tsc(0);
}
static __init int notscsync_setup(char *s)
*/
#define IS_RESERVED_ADDR(base, len) \
(((len) > 0) && ((base) > 0) && ((base) + (len) < IO_SPACE_LIMIT) \
- && ((base) + (len) > 0x1000))
+ && ((base) + (len) > PCIBIOS_MIN_IO))
/*
* Clearing the flag (IORESOURCE_BUSY) allows drivers to use
extern char line_buf[80];
#endif /*ENABLE_DEBUGGER*/
-int acpi_specific_hotkey_enabled;
+int acpi_specific_hotkey_enabled = TRUE;
EXPORT_SYMBOL(acpi_specific_hotkey_enabled);
static unsigned int acpi_irq_irq;
int __init
acpi_hotkey_setup(char *str)
{
- acpi_specific_hotkey_enabled = TRUE;
+ acpi_specific_hotkey_enabled = FALSE;
return 1;
}
-__setup("acpi_specific_hotkey", acpi_hotkey_setup);
+__setup("acpi_generic_hotkey", acpi_hotkey_setup);
/*
* max_cstate is defined in the base kernel so modules can
pr_debug("device class '%s': release.\n", cd->class_id);
+ if (cd->devt_attr) {
+ kfree(cd->devt_attr);
+ cd->devt_attr = NULL;
+ }
+
if (cls->release)
cls->release(cd);
else {
if (class_dev->dev)
sysfs_remove_link(&class_dev->kobj, "device");
- if (class_dev->devt_attr) {
+ if (class_dev->devt_attr)
class_device_remove_file(class_dev, class_dev->devt_attr);
- kfree(class_dev->devt_attr);
- class_dev->devt_attr = NULL;
- }
class_device_remove_attrs(class_dev);
kobject_hotplug(&class_dev->kobj, KOBJ_REMOVE);
static int mmap_kmem(struct file * file, struct vm_area_struct * vma)
{
- unsigned long long val;
+ unsigned long pfn;
+
+ /* Turn a kernel-virtual address into a physical page frame */
+ pfn = __pa((u64)vma->vm_pgoff << PAGE_SHIFT) >> PAGE_SHIFT;
+
/*
* RED-PEN: on some architectures there is more mapped memory
* than available in mem_map which pfn_valid checks
*
* RED-PEN: vmalloc is not supported right now.
*/
- if (!pfn_valid(vma->vm_pgoff))
+ if (!pfn_valid(pfn))
return -EIO;
- val = (u64)vma->vm_pgoff << PAGE_SHIFT;
- vma->vm_pgoff = __pa(val) >> PAGE_SHIFT;
+
+ vma->vm_pgoff = pfn;
return mmap_mem(file, vma);
}
/*
- * i8xx_tco 0.07: TCO timer driver for i8xx chipsets
+ * i8xx_tco: TCO timer driver for i8xx chipsets
*
* (c) Copyright 2000 kernel concepts <nils@kernelconcepts.de>, All Rights Reserved.
* http://www.kernelconcepts.de
* 20050128 Wim Van Sebroeck <wim@iguana.be>
* 0.07 Added support for the ICH4-M, ICH6, ICH6R, ICH6-M, ICH6W and ICH6RW
* chipsets. Also added support for the "undocumented" ICH7 chipset.
+ * 20050807 Wim Van Sebroeck <wim@iguana.be>
+ * 0.08 Make sure that the watchdog is only "armed" when started.
+ * (Kernel Bug 4251)
*/
/*
#include "i8xx_tco.h"
/* Module and version information */
-#define TCO_VERSION "0.07"
+#define TCO_VERSION "0.08"
#define TCO_MODULE_NAME "i8xx TCO timer"
#define TCO_DRIVER_NAME TCO_MODULE_NAME ", v" TCO_VERSION
#define PFX TCO_MODULE_NAME ": "
unsigned char val;
spin_lock(&tco_lock);
+
+ /* disable chipset's NO_REBOOT bit */
+ pci_read_config_byte (i8xx_tco_pci, 0xd4, &val);
+ val &= 0xfd;
+ pci_write_config_byte (i8xx_tco_pci, 0xd4, val);
+
+ /* Bit 11: TCO Timer Halt -> 0 = The TCO timer is enabled to count */
val = inb (TCO1_CNT + 1);
val &= 0xf7;
outb (val, TCO1_CNT + 1);
val = inb (TCO1_CNT + 1);
+
spin_unlock(&tco_lock);
if (val & 0x08)
static int tco_timer_stop (void)
{
- unsigned char val;
+ unsigned char val, val1;
spin_lock(&tco_lock);
+ /* Bit 11: TCO Timer Halt -> 1 = The TCO timer is disabled */
val = inb (TCO1_CNT + 1);
val |= 0x08;
outb (val, TCO1_CNT + 1);
val = inb (TCO1_CNT + 1);
+
+ /* Set the NO_REBOOT bit to prevent later reboots, just for sure */
+ pci_read_config_byte (i8xx_tco_pci, 0xd4, &val1);
+ val1 |= 0x02;
+ pci_write_config_byte (i8xx_tco_pci, 0xd4, val1);
+
spin_unlock(&tco_lock);
if ((val & 0x08) == 0)
static int tco_timer_keepalive (void)
{
spin_lock(&tco_lock);
+ /* Reload the timer by writing to the TCO Timer Reload register */
outb (0x01, TCO1_RLD);
spin_unlock(&tco_lock);
return 0;
printk (KERN_ERR PFX "failed to get TCOBASE address\n");
return 0;
}
- /*
- * Check chipset's NO_REBOOT bit
- */
+
+ /* Check chipset's NO_REBOOT bit */
pci_read_config_byte (i8xx_tco_pci, 0xd4, &val1);
if (val1 & 0x02) {
val1 &= 0xfd;
return 0; /* Cannot reset NO_REBOOT bit */
}
}
+ /* Disable reboots untill the watchdog starts */
+ val1 |= 0x02;
+ pci_write_config_byte (i8xx_tco_pci, 0xd4, val1);
+
/* Set the TCO_EN bit in SMI_EN register */
if (!request_region (SMI_EN + 1, 1, "i8xx TCO")) {
printk (KERN_ERR PFX "I/O address 0x%04x already in use\n",
static void __exit watchdog_cleanup (void)
{
- u8 val;
-
/* Stop the timer before we leave */
if (!nowayout)
tco_timer_stop ();
- /* Set the NO_REBOOT bit to prevent later reboots, just for sure */
- pci_read_config_byte (i8xx_tco_pci, 0xd4, &val);
- val |= 0x02;
- pci_write_config_byte (i8xx_tco_pci, 0xd4, val);
-
/* Deregister */
misc_deregister (&i8xx_tco_miscdev);
unregister_reboot_notifier(&i8xx_tco_notifier);
#include <asm/sibyte/sb1250_smbus.h>
static struct i2c_algo_sibyte_data sibyte_board_data[2] = {
- { NULL, 0, (void *) (KSEG1+A_SMB_BASE(0)) },
- { NULL, 1, (void *) (KSEG1+A_SMB_BASE(1)) }
+ { NULL, 0, (void *) (CKSEG1+A_SMB_BASE(0)) },
+ { NULL, 1, (void *) (CKSEG1+A_SMB_BASE(1)) }
};
static struct i2c_adapter sibyte_board_adapter[2] = {
goto failed;
g = alloc_disk_node(1 << PARTN_BITS,
- pcibus_to_node(drive->hwif->pci_dev->bus));
+ hwif_to_node(drive->hwif));
if (!g)
goto out_free_idkp;
}
#endif /* MAX_HWIFS > 1 */
-static inline int hwif_to_node(ide_hwif_t *hwif)
-{
- if (hwif->pci_dev)
- return pcibus_to_node(hwif->pci_dev->bus);
- else
- /* Add ways to determine the node of other busses here */
- return -1;
-}
-
/*
* init request queue
*/
static void __exit ns558_exit(void)
{
- struct ns558 *ns558;
+ struct ns558 *ns558, *safe;
- list_for_each_entry(ns558, &ns558_list, node) {
+ list_for_each_entry_safe(ns558, safe, &ns558_list, node) {
gameport_unregister_port(ns558->gameport);
release_region(ns558->io & ~(ns558->size - 1), ns558->size);
kfree(ns558);
support this frontend.
config DVB_LGDT330X
- tristate "LGDT3302 or LGDT3303 based (DViCO FusionHDTV Gold)"
+ tristate "LG Electronics LGDT3302/LGDT3303 based"
depends on DVB_CORE
help
An ATSC 8VSB and QAM64/256 tuner module. Say Y when you want
}
}
-#ifdef MUTE_TDA9887
-static int i2c_write_ntsc_demod (struct lgdt330x_state* state, u8 buf[2])
-{
- struct i2c_msg msg =
- { .addr = 0x43,
- .flags = 0,
- .buf = buf,
- .len = 2 };
- int err;
-
- if ((err = i2c_transfer(state->i2c, &msg, 1)) != 1) {
- printk(KERN_WARNING "lgdt330x: %s error (addr %02x <- %02x, err = %i)\n", __FUNCTION__, msg.buf[0], msg.buf[1], err);
- if (err < 0)
- return err;
- else
- return -EREMOTEIO;
- }
- return 0;
-}
-
-static void fiddle_with_ntsc_if_demod(struct lgdt330x_state* state)
-{
- // Experimental code
- u8 buf0[] = {0x00, 0x20};
- u8 buf1[] = {0x01, 0x00};
- u8 buf2[] = {0x02, 0x00};
-
- i2c_write_ntsc_demod(state, buf0);
- i2c_write_ntsc_demod(state, buf1);
- i2c_write_ntsc_demod(state, buf2);
-}
-#endif
static int lgdt330x_init(struct dvb_frontend* fe)
{
chip_name = "LGDT3303";
err = i2c_write_demod_bytes(state, lgdt3303_init_data,
sizeof(lgdt3303_init_data));
-#ifdef MUTE_TDA9887
- fiddle_with_ntsc_if_demod(state);
-#endif
break;
default:
chip_name = "undefined";
static struct dvb_frontend_ops lgdt3302_ops = {
.info = {
- .name= "LG Electronics LGDT3302/LGDT3303 VSB/QAM Frontend",
+ .name= "LG Electronics LGDT3302 VSB/QAM Frontend",
.type = FE_ATSC,
.frequency_min= 54000000,
.frequency_max= 858000000,
To compile this support as a module, choose M here: the
module will be called i2o_config.
+ Note: If you want to use the new API you have to download the
+ i2o_config patch from http://i2o.shadowconnect.com/
+
config I2O_CONFIG_OLD_IOCTL
bool "Enable ioctls (OBSOLETE)"
depends on I2O_CONFIG
static struct i2o_driver i2o_config_driver;
-/* Special file operations for sysfs */
-struct fops_attribute {
- struct bin_attribute bin;
- struct file_operations fops;
-};
-
-/**
- * sysfs_read_dummy
- */
-static ssize_t sysfs_read_dummy(struct kobject *kobj, char *buf, loff_t offset,
- size_t count)
-{
- return 0;
-};
-
-/**
- * sysfs_write_dummy
- */
-static ssize_t sysfs_write_dummy(struct kobject *kobj, char *buf, loff_t offset,
- size_t count)
-{
- return 0;
-};
-
-/**
- * sysfs_create_fops_file - Creates attribute with special file operations
- * @kobj: kobject which should contains the attribute
- * @attr: attributes which should be used to create file
- *
- * First creates attribute @attr in kobject @kobj. If it is the first time
- * this function is called, merge old fops from sysfs with new one and
- * write it back. Afterwords the new fops will be set for the created
- * attribute.
- *
- * Returns 0 on success or negative error code on failure.
- */
-static int sysfs_create_fops_file(struct kobject *kobj,
- struct fops_attribute *attr)
-{
- struct file_operations tmp, *fops;
- struct dentry *d;
- struct qstr qstr;
- int rc;
-
- fops = &attr->fops;
-
- if (fops->read)
- attr->bin.read = sysfs_read_dummy;
-
- if (fops->write)
- attr->bin.write = sysfs_write_dummy;
-
- if ((rc = sysfs_create_bin_file(kobj, &attr->bin)))
- return rc;
-
- qstr.name = attr->bin.attr.name;
- qstr.len = strlen(qstr.name);
- qstr.hash = full_name_hash(qstr.name, qstr.len);
-
- if ((d = lookup_hash(&qstr, kobj->dentry))) {
- if (!fops->owner) {
- memcpy(&tmp, d->d_inode->i_fop, sizeof(tmp));
- if (fops->read)
- tmp.read = fops->read;
- if (fops->write)
- tmp.write = fops->write;
- memcpy(fops, &tmp, sizeof(tmp));
- }
-
- d->d_inode->i_fop = fops;
- } else
- sysfs_remove_bin_file(kobj, &attr->bin);
-
- return -ENOENT;
-};
-
-/**
- * sysfs_remove_fops_file - Remove attribute with special file operations
- * @kobj: kobject which contains the attribute
- * @attr: attributes which are used to create file
- *
- * Only wrapper arround sysfs_remove_bin_file()
- *
- * Returns 0 on success or negative error code on failure.
- */
-static inline int sysfs_remove_fops_file(struct kobject *kobj,
- struct fops_attribute *attr)
-{
- return sysfs_remove_bin_file(kobj, &attr->bin);
-};
-
-/**
- * i2o_config_read_hrt - Returns the HRT of the controller
- * @kob: kernel object handle
- * @buf: buffer into which the HRT should be copied
- * @off: file offset
- * @count: number of bytes to read
- *
- * Put @count bytes starting at @off into @buf from the HRT of the I2O
- * controller corresponding to @kobj.
- *
- * Returns number of bytes copied into buffer.
- */
-static ssize_t i2o_config_read_hrt(struct kobject *kobj, char *buf,
- loff_t offset, size_t count)
-{
- struct i2o_controller *c = kobj_to_i2o_device(kobj)->iop;
- i2o_hrt *hrt = c->hrt.virt;
-
- u32 size = (hrt->num_entries * hrt->entry_len + 2) * 4;
-
- if (offset > size)
- return 0;
-
- if (offset + count > size)
- count = size - offset;
-
- memcpy(buf, (u8 *) hrt + offset, count);
-
- return count;
-};
-
-/**
- * i2o_config_read_lct - Returns the LCT of the controller
- * @kob: kernel object handle
- * @buf: buffer into which the LCT should be copied
- * @off: file offset
- * @count: number of bytes to read
- *
- * Put @count bytes starting at @off into @buf from the LCT of the I2O
- * controller corresponding to @kobj.
- *
- * Returns number of bytes copied into buffer.
- */
-static ssize_t i2o_config_read_lct(struct kobject *kobj, char *buf,
- loff_t offset, size_t count)
-{
- struct i2o_controller *c = kobj_to_i2o_device(kobj)->iop;
- u32 size = c->lct->table_size * 4;
-
- if (offset > size)
- return 0;
-
- if (offset + count > size)
- count = size - offset;
-
- memcpy(buf, (u8 *) c->lct + offset, count);
-
- return count;
-};
-
-#define I2O_CONFIG_SW_ATTR(_name,_mode,_type,_swid) \
-static ssize_t i2o_config_##_name##_read(struct file *file, char __user *buf, size_t count, loff_t * offset) { \
- return i2o_config_sw_read(file, buf, count, offset, _type, _swid); \
-};\
-\
-static ssize_t i2o_config_##_name##_write(struct file *file, const char __user *buf, size_t count, loff_t * offset) { \
- return i2o_config_sw_write(file, buf, count, offset, _type, _swid); \
-}; \
-\
-static struct fops_attribute i2o_config_attr_##_name = { \
- .bin = { .attr = { .name = __stringify(_name), .mode = _mode, \
- .owner = THIS_MODULE }, \
- .size = 0, }, \
- .fops = { .write = i2o_config_##_name##_write, \
- .read = i2o_config_##_name##_read} \
-};
-
-#ifdef CONFIG_I2O_EXT_ADAPTEC
-
-/**
- * i2o_config_dpt_reagion - Converts type and id to flash region
- * @swtype: type of software module reading
- * @swid: id of software which should be read
- *
- * Converts type and id from I2O spec to the matching region for DPT /
- * Adaptec controllers.
- *
- * Returns region which match type and id or -1 on error.
- */
-static u32 i2o_config_dpt_region(u8 swtype, u8 swid)
-{
- switch (swtype) {
- case I2O_SOFTWARE_MODULE_IRTOS:
- /*
- * content: operation firmware
- * region size:
- * 0xbc000 for 2554, 3754, 2564, 3757
- * 0x170000 for 2865
- * 0x17c000 for 3966
- */
- if (!swid)
- return 0;
-
- break;
-
- case I2O_SOFTWARE_MODULE_IOP_PRIVATE:
- /*
- * content: BIOS and SMOR
- * BIOS size: first 0x8000 bytes
- * region size:
- * 0x40000 for 2554, 3754, 2564, 3757
- * 0x80000 for 2865, 3966
- */
- if (!swid)
- return 1;
-
- break;
-
- case I2O_SOFTWARE_MODULE_IOP_CONFIG:
- switch (swid) {
- case 0:
- /*
- * content: NVRAM defaults
- * region size: 0x2000 bytes
- */
- return 2;
- case 1:
- /*
- * content: serial number
- * region size: 0x2000 bytes
- */
- return 3;
- }
- break;
- }
-
- return -1;
-};
-
-#endif
-
-/**
- * i2o_config_sw_read - Read a software module from controller
- * @file: file pointer
- * @buf: buffer into which the data should be copied
- * @count: number of bytes to read
- * @off: file offset
- * @swtype: type of software module reading
- * @swid: id of software which should be read
- *
- * Transfers @count bytes at offset @offset from IOP into buffer using
- * type @swtype and id @swid as described in I2O spec.
- *
- * Returns number of bytes copied into buffer or error code on failure.
- */
-static ssize_t i2o_config_sw_read(struct file *file, char __user * buf,
- size_t count, loff_t * offset, u8 swtype,
- u32 swid)
-{
- struct sysfs_dirent *sd = file->f_dentry->d_parent->d_fsdata;
- struct kobject *kobj = sd->s_element;
- struct i2o_controller *c = kobj_to_i2o_device(kobj)->iop;
- u32 m, function = I2O_CMD_SW_UPLOAD;
- struct i2o_dma buffer;
- struct i2o_message __iomem *msg;
- u32 __iomem *mptr;
- int rc, status;
-
- m = i2o_msg_get_wait(c, &msg, I2O_TIMEOUT_MESSAGE_GET);
- if (m == I2O_QUEUE_EMPTY)
- return -EBUSY;
-
- mptr = &msg->body[3];
-
- if ((rc = i2o_dma_alloc(&c->pdev->dev, &buffer, count, GFP_KERNEL))) {
- i2o_msg_nop(c, m);
- return rc;
- }
-#ifdef CONFIG_I2O_EXT_ADAPTEC
- if (c->adaptec) {
- mptr = &msg->body[4];
- function = I2O_CMD_PRIVATE;
-
- writel(TEN_WORD_MSG_SIZE | SGL_OFFSET_8, &msg->u.head[0]);
-
- writel(I2O_VENDOR_DPT << 16 | I2O_DPT_FLASH_READ,
- &msg->body[0]);
- writel(i2o_config_dpt_region(swtype, swid), &msg->body[1]);
- writel(*offset, &msg->body[2]);
- writel(count, &msg->body[3]);
- } else
-#endif
- writel(NINE_WORD_MSG_SIZE | SGL_OFFSET_7, &msg->u.head[0]);
-
- writel(0xD0000000 | count, mptr++);
- writel(buffer.phys, mptr);
-
- writel(function << 24 | HOST_TID << 12 | ADAPTER_TID, &msg->u.head[1]);
- writel(i2o_config_driver.context, &msg->u.head[2]);
- writel(0, &msg->u.head[3]);
-
-#ifdef CONFIG_I2O_EXT_ADAPTEC
- if (!c->adaptec)
-#endif
- {
- writel((u32) swtype << 16 | (u32) 1 << 8, &msg->body[0]);
- writel(0, &msg->body[1]);
- writel(swid, &msg->body[2]);
- }
-
- status = i2o_msg_post_wait_mem(c, m, 60, &buffer);
-
- if (status == I2O_POST_WAIT_OK) {
- if (!(rc = copy_to_user(buf, buffer.virt, count))) {
- rc = count;
- *offset += count;
- }
- } else
- rc = -EIO;
-
- if (status != -ETIMEDOUT)
- i2o_dma_free(&c->pdev->dev, &buffer);
-
- return rc;
-};
-
-/**
- * i2o_config_sw_write - Write a software module to controller
- * @file: file pointer
- * @buf: buffer into which the data should be copied
- * @count: number of bytes to read
- * @off: file offset
- * @swtype: type of software module writing
- * @swid: id of software which should be written
- *
- * Transfers @count bytes at offset @offset from buffer to IOP using
- * type @swtype and id @swid as described in I2O spec.
- *
- * Returns number of bytes copied from buffer or error code on failure.
- */
-static ssize_t i2o_config_sw_write(struct file *file, const char __user * buf,
- size_t count, loff_t * offset, u8 swtype,
- u32 swid)
-{
- struct sysfs_dirent *sd = file->f_dentry->d_parent->d_fsdata;
- struct kobject *kobj = sd->s_element;
- struct i2o_controller *c = kobj_to_i2o_device(kobj)->iop;
- u32 m, function = I2O_CMD_SW_DOWNLOAD;
- struct i2o_dma buffer;
- struct i2o_message __iomem *msg;
- u32 __iomem *mptr;
- int rc, status;
-
- m = i2o_msg_get_wait(c, &msg, I2O_TIMEOUT_MESSAGE_GET);
- if (m == I2O_QUEUE_EMPTY)
- return -EBUSY;
-
- mptr = &msg->body[3];
-
- if ((rc = i2o_dma_alloc(&c->pdev->dev, &buffer, count, GFP_KERNEL)))
- goto nop_msg;
-
- if ((rc = copy_from_user(buffer.virt, buf, count)))
- goto free_buffer;
-
-#ifdef CONFIG_I2O_EXT_ADAPTEC
- if (c->adaptec) {
- mptr = &msg->body[4];
- function = I2O_CMD_PRIVATE;
-
- writel(TEN_WORD_MSG_SIZE | SGL_OFFSET_8, &msg->u.head[0]);
-
- writel(I2O_VENDOR_DPT << 16 | I2O_DPT_FLASH_WRITE,
- &msg->body[0]);
- writel(i2o_config_dpt_region(swtype, swid), &msg->body[1]);
- writel(*offset, &msg->body[2]);
- writel(count, &msg->body[3]);
- } else
-#endif
- writel(NINE_WORD_MSG_SIZE | SGL_OFFSET_7, &msg->u.head[0]);
-
- writel(0xD4000000 | count, mptr++);
- writel(buffer.phys, mptr);
-
- writel(function << 24 | HOST_TID << 12 | ADAPTER_TID, &msg->u.head[1]);
- writel(i2o_config_driver.context, &msg->u.head[2]);
- writel(0, &msg->u.head[3]);
-
-#ifdef CONFIG_I2O_EXT_ADAPTEC
- if (!c->adaptec)
-#endif
- {
- writel((u32) swtype << 16 | (u32) 1 << 8, &msg->body[0]);
- writel(0, &msg->body[1]);
- writel(swid, &msg->body[2]);
- }
-
- status = i2o_msg_post_wait_mem(c, m, 60, &buffer);
-
- if (status != -ETIMEDOUT)
- i2o_dma_free(&c->pdev->dev, &buffer);
-
- if (status != I2O_POST_WAIT_OK)
- return -EIO;
-
- *offset += count;
-
- return count;
-
- free_buffer:
- i2o_dma_free(&c->pdev->dev, &buffer);
-
- nop_msg:
- i2o_msg_nop(c, m);
-
- return rc;
-};
-
-/* attribute for HRT in sysfs */
-static struct bin_attribute i2o_config_hrt_attr = {
- .attr = {
- .name = "hrt",
- .mode = S_IRUGO,
- .owner = THIS_MODULE},
- .size = 0,
- .read = i2o_config_read_hrt
-};
-
-/* attribute for LCT in sysfs */
-static struct bin_attribute i2o_config_lct_attr = {
- .attr = {
- .name = "lct",
- .mode = S_IRUGO,
- .owner = THIS_MODULE},
- .size = 0,
- .read = i2o_config_read_lct
-};
-
-/* IRTOS firmware access */
-I2O_CONFIG_SW_ATTR(irtos, S_IWRSR, I2O_SOFTWARE_MODULE_IRTOS, 0);
-
-#ifdef CONFIG_I2O_EXT_ADAPTEC
-
-/*
- * attribute for BIOS / SMOR, nvram and serial number access on DPT / Adaptec
- * controllers
- */
-I2O_CONFIG_SW_ATTR(bios, S_IWRSR, I2O_SOFTWARE_MODULE_IOP_PRIVATE, 0);
-I2O_CONFIG_SW_ATTR(nvram, S_IWRSR, I2O_SOFTWARE_MODULE_IOP_CONFIG, 0);
-I2O_CONFIG_SW_ATTR(serial, S_IWRSR, I2O_SOFTWARE_MODULE_IOP_CONFIG, 1);
-
-#endif
-
-/**
- * i2o_config_notify_controller_add - Notify of added controller
- * @c: the controller which was added
- *
- * If a I2O controller is added, we catch the notification to add sysfs
- * entries.
- */
-static void i2o_config_notify_controller_add(struct i2o_controller *c)
-{
- struct kobject *kobj = &c->exec->device.kobj;
-
- sysfs_create_bin_file(kobj, &i2o_config_hrt_attr);
- sysfs_create_bin_file(kobj, &i2o_config_lct_attr);
-
- sysfs_create_fops_file(kobj, &i2o_config_attr_irtos);
-#ifdef CONFIG_I2O_EXT_ADAPTEC
- if (c->adaptec) {
- sysfs_create_fops_file(kobj, &i2o_config_attr_bios);
- sysfs_create_fops_file(kobj, &i2o_config_attr_nvram);
- sysfs_create_fops_file(kobj, &i2o_config_attr_serial);
- }
-#endif
-};
-
-/**
- * i2o_config_notify_controller_remove - Notify of removed controller
- * @c: the controller which was removed
- *
- * If a I2O controller is removed, we catch the notification to remove the
- * sysfs entries.
- */
-static void i2o_config_notify_controller_remove(struct i2o_controller *c)
-{
- struct kobject *kobj = &c->exec->device.kobj;
-
-#ifdef CONFIG_I2O_EXT_ADAPTEC
- if (c->adaptec) {
- sysfs_remove_fops_file(kobj, &i2o_config_attr_serial);
- sysfs_remove_fops_file(kobj, &i2o_config_attr_nvram);
- sysfs_remove_fops_file(kobj, &i2o_config_attr_bios);
- }
-#endif
- sysfs_remove_fops_file(kobj, &i2o_config_attr_irtos);
-
- sysfs_remove_bin_file(kobj, &i2o_config_lct_attr);
- sysfs_remove_bin_file(kobj, &i2o_config_hrt_attr);
-};
-
/* Config OSM driver struct */
static struct i2o_driver i2o_config_driver = {
.name = OSM_NAME,
- .notify_controller_add = i2o_config_notify_controller_add,
- .notify_controller_remove = i2o_config_notify_controller_remove
};
#ifdef CONFIG_I2O_CONFIG_OLD_IOCTL
#include <linux/i2o.h>
#include "core.h"
+#define OSM_DESCRIPTION "I2O-subsystem"
+
/* PCI device id table for all I2O controllers */
static struct pci_device_id __devinitdata i2o_pci_ids[] = {
{PCI_DEVICE_CLASS(PCI_CLASS_INTELLIGENT_I2O << 8, 0xffff00)},
if (c->base.virt)
iounmap(c->base.virt);
+
+ pci_release_regions(c->pdev);
}
/**
struct device *dev = &pdev->dev;
int i;
+ if (pci_request_regions(pdev, OSM_DESCRIPTION)) {
+ printk(KERN_ERR "%s: device already claimed\n", c->name);
+ return -ENODEV;
+ }
+
for (i = 0; i < 6; i++) {
/* Skip I/O spaces */
if (!(pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
c->base.virt = ioremap_nocache(c->base.phys, c->base.len);
if (!c->base.virt) {
printk(KERN_ERR "%s: Unable to map controller.\n", c->name);
+ i2o_pci_free(c);
return -ENOMEM;
}
#include "wbsd.h"
#define DRIVER_NAME "wbsd"
-#define DRIVER_VERSION "1.2"
+#define DRIVER_VERSION "1.3"
#ifdef CONFIG_MMC_DEBUG
#define DBG(x...) \
struct e1000_adapter *adapter = netdev_priv(netdev);
disable_irq(adapter->pdev->irq);
e1000_intr(adapter->pdev->irq, netdev, NULL);
+ e1000_clean_tx_irq(adapter);
enable_irq(adapter->pdev->irq);
}
#endif
#define AX25_6PACK_HEADER_LEN 0
-static void sp_start_tx_timer(struct sixpack *);
static void sixpack_decode(struct sixpack *, unsigned char[], int);
static int encode_sixpack(unsigned char *, unsigned char *, int, unsigned char);
/*
- * perform the persistence/slottime algorithm for CSMA access. If the
+ * Perform the persistence/slottime algorithm for CSMA access. If the
* persistence check was successful, write the data to the serial driver.
* Note that in case of DAMA operation, the data is not sent here.
*/
static void sp_xmit_on_air(unsigned long channel)
{
struct sixpack *sp = (struct sixpack *) channel;
- int actual;
+ int actual, when = sp->slottime;
static unsigned char random;
random = random * 17 + 41;
sp->tty->driver->write(sp->tty, &sp->led_state, 1);
sp->status2 = 0;
} else
- sp_start_tx_timer(sp);
+ mod_timer(&sp->tx_t, jiffies + ((when + 1) * HZ) / 100);
}
/* ----> 6pack timer interrupt handler and friends. <---- */
-static void sp_start_tx_timer(struct sixpack *sp)
-{
- int when = sp->slottime;
-
- del_timer(&sp->tx_t);
- sp->tx_t.data = (unsigned long) sp;
- sp->tx_t.function = sp_xmit_on_air;
- sp->tx_t.expires = jiffies + ((when + 1) * HZ) / 100;
- add_timer(&sp->tx_t);
-}
/* Encapsulate one AX.25 frame and stuff into a TTY queue. */
static void sp_encaps(struct sixpack *sp, unsigned char *icp, int len)
sp->xleft = count;
sp->xhead = sp->xbuff;
sp->status2 = count;
- if (sp->duplex == 0)
- sp_start_tx_timer(sp);
+ sp_xmit_on_air((unsigned long)sp);
}
return;
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
#ifndef _PCIEHP_H
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>,<dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>,<kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <dely.l.sy@intel.com>
+ * Send feedback to <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>,<dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>,<kristen.c.accardi@intel.com>
*
*/
#ifndef _SHPCHP_H
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>,<dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>,<kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <dely.l.sy@intel.com>
+ * Send feedback to <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>,<dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>,<kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
- * Send feedback to <greg@kroah.com>, <dely.l.sy@intel.com>
+ * Send feedback to <greg@kroah.com>, <kristen.c.accardi@intel.com>
*
*/
}
}
-static void disable_msi_mode(struct pci_dev *dev, int pos, int type)
+void disable_msi_mode(struct pci_dev *dev, int pos, int type)
{
u16 control;
if (!pci_msi_enable || !dev)
return status;
+ if (dev->no_msi)
+ return status;
+
temp = dev->irq;
if ((status = msi_init()) < 0)
#define pci_msi_quirk 0
#endif
+#ifdef CONFIG_PCI_MSI
+void disable_msi_mode(struct pci_dev *dev, int pos, int type);
+#else
+static inline void disable_msi_mode(struct pci_dev *dev, int pos, int type) { }
+#endif
+
extern int pcie_mch_quirk;
extern struct device_attribute pci_dev_attrs[];
extern struct class_device_attribute class_device_attr_cpuaffinity;
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7320_MCH, quirk_pcie_mch );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7525_MCH, quirk_pcie_mch );
+
+/*
+ * It's possible for the MSI to get corrupted if shpc and acpi
+ * are used together on certain PXH-based systems.
+ */
+static void __devinit quirk_pcie_pxh(struct pci_dev *dev)
+{
+ disable_msi_mode(dev, pci_find_capability(dev, PCI_CAP_ID_MSI),
+ PCI_CAP_ID_MSI);
+ dev->no_msi = 1;
+
+ printk(KERN_WARNING "PCI: PXH quirk detected, "
+ "disabling MSI for SHPC device\n");
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_0, quirk_pcie_pxh);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_1, quirk_pcie_pxh);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_pcie_pxh);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_pcie_pxh);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_pcie_pxh);
+
+
static void __devinit quirk_netmos(struct pci_dev *dev)
{
unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4;
#define __KERNEL_SYSCALLS__
#include <linux/kernel.h>
+#include <linux/kthread.h>
#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/delay.h>
static int kenvctrld(void *__unused)
{
- daemonize("kenvctrld");
- allow_signal(SIGKILL);
- kenvctrld_task = current;
-
printk(KERN_INFO "bbc_envctrl: kenvctrld starting...\n");
last_warning_jiffies = jiffies - WARN_INTERVAL;
for (;;) {
struct bbc_fan_control *fp;
msleep_interruptible(POLL_INTERVAL);
- if (signal_pending(current))
+ if (kthread_should_stop())
break;
for (tp = all_bbc_temps; tp; tp = tp->next) {
int temp_index = 0;
int fan_index = 0;
int devidx = 0;
- int err = 0;
while ((echild = bbc_i2c_getdev(devidx++)) != NULL) {
if (!strcmp(echild->prom_name, "temperature"))
if (!strcmp(echild->prom_name, "fan-control"))
attach_one_fan(echild, fan_index++);
}
- if (temp_index != 0 && fan_index != 0)
- err = kernel_thread(kenvctrld, NULL, CLONE_FS | CLONE_FILES);
- return err;
+ if (temp_index != 0 && fan_index != 0) {
+ kenvctrld_task = kthread_run(kenvctrld, NULL, "kenvctrld");
+ if (IS_ERR(kenvctrld_task))
+ return PTR_ERR(kenvctrld_task);
+ }
+
+ return 0;
}
static void destroy_one_temp(struct bbc_cpu_temperature *tp)
struct bbc_cpu_temperature *tp;
struct bbc_fan_control *fp;
- if (kenvctrld_task != NULL) {
- force_sig(SIGKILL, kenvctrld_task);
- for (;;) {
- struct task_struct *p;
- int found = 0;
-
- read_lock(&tasklist_lock);
- for_each_process(p) {
- if (p == kenvctrld_task) {
- found = 1;
- break;
- }
- }
- read_unlock(&tasklist_lock);
- if (!found)
- break;
- msleep(1000);
- }
- kenvctrld_task = NULL;
- }
+ kthread_stop(kenvctrld_task);
tp = all_bbc_temps;
while (tp != NULL) {
#include <linux/config.h>
#include <linux/module.h>
#include <linux/sched.h>
+#include <linux/kthread.h>
#include <linux/errno.h>
#include <linux/delay.h>
#include <linux/ioport.h>
poll_interval = 5000; /* TODO env_mon_interval */
- daemonize("kenvctrld");
- allow_signal(SIGKILL);
-
- kenvctrld_task = current;
-
printk(KERN_INFO "envctrl: %s starting...\n", current->comm);
for (;;) {
- if(msleep_interruptible(poll_interval))
- break;
+ msleep_interruptible(poll_interval);
+ if (kthread_should_stop())
+ break;
+
for (whichcpu = 0; whichcpu < ENVCTRL_MAX_CPU; ++whichcpu) {
if (0 < envctrl_read_cpu_info(whichcpu, cputemp,
ENVCTRL_CPUTEMP_MON,
static int __init envctrl_init(void)
{
-#ifdef CONFIG_PCI
struct linux_ebus *ebus = NULL;
struct linux_ebus_device *edev = NULL;
struct linux_ebus_child *edev_child = NULL;
i2c_childlist[i].addr, (0 == i) ? ("\n") : (" "));
}
- err = kernel_thread(kenvctrld, NULL, CLONE_FS | CLONE_FILES);
- if (err < 0)
+ kenvctrld_task = kthread_run(kenvctrld, NULL, "kenvctrld");
+ if (IS_ERR(kenvctrld_task)) {
+ err = PTR_ERR(kenvctrld_task);
goto out_deregister;
+ }
return 0;
kfree(i2c_childlist[i].tables);
}
return err;
-#else
- return -ENODEV;
-#endif
}
static void __exit envctrl_cleanup(void)
{
int i;
- if (NULL != kenvctrld_task) {
- force_sig(SIGKILL, kenvctrld_task);
- for (;;) {
- struct task_struct *p;
- int found = 0;
-
- read_lock(&tasklist_lock);
- for_each_process(p) {
- if (p == kenvctrld_task) {
- found = 1;
- break;
- }
- }
- read_unlock(&tasklist_lock);
-
- if (!found)
- break;
-
- msleep(1000);
- }
- kenvctrld_task = NULL;
- }
+ kthread_stop(kenvctrld_task);
iounmap(i2c);
misc_deregister(&envctrl_dev);
* cross a page boundy.
*/
#define SEGMENTX_LEN (sizeof(struct SGentry)*DC395x_MAX_SG_LISTENTRY)
-#define VIRTX_LEN (sizeof(void *) * DC395x_MAX_SG_LISTENTRY)
+
struct SGentry {
u32 address; /* bus! address */
u8 sg_count; /* No of HW sg entries for this request */
u8 sg_index; /* Index of HW sg entry for this request */
u32 total_xfer_length; /* Total number of bytes remaining to be transfered */
- void **virt_map;
unsigned char *virt_addr; /* Virtual address of current transfer position */
/*
reqlen, cmd->request_buffer, cmd->use_sg,
srb->sg_count);
+ srb->virt_addr = page_address(sl->page);
for (i = 0; i < srb->sg_count; i++) {
- u32 seglen = (u32)sg_dma_len(sl + i);
- sgp[i].address = (u32)sg_dma_address(sl + i);
+ u32 busaddr = (u32)sg_dma_address(&sl[i]);
+ u32 seglen = (u32)sl[i].length;
+ sgp[i].address = busaddr;
sgp[i].length = seglen;
srb->total_xfer_length += seglen;
- srb->virt_map[i] = kmap(sl[i].page);
}
- srb->virt_addr = srb->virt_map[0];
sgp += srb->sg_count - 1;
/*
int segment = cmd->use_sg;
u32 xferred = srb->total_xfer_length - left; /* bytes transfered */
struct SGentry *psge = srb->segment_x + srb->sg_index;
- void **virt = srb->virt_map;
dprintkdbg(DBG_0,
"sg_update_list: Transfered %i of %i bytes, %i remain\n",
/* We have to walk the scatterlist to find it */
sg = (struct scatterlist *)cmd->request_buffer;
- idx = 0;
while (segment--) {
unsigned long mask =
~((unsigned long)sg->length - 1) & PAGE_MASK;
if ((sg_dma_address(sg) & mask) == (psge->address & mask)) {
- srb->virt_addr = virt[idx] + (psge->address & ~PAGE_MASK);
+ srb->virt_addr = (page_address(sg->page)
+ + psge->address -
+ (psge->address & PAGE_MASK));
return;
}
++sg;
- ++idx;
}
dprintkl(KERN_ERR, "sg_update_list: sg_to_virt failed\n");
DC395x_read32(acb, TRM_S1040_DMA_CXCNT));
}
/*
- * calculate all the residue data that not yet transfered
+ * calculate all the residue data that not yet tranfered
* SCSI transfer counter + left in SCSI FIFO data
*
* .....TRM_S1040_SCSI_COUNTER (24bits)
struct scsi_cmnd *cmd = srb->cmd;
enum dma_data_direction dir = cmd->sc_data_direction;
if (cmd->use_sg && dir != PCI_DMA_NONE) {
- int i;
/* unmap DC395x SG list */
dprintkdbg(DBG_SG, "pci_unmap_srb: list=%08x(%05x)\n",
srb->sg_bus_addr, SEGMENTX_LEN);
dprintkdbg(DBG_SG, "pci_unmap_srb: segs=%i buffer=%p\n",
cmd->use_sg, cmd->request_buffer);
/* unmap the sg segments */
- for (i = 0; i < srb->sg_count; i++)
- kunmap(virt_to_page(srb->virt_map[i]));
pci_unmap_sg(acb->dev,
(struct scatterlist *)cmd->request_buffer,
cmd->use_sg, dir);
if (cmd->use_sg) {
struct scatterlist* sg = (struct scatterlist *)cmd->request_buffer;
- ptr = (struct ScsiInqData *)(srb->virt_map[0] + sg->offset);
+ ptr = (struct ScsiInqData *)(page_address(sg->page) + sg->offset);
} else {
ptr = (struct ScsiInqData *)(cmd->request_buffer);
}
const unsigned srbs_per_page = PAGE_SIZE/SEGMENTX_LEN;
for (i = 0; i < DC395x_MAX_SRB_CNT; i += srbs_per_page)
- kfree(acb->srb_array[i].segment_x);
-
- vfree(acb->srb_array[0].virt_map);
+ if (acb->srb_array[i].segment_x)
+ kfree(acb->srb_array[i].segment_x);
}
int srb_idx = 0;
unsigned i = 0;
struct SGentry *ptr;
- void **virt_array;
- for (i = 0; i < DC395x_MAX_SRB_CNT; i++) {
+ for (i = 0; i < DC395x_MAX_SRB_CNT; i++)
acb->srb_array[i].segment_x = NULL;
- acb->srb_array[i].virt_map = NULL;
- }
dprintkdbg(DBG_1, "Allocate %i pages for SG tables\n", pages);
while (pages--) {
ptr + (i * DC395x_MAX_SG_LISTENTRY);
else
dprintkl(KERN_DEBUG, "No space for tmsrb SG table reserved?!\n");
-
- virt_array = vmalloc((DC395x_MAX_SRB_CNT + 1) * DC395x_MAX_SG_LISTENTRY * sizeof(void*));
-
- if (!virt_array) {
- adapter_sg_tables_free(acb);
- return 1;
- }
-
- for (i = 0; i < DC395x_MAX_SRB_CNT + 1; i++) {
- acb->srb_array[i].virt_map = virt_array;
- virt_array += DC395x_MAX_SG_LISTENTRY;
- }
-
return 0;
}
raptorFlag = TRUE;
}
-
+ if (pci_request_regions(pDev, "dpt_i2o")) {
+ PERROR("dpti: adpt_config_hba: pci request region failed\n");
+ return -EINVAL;
+ }
base_addr_virt = ioremap(base_addr0_phys,hba_map0_area_size);
if (!base_addr_virt) {
+ pci_release_regions(pDev);
PERROR("dpti: adpt_config_hba: io remap failed\n");
return -EINVAL;
}
if (!msg_addr_virt) {
PERROR("dpti: adpt_config_hba: io remap failed on BAR1\n");
iounmap(base_addr_virt);
+ pci_release_regions(pDev);
return -EINVAL;
}
} else {
iounmap(msg_addr_virt);
}
iounmap(base_addr_virt);
+ pci_release_regions(pDev);
return -ENOMEM;
}
memset(pHba, 0, sizeof(adpt_hba));
up(&adpt_configuration_lock);
iounmap(pHba->base_addr_virt);
+ pci_release_regions(pHba->pDev);
if(pHba->msg_addr_virt != pHba->base_addr_virt){
iounmap(pHba->msg_addr_virt);
}
* appropriate place
*/
host->host_failed--;
+ INIT_LIST_HEAD(&host->eh_cmd_q);
DPRINTK("EXIT\n");
return 0;
for (i = 0; i < last; i++) {
buf[idx++] = cpu_to_le32(sg_dma_address(&sg[i]));
buf[idx++] = cpu_to_le32(sg_dma_len(&sg[i]));
- total_len += sg[i].length;
+ total_len += sg_dma_len(&sg[i]);
}
buf[idx - 1] |= cpu_to_le32(ATA_PRD_EOT);
sgt_len = idx * 4;
unsigned long flags;
const int size = sizeof(struct scsi_target)
+ shost->transportt->target_size;
- struct scsi_target *starget = kmalloc(size, GFP_ATOMIC);
+ struct scsi_target *starget;
struct scsi_target *found_target;
+ /*
+ * Obtain the real parent from the transport. The transport
+ * is allowed to fail (no error) if there is nothing at that
+ * target id.
+ */
+ if (shost->transportt->target_parent) {
+ spin_lock_irqsave(shost->host_lock, flags);
+ parent = shost->transportt->target_parent(shost, channel, id);
+ spin_unlock_irqrestore(shost->host_lock, flags);
+ if (!parent)
+ return NULL;
+ }
+
+ starget = kmalloc(size, GFP_KERNEL);
if (!starget) {
printk(KERN_ERR "%s: allocation failure\n", __FUNCTION__);
return NULL;
return &i->rport_attr_cont.ac == cont;
}
+
+/*
+ * Must be called with shost->host_lock held
+ */
+static struct device *fc_target_parent(struct Scsi_Host *shost,
+ int channel, uint id)
+{
+ struct fc_rport *rport;
+
+ list_for_each_entry(rport, &fc_host_rports(shost), peers)
+ if ((rport->channel == channel) &&
+ (rport->scsi_target_id == id))
+ return &rport->dev;
+
+ return NULL;
+}
+
struct scsi_transport_template *
fc_attach_transport(struct fc_function_template *ft)
{
/* Transport uses the shost workq for scsi scanning */
i->t.create_work_queue = 1;
+
+ i->t.target_parent = fc_target_parent;
/*
* Setup SCSI Target Attributes.
#define TX_NUM_FIFO 4
#define TX_BUF_SIZE 32
+#define SCC_WAIT_CLOSING 100
+
struct uart_cpm_port {
struct uart_port port;
- u16 rx_nrfifos;
+ u16 rx_nrfifos;
u16 rx_fifosize;
- u16 tx_nrfifos;
+ u16 tx_nrfifos;
u16 tx_fifosize;
- smc_t *smcp;
+ smc_t *smcp;
smc_uart_t *smcup;
scc_t *sccp;
scc_uart_t *sccup;
int bits;
/* Keep track of 'odd' SMC2 wirings */
int is_portb;
+ /* wait on close if needed */
+ int wait_closing;
};
extern int cpm_uart_port_map[UART_NR];
*
* Maintainer: Kumar Gala (kumar.gala@freescale.com) (CPM2)
* Pantelis Antoniou (panto@intracom.gr) (CPM1)
- *
+ *
* Copyright (C) 2004 Freescale Semiconductor, Inc.
* (C) 2004 Intracom, S.A.
+ * (C) 2005 MontaVista Software, Inc. by Vitaly Bordug <vbordug@ru.mvista.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
/**************************************************************/
+static inline unsigned long cpu2cpm_addr(void *addr)
+{
+ if ((unsigned long)addr >= CPM_ADDR)
+ return (unsigned long)addr;
+ return virt_to_bus(addr);
+}
+
+static inline void *cpm2cpu_addr(unsigned long addr)
+{
+ if (addr >= CPM_ADDR)
+ return (void *)addr;
+ return bus_to_virt(addr);
+}
+
/*
- * Check, if transmit buffers are processed
+ * Check, if transmit buffers are processed
*/
static unsigned int cpm_uart_tx_empty(struct uart_port *port)
{
}
if (cpm_uart_tx_pump(port) != 0) {
- if (IS_SMC(pinfo))
+ if (IS_SMC(pinfo)) {
smcp->smc_smcm |= SMCM_TX;
- else
+ smcp->smc_smcmr |= SMCMR_TEN;
+ } else {
sccp->scc_sccm |= UART_SCCM_TX;
+ pinfo->sccp->scc_gsmrl |= SCC_GSMRL_ENT;
+ }
}
}
/*
- * Stop receiver
+ * Stop receiver
*/
static void cpm_uart_stop_rx(struct uart_port *port)
{
}
/*
- * Generate a break.
+ * Generate a break.
*/
static void cpm_uart_break_ctl(struct uart_port *port, int break_state)
{
/* get number of characters, and check spce in flip-buffer */
i = bdp->cbd_datlen;
- /* If we have not enough room in tty flip buffer, then we try
+ /* If we have not enough room in tty flip buffer, then we try
* later, which will be the next rx-interrupt or a timeout
*/
if ((tty->flip.count + i) >= TTY_FLIPBUF_SIZE) {
}
/* get pointer */
- cp = (unsigned char *)bus_to_virt(bdp->cbd_bufaddr);
+ cp = cpm2cpu_addr(bdp->cbd_bufaddr);
/* loop through the buffer */
while (i-- > 0) {
} /* End while (i--) */
/* This BD is ready to be used again. Clear status. get next */
- bdp->cbd_sc &= ~(BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV);
+ bdp->cbd_sc &= ~(BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV | BD_SC_ID);
bdp->cbd_sc |= BD_SC_EMPTY;
if (bdp->cbd_sc & BD_SC_WRAP)
bdp = pinfo->rx_bd_base;
else
bdp++;
+
} /* End for (;;) */
/* Write back buffer pointer */
if (IS_SMC(pinfo)) {
events = smcp->smc_smce;
+ smcp->smc_smce = events;
if (events & SMCM_BRKE)
uart_handle_break(port);
if (events & SMCM_RX)
cpm_uart_int_rx(port, regs);
if (events & SMCM_TX)
cpm_uart_int_tx(port, regs);
- smcp->smc_smce = events;
} else {
events = sccp->scc_scce;
+ sccp->scc_scce = events;
if (events & UART_SCCM_BRKE)
uart_handle_break(port);
if (events & UART_SCCM_RX)
cpm_uart_int_rx(port, regs);
if (events & UART_SCCM_TX)
cpm_uart_int_tx(port, regs);
- sccp->scc_scce = events;
}
return (events) ? IRQ_HANDLED : IRQ_NONE;
}
{
int retval;
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
+ int line = pinfo - cpm_uart_ports;
pr_debug("CPM uart[%d]:startup\n", port->line);
pinfo->sccp->scc_sccm |= UART_SCCM_RX;
}
+ if (!(pinfo->flags & FLAG_CONSOLE))
+ cpm_line_cr_cmd(line,CPM_CR_INIT_TRX);
return 0;
}
+inline void cpm_uart_wait_until_send(struct uart_cpm_port *pinfo)
+{
+ unsigned long target_jiffies = jiffies + pinfo->wait_closing;
+
+ while (!time_after(jiffies, target_jiffies))
+ schedule();
+}
+
/*
* Shutdown the uart
*/
/* If the port is not the console, disable Rx and Tx. */
if (!(pinfo->flags & FLAG_CONSOLE)) {
+ /* Wait for all the BDs marked sent */
+ while(!cpm_uart_tx_empty(port))
+ schedule_timeout(2);
+ if(pinfo->wait_closing)
+ cpm_uart_wait_until_send(pinfo);
+
/* Stop uarts */
if (IS_SMC(pinfo)) {
volatile smc_t *smcp = pinfo->smcp;
*/
if ((termios->c_cflag & CREAD) == 0)
port->read_status_mask &= ~BD_SC_EMPTY;
-
+
spin_lock_irqsave(&port->lock, flags);
/* Start bit has not been added (so don't, because we would just
/* Pick next descriptor and fill from buffer */
bdp = pinfo->tx_cur;
- p = bus_to_virt(bdp->cbd_bufaddr);
+ p = cpm2cpu_addr(bdp->cbd_bufaddr);
+
*p++ = xmit->buf[xmit->tail];
bdp->cbd_datlen = 1;
bdp->cbd_sc |= BD_SC_READY;
while (!(bdp->cbd_sc & BD_SC_READY) && (xmit->tail != xmit->head)) {
count = 0;
- p = bus_to_virt(bdp->cbd_bufaddr);
+ p = cpm2cpu_addr(bdp->cbd_bufaddr);
while (count < pinfo->tx_fifosize) {
*p++ = xmit->buf[xmit->tail];
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
}
bdp->cbd_datlen = count;
bdp->cbd_sc |= BD_SC_READY;
+ __asm__("eieio");
/* Get next BD. */
if (bdp->cbd_sc & BD_SC_WRAP)
bdp = pinfo->tx_bd_base;
mem_addr = pinfo->mem_addr;
bdp = pinfo->rx_cur = pinfo->rx_bd_base;
for (i = 0; i < (pinfo->rx_nrfifos - 1); i++, bdp++) {
- bdp->cbd_bufaddr = virt_to_bus(mem_addr);
+ bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr);
bdp->cbd_sc = BD_SC_EMPTY | BD_SC_INTRPT;
mem_addr += pinfo->rx_fifosize;
}
-
- bdp->cbd_bufaddr = virt_to_bus(mem_addr);
+
+ bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr);
bdp->cbd_sc = BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT;
/* Set the physical address of the host memory
mem_addr = pinfo->mem_addr + L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize);
bdp = pinfo->tx_cur = pinfo->tx_bd_base;
for (i = 0; i < (pinfo->tx_nrfifos - 1); i++, bdp++) {
- bdp->cbd_bufaddr = virt_to_bus(mem_addr);
+ bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr);
bdp->cbd_sc = BD_SC_INTRPT;
mem_addr += pinfo->tx_fifosize;
}
-
- bdp->cbd_bufaddr = virt_to_bus(mem_addr);
+
+ bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr);
bdp->cbd_sc = BD_SC_WRAP | BD_SC_INTRPT;
}
/* Using idle charater time requires some additional tuning. */
up->smc_mrblr = pinfo->rx_fifosize;
up->smc_maxidl = pinfo->rx_fifosize;
+ up->smc_brklen = 0;
+ up->smc_brkec = 0;
up->smc_brkcr = 1;
cpm_line_cr_cmd(line, CPM_CR_INIT_TRX);
/*
* Setup any port IO, connect any baud rate generators,
* etc. This is expected to be handled by board
- * dependant code
+ * dependant code
*/
if (pinfo->set_lineif)
pinfo->set_lineif(pinfo);
return ret;
cpm_uart_initbd(pinfo);
+ if (IS_SMC(pinfo))
+ cpm_uart_init_smc(pinfo);
+ else
+ cpm_uart_init_scc(pinfo);
return 0;
}
.flags = FLAG_SMC,
.tx_nrfifos = TX_NUM_FIFO,
.tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
+ .rx_nrfifos = RX_NUM_FIFO,
.rx_fifosize = RX_BUF_SIZE,
.set_lineif = smc1_lineif,
},
.flags = FLAG_SMC,
.tx_nrfifos = TX_NUM_FIFO,
.tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
+ .rx_nrfifos = RX_NUM_FIFO,
.rx_fifosize = RX_BUF_SIZE,
.set_lineif = smc2_lineif,
#ifdef CONFIG_SERIAL_CPM_ALT_SMC2
},
.tx_nrfifos = TX_NUM_FIFO,
.tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
+ .rx_nrfifos = RX_NUM_FIFO,
.rx_fifosize = RX_BUF_SIZE,
.set_lineif = scc1_lineif,
+ .wait_closing = SCC_WAIT_CLOSING,
},
[UART_SCC2] = {
.port = {
},
.tx_nrfifos = TX_NUM_FIFO,
.tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
+ .rx_nrfifos = RX_NUM_FIFO,
.rx_fifosize = RX_BUF_SIZE,
.set_lineif = scc2_lineif,
+ .wait_closing = SCC_WAIT_CLOSING,
},
[UART_SCC3] = {
.port = {
},
.tx_nrfifos = TX_NUM_FIFO,
.tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
+ .rx_nrfifos = RX_NUM_FIFO,
.rx_fifosize = RX_BUF_SIZE,
.set_lineif = scc3_lineif,
+ .wait_closing = SCC_WAIT_CLOSING,
},
[UART_SCC4] = {
.port = {
},
.tx_nrfifos = TX_NUM_FIFO,
.tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
+ .rx_nrfifos = RX_NUM_FIFO,
.rx_fifosize = RX_BUF_SIZE,
.set_lineif = scc4_lineif,
+ .wait_closing = SCC_WAIT_CLOSING,
},
};
* If the buffer address is in the CPM DPRAM, don't
* convert it.
*/
- if ((uint) (bdp->cbd_bufaddr) > (uint) CPM_ADDR)
- cp = (unsigned char *) (bdp->cbd_bufaddr);
- else
- cp = bus_to_virt(bdp->cbd_bufaddr);
-
+ cp = cpm2cpu_addr(bdp->cbd_bufaddr);
+
*cp = *s;
bdp->cbd_datlen = 1;
while ((bdp->cbd_sc & BD_SC_READY) != 0)
;
- if ((uint) (bdp->cbd_bufaddr) > (uint) CPM_ADDR)
- cp = (unsigned char *) (bdp->cbd_bufaddr);
- else
- cp = bus_to_virt(bdp->cbd_bufaddr);
+ cp = cpm2cpu_addr(bdp->cbd_bufaddr);
*cp = 13;
bdp->cbd_datlen = 1;
port =
(struct uart_port *)&cpm_uart_ports[cpm_uart_port_map[co->index]];
pinfo = (struct uart_cpm_port *)port;
-
+
pinfo->flags |= FLAG_CONSOLE;
if (options) {
/*
* Setup any port IO, connect any baud rate generators,
* etc. This is expected to be handled by board
- * dependant code
+ * dependant code
*/
if (pinfo->set_lineif)
pinfo->set_lineif(pinfo);
return 0;
}
-extern struct uart_driver cpm_reg;
+static struct uart_driver cpm_reg;
static struct console cpm_scc_uart_console = {
- .name "ttyCPM",
- .write cpm_uart_console_write,
- .device uart_console_device,
- .setup cpm_uart_console_setup,
- .flags CON_PRINTBUFFER,
- .index -1,
+ .name = "ttyCPM",
+ .write = cpm_uart_console_write,
+ .device = uart_console_device,
+ .setup = cpm_uart_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
.data = &cpm_reg,
};
*
* Maintainer: Kumar Gala (kumar.gala@freescale.com) (CPM2)
* Pantelis Antoniou (panto@intracom.gr) (CPM1)
- *
+ *
* Copyright (C) 2004 Freescale Semiconductor, Inc.
* (C) 2004 Intracom, S.A.
*
void smc1_lineif(struct uart_cpm_port *pinfo)
{
volatile cpm8xx_t *cp = cpmp;
+
+ (void)cp; /* fix warning */
+#if defined (CONFIG_MPC885ADS)
+ /* Enable SMC1 transceivers */
+ {
+ cp->cp_pepar |= 0x000000c0;
+ cp->cp_pedir &= ~0x000000c0;
+ cp->cp_peso &= ~0x00000040;
+ cp->cp_peso |= 0x00000080;
+ }
+#elif defined (CONFIG_MPC86XADS)
unsigned int iobits = 0x000000c0;
if (!pinfo->is_portb) {
((immap_t *)IMAP_ADDR)->im_ioport.iop_padir &= ~iobits;
((immap_t *)IMAP_ADDR)->im_ioport.iop_paodr &= ~iobits;
}
-
-#ifdef CONFIG_MPC885ADS
- /* Enable SMC1 transceivers */
- {
- volatile uint __iomem *bcsr1 = ioremap(BCSR1, 4);
- uint tmp;
-
- tmp = in_be32(bcsr1);
- tmp &= ~BCSR1_RS232EN_1;
- out_be32(bcsr1, tmp);
- iounmap(bcsr1);
- }
#endif
-
pinfo->brg = 1;
}
void smc2_lineif(struct uart_cpm_port *pinfo)
{
-#ifdef CONFIG_MPC885ADS
volatile cpm8xx_t *cp = cpmp;
- volatile uint __iomem *bcsr1;
- uint tmp;
+ (void)cp; /* fix warning */
+#if defined (CONFIG_MPC885ADS)
cp->cp_pepar |= 0x00000c00;
cp->cp_pedir &= ~0x00000c00;
cp->cp_peso &= ~0x00000400;
cp->cp_peso |= 0x00000800;
+#elif defined (CONFIG_MPC86XADS)
+ unsigned int iobits = 0x00000c00;
+
+ if (!pinfo->is_portb) {
+ cp->cp_pbpar |= iobits;
+ cp->cp_pbdir &= ~iobits;
+ cp->cp_pbodr &= ~iobits;
+ } else {
+ ((immap_t *)IMAP_ADDR)->im_ioport.iop_papar |= iobits;
+ ((immap_t *)IMAP_ADDR)->im_ioport.iop_padir &= ~iobits;
+ ((immap_t *)IMAP_ADDR)->im_ioport.iop_paodr &= ~iobits;
+ }
- /* Enable SMC2 transceivers */
- bcsr1 = ioremap(BCSR1, 4);
- tmp = in_be32(bcsr1);
- tmp &= ~BCSR1_RS232EN_2;
- out_be32(bcsr1, tmp);
- iounmap(bcsr1);
#endif
pinfo->brg = 2;
}
/*
- * Allocate DP-Ram and memory buffers. We need to allocate a transmit and
+ * Allocate DP-Ram and memory buffers. We need to allocate a transmit and
* receive buffer descriptors from dual port ram, and a character
* buffer area from host mem. If we are allocating for the console we need
* to do it from bootmem
memsz = L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize) +
L1_CACHE_ALIGN(pinfo->tx_nrfifos * pinfo->tx_fifosize);
if (is_con) {
+ /* was hostalloc but changed cause it blows away the */
+ /* large tlb mapping when pinning the kernel area */
mem_addr = (u8 *) cpm_dpram_addr(cpm_dpalloc(memsz, 8));
dma_addr = 0;
} else
goto exit;
}
- x = le16_to_cpu(*(__le16 *) &data[2]);
- y = le16_to_cpu(*(__le16 *) &data[4]);
-
input_regs(dev, regs);
if (data[1] & 0x10) { /* in prox */
}
}
- if (data[1] & 0x80) {
+ if (data[1] & 0x90) {
+ x = le16_to_cpu(*(__le16 *) &data[2]);
+ y = le16_to_cpu(*(__le16 *) &data[4]);
input_report_abs(dev, ABS_X, x);
input_report_abs(dev, ABS_Y, y);
- }
- if (wacom->tool[0] != BTN_TOOL_MOUSE) {
- input_report_abs(dev, ABS_PRESSURE, le16_to_cpu(*(__le16 *) &data[6]));
- input_report_key(dev, BTN_TOUCH, data[1] & 0x01);
- input_report_key(dev, BTN_STYLUS, data[1] & 0x02);
- input_report_key(dev, BTN_STYLUS2, data[1] & 0x04);
+ if (wacom->tool[0] != BTN_TOOL_MOUSE) {
+ input_report_abs(dev, ABS_PRESSURE, le16_to_cpu(*(__le16 *) &data[6]));
+ input_report_key(dev, BTN_TOUCH, data[1] & 0x01);
+ input_report_key(dev, BTN_STYLUS, data[1] & 0x02);
+ input_report_key(dev, BTN_STYLUS2, data[1] & 0x04);
+ }
}
input_report_key(dev, wacom->tool[0], data[1] & 0x10);
/* Cintiq doesn't send data when RDY bit isn't set */
if ((wacom->features->type == CINTIQ) && !(data[1] & 0x40))
- return;
+ goto exit;
if (wacom->features->type >= INTUOS3) {
input_report_abs(dev, ABS_X, (data[2] << 9) | (data[3] << 1) | ((data[9] >> 1) & 1));
* The USB Monitor, inspired by Dave Harding's USBMon.
*
* mon_main.c: Main file, module initiation and exit, registrations, etc.
+ *
+ * Copyright (C) 2005 Pete Zaitcev (zaitcev@redhat.com)
*/
#include <linux/kernel.h>
mondir = debugfs_create_dir("usbmon", NULL);
if (IS_ERR(mondir)) {
- printk(KERN_NOTICE TAG ": debugs is not available\n");
+ printk(KERN_NOTICE TAG ": debugfs is not available\n");
return -ENODEV;
}
if (mondir == NULL) {
/*
* The USB Monitor, inspired by Dave Harding's USBMon.
+ *
+ * Copyright (C) 2005 Pete Zaitcev (zaitcev@redhat.com)
*/
#ifndef __USB_MON_H
int
fb_set_var(struct fb_info *info, struct fb_var_screeninfo *var)
{
- int err;
+ int err, flags = info->flags;
if (var->activate & FB_ACTIVATE_INV_MODE) {
struct fb_videomode mode1, mode2;
!list_empty(&info->modelist))
err = fb_add_videomode(&mode, &info->modelist);
- if (!err && info->flags & FBINFO_MISC_USEREVENT) {
+ if (!err && (flags & FBINFO_MISC_USEREVENT)) {
struct fb_event event;
info->flags &= ~FBINFO_MISC_USEREVENT;
return -ENODEV;
}
- /* Map the fb and MMIO regions */
- dinfo->aperture.virtual = (u8 __iomem *)ioremap_nocache
- (dinfo->aperture.physical, dinfo->aperture.size);
- if (!dinfo->aperture.virtual) {
- ERR_MSG("Cannot remap FB region.\n");
- cleanup(dinfo);
- return -ENODEV;
- }
- dinfo->mmio_base =
- (u8 __iomem *)ioremap_nocache(dinfo->mmio_base_phys,
- INTEL_REG_SIZE);
- if (!dinfo->mmio_base) {
- ERR_MSG("Cannot remap MMIO region.\n");
- cleanup(dinfo);
- return -ENODEV;
- }
-
/* Get the chipset info. */
dinfo->pci_chipset = pdev->device;
dinfo->accel = 0;
}
+ if (MB(voffset) < stolen_size)
+ offset = (stolen_size >> 12);
+ else
+ offset = ROUND_UP_TO_PAGE(MB(voffset))/GTT_PAGE_SIZE;
+
/* Framebuffer parameters - Use all the stolen memory if >= vram */
- if (ROUND_UP_TO_PAGE(stolen_size) >= MB(vram)) {
+ if (ROUND_UP_TO_PAGE(stolen_size) >= ((offset << 12) + MB(vram))) {
dinfo->fb.size = ROUND_UP_TO_PAGE(stolen_size);
+ dinfo->fb.offset = 0;
dinfo->fbmem_gart = 0;
} else {
dinfo->fb.size = MB(vram);
return -ENODEV;
}
- if (MB(voffset) < stolen_size)
- offset = (stolen_size >> 12);
- else
- offset = ROUND_UP_TO_PAGE(MB(voffset))/GTT_PAGE_SIZE;
-
/* set the mem offsets - set them after the already used pages */
if (dinfo->accel) {
dinfo->ring.offset = offset + gtt_info.current_memory;
+ (dinfo->cursor.size >> 12);
}
+ /* Map the fb and MMIO regions */
+ /* ioremap only up to the end of used aperture */
+ dinfo->aperture.virtual = (u8 __iomem *)ioremap_nocache
+ (dinfo->aperture.physical, (dinfo->fb.offset << 12)
+ + dinfo->fb.size);
+ if (!dinfo->aperture.virtual) {
+ ERR_MSG("Cannot remap FB region.\n");
+ cleanup(dinfo);
+ return -ENODEV;
+ }
+
+ dinfo->mmio_base =
+ (u8 __iomem *)ioremap_nocache(dinfo->mmio_base_phys,
+ INTEL_REG_SIZE);
+ if (!dinfo->mmio_base) {
+ ERR_MSG("Cannot remap MMIO region.\n");
+ cleanup(dinfo);
+ return -ENODEV;
+ }
+
/* Allocate memories (which aren't stolen) */
if (dinfo->accel) {
if (!(dinfo->gtt_ring_mem =
DPRINTK("reg_lccr2 0x%08x\n", (unsigned int) fbi->reg_lccr2);
DPRINTK("reg_lccr3 0x%08x\n", (unsigned int) fbi->reg_lccr3);
+ /* enable LCD controller clock */
+ pxa_set_cken(CKEN16_LCD, 1);
+
/* Sequence from 11.7.10 */
LCCR3 = fbi->reg_lccr3;
LCCR2 = fbi->reg_lccr2;
schedule_timeout(20 * HZ / 1000);
remove_wait_queue(&fbi->ctrlr_wait, &wait);
+
+ /* disable LCD controller clock */
+ pxa_set_cken(CKEN16_LCD, 0);
}
/*
ret = -ENOMEM;
goto failed;
}
- /* enable LCD controller clock */
- pxa_set_cken(CKEN16_LCD, 1);
ret = request_irq(IRQ_LCD, pxafb_handle_irq, SA_INTERRUPT, "LCD", fbi);
if (ret) {
* Return 0 - device(s) present, 1 - no devices present.
*/
if (w1_reset_bus(dev)) {
- dev_info(&dev->dev, "No devices present on the wire.\n");
+ dev_dbg(&dev->dev, "No devices present on the wire.\n");
break;
}
+Version 1.35
+------------
+Add writepage performance improvements. Fix path name conversions
+for long filenames on mounts which were done with "mapchars" mount option
+specified.
+
Version 1.34
------------
Fix error mapping of the TOO_MANY_LINKS (hardlinks) case.
if(name_len < PATH_MAX) {
memcpy(pSMB->ResumeFileName, psrch_inf->presume_name, name_len);
byte_count += name_len;
+ /* 14 byte parm len above enough for 2 byte null terminator */
+ pSMB->ResumeFileName[name_len] = 0;
+ pSMB->ResumeFileName[name_len+1] = 0;
} else {
rc = -EINVAL;
goto FNext2_err_exit;
src_char = source[i];
switch (src_char) {
case 0:
+ target[j] = 0;
goto ctoUCS_out;
case ':':
target[j] = cpu_to_le16(UNI_COLON);
return ERR_PTR(ret);
}
- dev->last_wd = ret;
+ dev->last_wd = watch->wd;
watch->mask = mask;
atomic_set(&watch->count, 0);
INIT_LIST_HEAD(&watch->d_list);
{
jfs_info("In jfs_delete_inode, inode = 0x%p", inode);
+ if (is_bad_inode(inode) ||
+ (JFS_IP(inode)->fileset != cpu_to_le32(FILESYSTEM_I)))
+ return;
+
if (test_cflag(COMMIT_Freewmap, inode))
jfs_free_zero_link(inode);
static bio_end_io_t lbmIODone;
static void lbmStartIO(struct lbuf * bp);
static void lmGCwrite(struct jfs_log * log, int cant_block);
-static int lmLogSync(struct jfs_log * log, int nosyncwait);
+static int lmLogSync(struct jfs_log * log, int hard_sync);
* if new sync address is available
* (normally the case if sync() is executed by back-ground
* process).
- * if not, explicitly run jfs_blogsync() to initiate
- * getting of new sync address.
* calculate new value of i_nextsync which determines when
* this code is called again.
*
* PARAMETERS: log - log structure
- * nosyncwait - 1 if called asynchronously
+ * hard_sync - 1 to force all metadata to be written
*
* RETURN: 0
*
* serialization: LOG_LOCK() held on entry/exit
*/
-static int lmLogSync(struct jfs_log * log, int nosyncwait)
+static int lmLogSync(struct jfs_log * log, int hard_sync)
{
int logsize;
int written; /* written since last syncpt */
unsigned long flags;
/* push dirty metapages out to disk */
- list_for_each_entry(sbi, &log->sb_list, log_list) {
- filemap_flush(sbi->ipbmap->i_mapping);
- filemap_flush(sbi->ipimap->i_mapping);
- filemap_flush(sbi->direct_inode->i_mapping);
- }
+ if (hard_sync)
+ list_for_each_entry(sbi, &log->sb_list, log_list) {
+ filemap_fdatawrite(sbi->ipbmap->i_mapping);
+ filemap_fdatawrite(sbi->ipimap->i_mapping);
+ filemap_fdatawrite(sbi->direct_inode->i_mapping);
+ }
+ else
+ list_for_each_entry(sbi, &log->sb_list, log_list) {
+ filemap_flush(sbi->ipbmap->i_mapping);
+ filemap_flush(sbi->ipimap->i_mapping);
+ filemap_flush(sbi->direct_inode->i_mapping);
+ }
/*
* forward syncpt
/* next syncpt trigger = written + more */
log->nextsync = written + more;
- /* return if lmLogSync() from outside of transaction, e.g., sync() */
- if (nosyncwait)
- return lsn;
-
/* if number of bytes written from last sync point is more
* than 1/4 of the log size, stop new transactions from
* starting until all current transactions are completed
*
* FUNCTION: write log SYNCPT record for specified log
*
- * PARAMETERS: log - log structure
+ * PARAMETERS: log - log structure
+ * hard_sync - set to 1 to force metadata to be written
*/
-void jfs_syncpt(struct jfs_log *log)
+void jfs_syncpt(struct jfs_log *log, int hard_sync)
{ LOG_LOCK(log);
- lmLogSync(log, 1);
+ lmLogSync(log, hard_sync);
LOG_UNLOCK(log);
}
extern int lmGroupCommit(struct jfs_log *, struct tblock *);
extern int jfsIOWait(void *);
extern void jfs_flush_journal(struct jfs_log * log, int wait);
-extern void jfs_syncpt(struct jfs_log *log);
+extern void jfs_syncpt(struct jfs_log *log, int hard_sync);
#endif /* _H_JFS_LOGMGR */
* synchronize with logsync barrier
*/
if (test_bit(log_SYNCBARRIER, &log->flag)) {
+ TXN_UNLOCK();
+
+ /* write dirty metadata & forward log syncpt */
+ jfs_syncpt(log, 1);
+
jfs_info("log barrier off: 0x%x", log->lsn);
/* enable new transactions start */
/* wakeup all waitors for logsync barrier */
TXN_WAKEUP(&log->syncwait);
- TXN_UNLOCK();
-
- /* forward log syncpt */
- jfs_syncpt(log);
-
goto wakeup;
}
}
/* only anonymous txn.
* Remove from anon_list
*/
+ TXN_LOCK();
list_del_init(&jfs_ip->anon_inode_list);
+ TXN_UNLOCK();
}
jfs_ip->atlhead = tlck->next;
} else {
{
struct jfs_inode_info *ji = JFS_IP(inode);
+ BUG_ON(!list_empty(&ji->anon_inode_list));
+
spin_lock_irq(&ji->ag_lock);
if (ji->active_ag != -1) {
struct bmap *bmap = JFS_SBI(inode->i_sb)->bmap;
/* log == NULL indicates read-only mount */
if (log) {
jfs_flush_journal(log, wait);
- jfs_syncpt(log);
+ jfs_syncpt(log, 0);
}
return 0;
error = vfs_rename_other(old_dir,old_dentry,new_dir,new_dentry);
if (!error) {
const char *new_name = old_dentry->d_name.name;
- fsnotify_move(old_dir, new_dir, old_name, new_name, is_dir, new_dentry->d_inode);
+ fsnotify_move(old_dir, new_dir, old_name, new_name, is_dir,
+ new_dentry->d_inode, old_dentry->d_inode);
}
fsnotify_oldname_free(old_name);
nfs_wb_all(inode);
}
error = NFS_PROTO(inode)->setattr(dentry, &fattr, attr);
- if (error == 0) {
+ if (error == 0)
nfs_refresh_inode(inode, &fattr);
+ nfs_end_data_update(inode);
+ unlock_kernel();
+ return error;
+}
+
+/**
+ * nfs_setattr_update_inode - Update inode metadata after a setattr call.
+ * @inode: pointer to struct inode
+ * @attr: pointer to struct iattr
+ *
+ * Note: we do this in the *proc.c in order to ensure that
+ * it works for things like exclusive creates too.
+ */
+void nfs_setattr_update_inode(struct inode *inode, struct iattr *attr)
+{
+ if ((attr->ia_valid & (ATTR_MODE|ATTR_UID|ATTR_GID)) != 0) {
if ((attr->ia_valid & ATTR_MODE) != 0) {
- int mode;
- mode = inode->i_mode & ~S_IALLUGO;
- mode |= attr->ia_mode & S_IALLUGO;
+ int mode = attr->ia_mode & S_IALLUGO;
+ mode |= inode->i_mode & ~S_IALLUGO;
inode->i_mode = mode;
}
if ((attr->ia_valid & ATTR_UID) != 0)
inode->i_uid = attr->ia_uid;
if ((attr->ia_valid & ATTR_GID) != 0)
inode->i_gid = attr->ia_gid;
- if ((attr->ia_valid & ATTR_SIZE) != 0) {
- inode->i_size = attr->ia_size;
- vmtruncate(inode, attr->ia_size);
- }
- }
- if ((attr->ia_valid & (ATTR_MODE|ATTR_UID|ATTR_GID)) != 0)
NFS_FLAGS(inode) |= NFS_INO_INVALID_ACCESS|NFS_INO_INVALID_ACL;
- nfs_end_data_update(inode);
- unlock_kernel();
- return error;
+ }
+ if ((attr->ia_valid & ATTR_SIZE) != 0) {
+ inode->i_size = attr->ia_size;
+ vmtruncate(inode, attr->ia_size);
+ }
}
/*
dprintk("NFS call setattr\n");
fattr->valid = 0;
status = rpc_call(NFS_CLIENT(inode), NFS3PROC_SETATTR, &arg, fattr, 0);
+ if (status == 0)
+ nfs_setattr_update_inode(inode, sattr);
dprintk("NFS reply setattr: %d\n", status);
return status;
}
* not sure this buys us anything (and I'd have
* to revamp the NFSv3 XDR code) */
status = nfs3_proc_setattr(dentry, &fattr, sattr);
+ if (status == 0)
+ nfs_setattr_update_inode(dentry->d_inode, sattr);
nfs_refresh_inode(dentry->d_inode, &fattr);
dprintk("NFS reply setattr (post-create): %d\n", status);
}
.rpc_argp = &arg,
.rpc_resp = &res,
};
+ int status;
fattr->valid = 0;
} else
memcpy(&arg.stateid, &zero_stateid, sizeof(arg.stateid));
- return rpc_call_sync(server->client, &msg, 0);
+ status = rpc_call_sync(server->client, &msg, 0);
+ return status;
}
static int nfs4_do_setattr(struct nfs_server *server, struct nfs_fattr *fattr,
status = nfs4_do_setattr(NFS_SERVER(inode), fattr,
NFS_FH(inode), sattr, state);
+ if (status == 0)
+ nfs_setattr_update_inode(inode, sattr);
if (state != NULL)
nfs4_close_state(state, FMODE_WRITE);
put_rpccred(cred);
struct nfs_fattr fattr;
status = nfs4_do_setattr(NFS_SERVER(dir), &fattr,
NFS_FH(state->inode), sattr, state);
- if (status == 0)
+ if (status == 0) {
+ nfs_setattr_update_inode(state->inode, sattr);
goto out;
+ }
} else if (flags != 0)
goto out;
nfs4_close_state(state, flags);
dprintk("NFS call setattr\n");
fattr->valid = 0;
status = rpc_call(NFS_CLIENT(inode), NFSPROC_SETATTR, &arg, fattr, 0);
+ if (status == 0)
+ nfs_setattr_update_inode(inode, sattr);
dprintk("NFS reply setattr: %d\n", status);
return status;
}
if (xdr_decode_word(buf, base, &entries) ||
entries > NFS_ACL_MAX_ENTRIES)
return -EINVAL;
+ nfsacl_desc.desc.array_maxlen = entries;
err = xdr_decode_array2(buf, base + 4, &nfsacl_desc.desc);
if (err)
return err;
fact that the vfs and ntfs inodes are one struct in memory to find
the ntfs inode in memory if present. Also, the ntfs inode has its
own locking so it does not matter if the vfs inode is locked.
+ - Fix bug in mft record writing where we forgot to set the device in
+ the buffers when mapping them after the VM had discarded them
+ Thanks to Martin MOKREJŠ for the bug report.
2.1.22 - Many bug and race fixes and error handling improvements.
LCN lcn;
unsigned int vcn_ofs;
+ bh->b_bdev = vol->sb->s_bdev;
/* Obtain the vcn and offset of the current block. */
vcn = ((VCN)mft_no << vol->mft_record_size_bits) +
(block_start - m_start);
LCN lcn;
unsigned int vcn_ofs;
+ bh->b_bdev = vol->sb->s_bdev;
/* Obtain the vcn and offset of the current block. */
vcn = ((VCN)ni->mft_no << vol->mft_record_size_bits) +
(block_start - m_start);
*/
inode->i_uid = current->fsuid;
inode->i_mode = mode;
+ /* Make inode invalid - just in case we are going to drop it before
+ * the initialization happens */
+ INODE_PKEY(inode)->k_objectid = 0;
if (dir->i_mode & S_ISGID) {
inode->i_gid = dir->i_gid;
* Changelog:
* 11-Sep-2004 BJD Created file
* 21-Sep-2004 BJD Updated port info
+ * 09-Aug-2005 BJD Renamed s3c2410_report_oc s3c2410_usb_report_oc
*/
#ifndef __ASM_ARCH_USBCONTROL_H
void (*report_oc)(struct s3c2410_hcd_info *, int ports);
};
-static void inline s3c2410_report_oc(struct s3c2410_hcd_info *info, int ports)
+static void inline s3c2410_usb_report_oc(struct s3c2410_hcd_info *info, int ports)
{
if (info->report_oc != NULL) {
(info->report_oc)(info, ports);
/*
* - extended small page/tiny page
*/
+#define PTE_EXT_XN (1 << 0) /* v6 */
#define PTE_EXT_AP_MASK (3 << 4)
+#define PTE_EXT_AP0 (1 << 4)
+#define PTE_EXT_AP1 (2 << 4)
#define PTE_EXT_AP_UNO_SRO (0 << 4)
-#define PTE_EXT_AP_UNO_SRW (1 << 4)
-#define PTE_EXT_AP_URO_SRW (2 << 4)
-#define PTE_EXT_AP_URW_SRW (3 << 4)
+#define PTE_EXT_AP_UNO_SRW (PTE_EXT_AP0)
+#define PTE_EXT_AP_URO_SRW (PTE_EXT_AP1)
+#define PTE_EXT_AP_URW_SRW (PTE_EXT_AP1|PTE_EXT_AP0)
#define PTE_EXT_TEX(x) ((x) << 6) /* v5 */
+#define PTE_EXT_APX (1 << 9) /* v6 */
+#define PTE_EXT_SHARED (1 << 10) /* v6 */
+#define PTE_EXT_NG (1 << 11) /* v6 */
/*
* - small page
#define L_PTE_WRITE (1 << 5)
#define L_PTE_EXEC (1 << 6)
#define L_PTE_DIRTY (1 << 7)
+#define L_PTE_SHARED (1 << 10) /* shared between CPUs (v6) */
+#define L_PTE_ASID (1 << 11) /* non-global (use ASID, v6) */
#ifndef __ASSEMBLY__
#define pcibios_scan_all_fns(a, b) 0
extern unsigned long pci_mem_start;
-#define PCIBIOS_MIN_IO 0x4000
+#define PCIBIOS_MIN_IO 0x1000
#define PCIBIOS_MIN_MEM (pci_mem_start)
+#define PCIBIOS_MIN_CARDBUS_IO 0x4000
+
void pcibios_config_init(void);
struct pci_bus * pcibios_scan_root(int bus);
};
#define desc_empty(desc) \
- (!((desc)->a + (desc)->b))
+ (!((desc)->a | (desc)->b))
#define desc_equal(desc1, desc2) \
(((desc1)->a == (desc2)->a) && ((desc1)->b == (desc2)->b))
#ifndef _LPARMAP_H
#define _LPARMAP_H
+#ifndef __ASSEMBLY__
+
#include <asm/types.h>
/*
} xRanges[HvRangesToMap];
};
-extern struct LparMap xLparMap;
+extern const struct LparMap xLparMap;
+
+#endif /* __ASSEMBLY__ */
+
+/* the fixed address where the LparMap exists */
+#define LPARMAP_PHYS 0x7000
#endif /* _LPARMAP_H */
register long __sc7 __asm__ ("r7") = (long) arg4; \
register long __sc0 __asm__ ("r0") = (long) arg5; \
register long __sc1 __asm__ ("r1") = (long) arg6; \
-__asm__ __volatile__ ("trapa #0x15" \
+__asm__ __volatile__ ("trapa #0x16" \
: "=z" (__sc0) \
: "0" (__sc0), "r" (__sc4), "r" (__sc5), "r" (__sc6), "r" (__sc7), \
"r" (__sc3), "r" (__sc1) \
* casting is the right thing, but 32-bit UML can't have 64-bit virtual
* addresses
*/
-#define __pa(virt) to_phys((void *) (unsigned long) virt)
-#define __va(phys) to_virt((unsigned long) phys)
+#define __pa(virt) to_phys((void *) (unsigned long) (virt))
+#define __va(phys) to_virt((unsigned long) (phys))
#define page_to_pfn(page) ((page) - mem_map)
#define pfn_to_page(pfn) (mem_map + (pfn))
extern int no_iommu, force_iommu;
extern unsigned long pci_mem_start;
-#define PCIBIOS_MIN_IO 0x4000
+#define PCIBIOS_MIN_IO 0x1000
#define PCIBIOS_MIN_MEM (pci_mem_start)
+#define PCIBIOS_MIN_CARDBUS_IO 0x4000
+
void pcibios_config_init(void);
struct pci_bus * pcibios_scan_root(int bus);
extern int (*pci_config_read)(int seg, int bus, int dev, int fn, int reg, int len, u32 *value);
#define ID_MASK 0x00200000
#define desc_empty(desc) \
- (!((desc)->a + (desc)->b))
+ (!((desc)->a | (desc)->b))
#define desc_equal(desc1, desc2) \
(((desc1)->a == (desc2)->a) && ((desc1)->b == (desc2)->b))
*/
static inline void fsnotify_move(struct inode *old_dir, struct inode *new_dir,
const char *old_name, const char *new_name,
- int isdir, struct inode *target)
+ int isdir, struct inode *target, struct inode *source)
{
u32 cookie = inotify_get_cookie();
inotify_inode_queue_event(target, IN_DELETE_SELF, 0, NULL);
inotify_inode_is_dead(target);
}
+
+ if (source) {
+ inotify_inode_queue_event(source, IN_MOVE_SELF, 0, NULL);
+ }
}
/*
#define ide_id_has_flush_cache_ext(id) \
(((id)->cfs_enable_2 & 0x2400) == 0x2400)
+static inline int hwif_to_node(ide_hwif_t *hwif)
+{
+ struct pci_dev *dev = hwif->pci_dev;
+ return dev ? pcibus_to_node(dev->bus) : -1;
+}
+
#endif /* _IDE_H */
#define IN_CREATE 0x00000100 /* Subfile was created */
#define IN_DELETE 0x00000200 /* Subfile was deleted */
#define IN_DELETE_SELF 0x00000400 /* Self was deleted */
+#define IN_MOVE_SELF 0x00000800 /* Self was moved */
/* the following are legal events. they are sent as needed to any watch */
#define IN_UNMOUNT 0x00002000 /* Backing fs was unmounted */
*/
#define IN_ALL_EVENTS (IN_ACCESS | IN_MODIFY | IN_ATTRIB | IN_CLOSE_WRITE | \
IN_CLOSE_NOWRITE | IN_OPEN | IN_MOVED_FROM | \
- IN_MOVED_TO | IN_DELETE | IN_CREATE | IN_DELETE_SELF)
+ IN_MOVED_TO | IN_DELETE | IN_CREATE | IN_DELETE_SELF | \
+ IN_MOVE_SELF)
#ifdef __KERNEL__
#include <linux/netdevice.h>
#include <linux/interrupt.h>
+#include <linux/rcupdate.h>
#include <linux/list.h>
struct netpoll;
struct netpoll_info {
spinlock_t poll_lock;
int poll_owner;
+ int tries;
int rx_flags;
spinlock_t rx_lock;
struct netpoll *rx_np; /* netpoll that registered an rx_hook */
return ret;
}
-static inline void netpoll_poll_lock(struct net_device *dev)
+static inline void *netpoll_poll_lock(struct net_device *dev)
{
+ rcu_read_lock(); /* deal with race on ->npinfo */
if (dev->npinfo) {
spin_lock(&dev->npinfo->poll_lock);
dev->npinfo->poll_owner = smp_processor_id();
+ return dev->npinfo;
}
+ return NULL;
}
-static inline void netpoll_poll_unlock(struct net_device *dev)
+static inline void netpoll_poll_unlock(void *have)
{
- if (dev->npinfo) {
- dev->npinfo->poll_owner = -1;
- spin_unlock(&dev->npinfo->poll_lock);
+ struct netpoll_info *npi = have;
+
+ if (npi) {
+ npi->poll_owner = -1;
+ spin_unlock(&npi->poll_lock);
}
+ rcu_read_unlock();
}
#else
#define netpoll_rx(a) 0
-#define netpoll_poll_lock(a)
+#define netpoll_poll_lock(a) 0
#define netpoll_poll_unlock(a)
#endif
extern int __nfs_revalidate_inode(struct nfs_server *, struct inode *);
extern void nfs_revalidate_mapping(struct inode *inode, struct address_space *mapping);
extern int nfs_setattr(struct dentry *, struct iattr *);
+extern void nfs_setattr_update_inode(struct inode *inode, struct iattr *attr);
extern void nfs_begin_attr_update(struct inode *);
extern void nfs_end_attr_update(struct inode *);
extern void nfs_begin_data_update(struct inode *);
/* keep track of device state */
unsigned int is_enabled:1; /* pci_enable_device has been called */
unsigned int is_busmaster:1; /* device is busmaster */
-
+ unsigned int no_msi:1; /* device may not use msi */
+
u32 saved_config_space[16]; /* config space saved at suspend time */
struct bin_attribute *rom_attr; /* attribute descriptor for sysfs ROM entry */
int rom_attr_enabled; /* has display of the rom attribute been enabled? */
#define PCI_VENDOR_ID_INTEL 0x8086
#define PCI_DEVICE_ID_INTEL_EESSC 0x0008
#define PCI_DEVICE_ID_INTEL_21145 0x0039
+#define PCI_DEVICE_ID_INTEL_PXHD_0 0x0320
+#define PCI_DEVICE_ID_INTEL_PXHD_1 0x0321
+#define PCI_DEVICE_ID_INTEL_PXH_0 0x0329
+#define PCI_DEVICE_ID_INTEL_PXH_1 0x032A
+#define PCI_DEVICE_ID_INTEL_PXHV 0x032C
#define PCI_DEVICE_ID_INTEL_82375 0x0482
#define PCI_DEVICE_ID_INTEL_82424 0x0483
#define PCI_DEVICE_ID_INTEL_82378 0x0484
nohdr:1;
/* 3 bits spare */
__u8 pkt_type;
- __u16 protocol;
+ __be16 protocol;
void (*destructor)(struct sk_buff *skb);
#ifdef CONFIG_NETFILTER
struct xdr_array2_desc {
unsigned int elem_size;
unsigned int array_len;
+ unsigned int array_maxlen;
xdr_xcode_elem_t xcode;
};
struct transport_container target_attrs;
struct transport_container device_attrs;
+ /*
+ * If set, call target_parent prior to allocating a scsi_target,
+ * so we get the appropriate parent for the target. This function
+ * is required for transports like FC and iSCSI that do not put the
+ * scsi_target under scsi_host.
+ */
+ struct device *(*target_parent)(struct Scsi_Host *, int, uint);
+
/* The size of the specific transport attribute structure (a
* space of this size will be left at the end of the
* scsi_* structure */
* to continue to serve a useful existence. Next time it's released,
* we will get notified again, if it still has 'notify_on_release' set.
*
- * Note final arg to call_usermodehelper() is 0 - that means
- * don't wait. Since we are holding the global cpuset_sem here,
- * and we are asking another thread (started from keventd) to rmdir a
- * cpuset, we can't wait - or we'd deadlock with the removing thread
- * on cpuset_sem.
+ * The final arg to call_usermodehelper() is 0, which means don't
+ * wait. The separate /sbin/cpuset_release_agent task is forked by
+ * call_usermodehelper(), then control in this thread returns here,
+ * without waiting for the release agent task. We don't bother to
+ * wait because the caller of this routine has no use for the exit
+ * status of the /sbin/cpuset_release_agent task, so no sense holding
+ * our caller up for that.
+ *
+ * The simple act of forking that task might require more memory,
+ * which might need cpuset_sem. So this routine must be called while
+ * cpuset_sem is not held, to avoid a possible deadlock. See also
+ * comments for check_for_release(), below.
*/
-static int cpuset_release_agent(char *cpuset_str)
+static void cpuset_release_agent(const char *pathbuf)
{
char *argv[3], *envp[3];
int i;
+ if (!pathbuf)
+ return;
+
i = 0;
argv[i++] = "/sbin/cpuset_release_agent";
- argv[i++] = cpuset_str;
+ argv[i++] = (char *)pathbuf;
argv[i] = NULL;
i = 0;
envp[i++] = "PATH=/sbin:/bin:/usr/sbin:/usr/bin";
envp[i] = NULL;
- return call_usermodehelper(argv[0], argv, envp, 0);
+ call_usermodehelper(argv[0], argv, envp, 0);
+ kfree(pathbuf);
}
/*
* Either cs->count of using tasks transitioned to zero, or the
* cs->children list of child cpusets just became empty. If this
* cs is notify_on_release() and now both the user count is zero and
- * the list of children is empty, send notice to user land.
+ * the list of children is empty, prepare cpuset path in a kmalloc'd
+ * buffer, to be returned via ppathbuf, so that the caller can invoke
+ * cpuset_release_agent() with it later on, once cpuset_sem is dropped.
+ * Call here with cpuset_sem held.
+ *
+ * This check_for_release() routine is responsible for kmalloc'ing
+ * pathbuf. The above cpuset_release_agent() is responsible for
+ * kfree'ing pathbuf. The caller of these routines is responsible
+ * for providing a pathbuf pointer, initialized to NULL, then
+ * calling check_for_release() with cpuset_sem held and the address
+ * of the pathbuf pointer, then dropping cpuset_sem, then calling
+ * cpuset_release_agent() with pathbuf, as set by check_for_release().
*/
-static void check_for_release(struct cpuset *cs)
+static void check_for_release(struct cpuset *cs, char **ppathbuf)
{
if (notify_on_release(cs) && atomic_read(&cs->count) == 0 &&
list_empty(&cs->children)) {
if (!buf)
return;
if (cpuset_path(cs, buf, PAGE_SIZE) < 0)
- goto out;
- cpuset_release_agent(buf);
-out:
- kfree(buf);
+ kfree(buf);
+ else
+ *ppathbuf = buf;
}
}
return 0;
}
-static int attach_task(struct cpuset *cs, char *buf)
+static int attach_task(struct cpuset *cs, char *pidbuf, char **ppathbuf)
{
pid_t pid;
struct task_struct *tsk;
struct cpuset *oldcs;
cpumask_t cpus;
- if (sscanf(buf, "%d", &pid) != 1)
+ if (sscanf(pidbuf, "%d", &pid) != 1)
return -EIO;
if (cpus_empty(cs->cpus_allowed) || nodes_empty(cs->mems_allowed))
return -ENOSPC;
put_task_struct(tsk);
if (atomic_dec_and_test(&oldcs->count))
- check_for_release(oldcs);
+ check_for_release(oldcs, ppathbuf);
return 0;
}
struct cftype *cft = __d_cft(file->f_dentry);
cpuset_filetype_t type = cft->private;
char *buffer;
+ char *pathbuf = NULL;
int retval = 0;
/* Crude upper limit on largest legitimate cpulist user might write. */
retval = update_flag(CS_NOTIFY_ON_RELEASE, cs, buffer);
break;
case FILE_TASKLIST:
- retval = attach_task(cs, buffer);
+ retval = attach_task(cs, buffer, &pathbuf);
break;
default:
retval = -EINVAL;
retval = nbytes;
out2:
up(&cpuset_sem);
+ cpuset_release_agent(pathbuf);
out1:
kfree(buffer);
return retval;
struct cpuset *cs = dentry->d_fsdata;
struct dentry *d;
struct cpuset *parent;
+ char *pathbuf = NULL;
/* the vfs holds both inode->i_sem already */
update_cpu_domains(cs);
list_del(&cs->sibling); /* delete my sibling from parent->children */
if (list_empty(&parent->children))
- check_for_release(parent);
+ check_for_release(parent, &pathbuf);
spin_lock(&cs->dentry->d_lock);
d = dget(cs->dentry);
cs->dentry = NULL;
cpuset_d_remove_dir(d);
dput(d);
up(&cpuset_sem);
+ cpuset_release_agent(pathbuf);
return 0;
}
task_unlock(tsk);
if (notify_on_release(cs)) {
+ char *pathbuf = NULL;
+
down(&cpuset_sem);
if (atomic_dec_and_test(&cs->count))
- check_for_release(cs);
+ check_for_release(cs, &pathbuf);
up(&cpuset_sem);
+ cpuset_release_agent(pathbuf);
} else {
atomic_dec(&cs->count);
}
struct workqueue_struct *wq;
struct task_struct *p;
- BUG_ON(strlen(name) > 10);
-
wq = kmalloc(sizeof(*wq), GFP_KERNEL);
if (!wq)
return NULL;
} else
kern_msg->msg_name = NULL;
- if(kern_msg->msg_iovlen > UIO_FASTIOV) {
- kern_iov = kmalloc(kern_msg->msg_iovlen * sizeof(struct iovec),
- GFP_KERNEL);
- if(!kern_iov)
- return -ENOMEM;
- }
-
tot_len = iov_from_user_compat_to_kern(kern_iov,
(struct compat_iovec __user *)kern_msg->msg_iov,
kern_msg->msg_iovlen);
if(tot_len >= 0)
kern_msg->msg_iov = kern_iov;
- else if(kern_msg->msg_iovlen > UIO_FASTIOV)
- kfree(kern_iov);
return tot_len;
}
struct softnet_data *queue = &__get_cpu_var(softnet_data);
unsigned long start_time = jiffies;
int budget = netdev_budget;
-
+ void *have;
+
local_irq_disable();
while (!list_empty(&queue->poll_list)) {
dev = list_entry(queue->poll_list.next,
struct net_device, poll_list);
- netpoll_poll_lock(dev);
+ have = netpoll_poll_lock(dev);
if (dev->quota <= 0 || dev->poll(dev, &budget)) {
- netpoll_poll_unlock(dev);
+ netpoll_poll_unlock(have);
local_irq_disable();
list_del(&dev->poll_list);
list_add_tail(&dev->poll_list, &queue->poll_list);
else
dev->quota = dev->weight;
} else {
- netpoll_poll_unlock(dev);
+ netpoll_poll_unlock(have);
dev_put(dev);
local_irq_disable();
}
#define MAX_UDP_CHUNK 1460
#define MAX_SKBS 32
#define MAX_QUEUE_DEPTH (MAX_SKBS / 2)
+#define MAX_RETRIES 20000
static DEFINE_SPINLOCK(skb_list_lock);
static int nr_skbs;
int status;
struct netpoll_info *npinfo;
-repeat:
- if(!np || !np->dev || !netif_running(np->dev)) {
+ if (!np || !np->dev || !netif_running(np->dev)) {
__kfree_skb(skb);
return;
}
- /* avoid recursion */
npinfo = np->dev->npinfo;
+
+ /* avoid recursion */
if (npinfo->poll_owner == smp_processor_id() ||
np->dev->xmit_lock_owner == smp_processor_id()) {
if (np->drop)
return;
}
- spin_lock(&np->dev->xmit_lock);
- np->dev->xmit_lock_owner = smp_processor_id();
+ do {
+ npinfo->tries--;
+ spin_lock(&np->dev->xmit_lock);
+ np->dev->xmit_lock_owner = smp_processor_id();
- /*
- * network drivers do not expect to be called if the queue is
- * stopped.
- */
- if (netif_queue_stopped(np->dev)) {
+ /*
+ * network drivers do not expect to be called if the queue is
+ * stopped.
+ */
+ if (netif_queue_stopped(np->dev)) {
+ np->dev->xmit_lock_owner = -1;
+ spin_unlock(&np->dev->xmit_lock);
+ netpoll_poll(np);
+ udelay(50);
+ continue;
+ }
+
+ status = np->dev->hard_start_xmit(skb, np->dev);
np->dev->xmit_lock_owner = -1;
spin_unlock(&np->dev->xmit_lock);
- netpoll_poll(np);
- goto repeat;
- }
-
- status = np->dev->hard_start_xmit(skb, np->dev);
- np->dev->xmit_lock_owner = -1;
- spin_unlock(&np->dev->xmit_lock);
+ /* success */
+ if(!status) {
+ npinfo->tries = MAX_RETRIES; /* reset */
+ return;
+ }
- /* transmit busy */
- if(status) {
+ /* transmit busy */
netpoll_poll(np);
- goto repeat;
- }
+ udelay(50);
+ } while (npinfo->tries > 0);
}
void netpoll_send_udp(struct netpoll *np, const char *msg, int len)
unsigned char *arp_ptr;
int size, type = ARPOP_REPLY, ptype = ETH_P_ARP;
u32 sip, tip;
- unsigned long flags;
struct sk_buff *send_skb;
struct netpoll *np = NULL;
- spin_lock_irqsave(&npinfo->rx_lock, flags);
if (npinfo->rx_np && npinfo->rx_np->dev == skb->dev)
np = npinfo->rx_np;
- spin_unlock_irqrestore(&npinfo->rx_lock, flags);
-
if (!np)
return;
if (!npinfo)
goto release;
+ npinfo->rx_flags = 0;
npinfo->rx_np = NULL;
npinfo->poll_lock = SPIN_LOCK_UNLOCKED;
npinfo->poll_owner = -1;
+ npinfo->tries = MAX_RETRIES;
npinfo->rx_lock = SPIN_LOCK_UNLOCKED;
} else
npinfo = ndev->npinfo;
npinfo->rx_np = np;
spin_unlock_irqrestore(&npinfo->rx_lock, flags);
}
+
+ /* fill up the skb queue */
+ refill_skbs();
+
/* last thing to do is link it to the net device structure */
ndev->npinfo = npinfo;
+ /* avoid racing with NAPI reading npinfo */
+ synchronize_rcu();
+
return 0;
release:
return mss_now;
}
-static int dn_error(struct sock *sk, int flags, int err)
-{
- if (err == -EPIPE)
- err = sock_error(sk) ? : -EPIPE;
- if (err == -EPIPE && !(flags & MSG_NOSIGNAL))
- send_sig(SIGPIPE, current, 0);
- return err;
-}
-
static int dn_sendmsg(struct kiocb *iocb, struct socket *sock,
struct msghdr *msg, size_t size)
{
return sent ? sent : err;
out_err:
- err = dn_error(sk, flags, err);
+ err = sk_stream_error(sk, flags, err);
release_sock(sk);
return err;
}
if (skb->len > cur_mss) {
int old_factor = tcp_skb_pcount(skb);
- int new_factor;
+ int diff;
if (tcp_fragment(sk, skb, cur_mss, cur_mss))
return -ENOMEM; /* We'll try again later. */
/* New SKB created, account for it. */
- new_factor = tcp_skb_pcount(skb);
- tp->packets_out -= old_factor - new_factor;
- tp->packets_out += tcp_skb_pcount(skb->next);
+ diff = old_factor - tcp_skb_pcount(skb) -
+ tcp_skb_pcount(skb->next);
+ tp->packets_out -= diff;
+
+ if (diff > 0) {
+ tp->fackets_out -= diff;
+ if ((int)tp->fackets_out < 0)
+ tp->fackets_out = 0;
+ }
}
/* Collapse two adjacent packets if worthwhile and we can. */
}
if (skb->stamp.tv_sec == 0) {
skb->stamp.tv_sec = xtime.tv_sec;
- skb->stamp.tv_usec = xtime.tv_nsec * 1000;
+ skb->stamp.tv_usec = xtime.tv_nsec / NSEC_PER_USEC;
/* Don't enable netstamp, sunrpc doesn't
need that much accuracy */
}
return -EINVAL;
} else {
if (xdr_decode_word(buf, base, &desc->array_len) != 0 ||
+ desc->array_len > desc->array_maxlen ||
(unsigned long) base + 4 + desc->array_len *
desc->elem_size > buf->len)
return -EINVAL;
OSDN Git Service
