[pf3gnuchains/gcc-fork.git] / gcc / doc / invoke.texi

@c Copyright (C) 1988, 1989, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999,
@c 2000, 2001, 2002, 2003 Free Software Foundation, Inc.
@c This is part of the GCC manual.
@c For copying conditions, see the file gcc.texi.

@ignore
@c man begin COPYRIGHT
Copyright @copyright{} 1988, 1989, 1992, 1993, 1994, 1995, 1996, 1997,
1998, 1999, 2000, 2001, 2002, 2003 Free Software Foundation, Inc.

Permission is granted to copy, distribute and/or modify this document
under the terms of the GNU Free Documentation License, Version 1.2 or
any later version published by the Free Software Foundation; with the
Invariant Sections being ``GNU General Public License'' and ``Funding
Free Software'', the Front-Cover texts being (a) (see below), and with
the Back-Cover Texts being (b) (see below).  A copy of the license is
included in the gfdl(7) man page.

(a) The FSF's Front-Cover Text is:

     A GNU Manual

(b) The FSF's Back-Cover Text is:

     You have freedom to copy and modify this GNU Manual, like GNU
     software.  Copies published by the Free Software Foundation raise
     funds for GNU development.
@c man end
@c Set file name and title for the man page.
@setfilename gcc
@settitle GNU project C and C++ compiler
@c man begin SYNOPSIS
gcc [@option{-c}|@option{-S}|@option{-E}] [@option{-std=}@var{standard}]
    [@option{-g}] [@option{-pg}] [@option{-O}@var{level}]
    [@option{-W}@var{warn}@dots{}] [@option{-pedantic}]
    [@option{-I}@var{dir}@dots{}] [@option{-L}@var{dir}@dots{}]
    [@option{-D}@var{macro}[=@var{defn}]@dots{}] [@option{-U}@var{macro}]
    [@option{-f}@var{option}@dots{}] [@option{-m}@var{machine-option}@dots{}]
    [@option{-o} @var{outfile}] @var{infile}@dots{}

Only the most useful options are listed here; see below for the
remainder.  @samp{g++} accepts mostly the same options as @samp{gcc}.
@c man end
@c man begin SEEALSO
gpl(7), gfdl(7), fsf-funding(7),
cpp(1), gcov(1), g77(1), as(1), ld(1), gdb(1), adb(1), dbx(1), sdb(1)
and the Info entries for @file{gcc}, @file{cpp}, @file{g77}, @file{as},
@file{ld}, @file{binutils} and @file{gdb}.
@c man end
@c man begin BUGS
For instructions on reporting bugs, see
@w{@uref{http://gcc.gnu.org/bugs.html}}.  Use of the @command{gccbug}
script to report bugs is recommended.
@c man end
@c man begin AUTHOR
See the Info entry for @command{gcc}, or
@w{@uref{http://gcc.gnu.org/onlinedocs/gcc/Contributors.html}},
for contributors to GCC@.
@c man end
@end ignore

@node Invoking GCC
@chapter GCC Command Options
@cindex GCC command options
@cindex command options
@cindex options, GCC command

@c man begin DESCRIPTION
When you invoke GCC, it normally does preprocessing, compilation,
assembly and linking.  The ``overall options'' allow you to stop this
process at an intermediate stage.  For example, the @option{-c} option
says not to run the linker.  Then the output consists of object files
output by the assembler.

Other options are passed on to one stage of processing.  Some options
control the preprocessor and others the compiler itself.  Yet other
options control the assembler and linker; most of these are not
documented here, since you rarely need to use any of them.

@cindex C compilation options
Most of the command line options that you can use with GCC are useful
for C programs; when an option is only useful with another language
(usually C++), the explanation says so explicitly.  If the description
for a particular option does not mention a source language, you can use
that option with all supported languages.

@cindex C++ compilation options
@xref{Invoking G++,,Compiling C++ Programs}, for a summary of special
options for compiling C++ programs.

@cindex grouping options
@cindex options, grouping
The @command{gcc} program accepts options and file names as operands.  Many
options have multi-letter names; therefore multiple single-letter options
may @emph{not} be grouped: @option{-dr} is very different from @w{@samp{-d
-r}}.

@cindex order of options
@cindex options, order
You can mix options and other arguments.  For the most part, the order
you use doesn't matter.  Order does matter when you use several options
of the same kind; for example, if you specify @option{-L} more than once,
the directories are searched in the order specified.

Many options have long names starting with @samp{-f} or with
@samp{-W}---for example, @option{-fforce-mem},
@option{-fstrength-reduce}, @option{-Wformat} and so on.  Most of
these have both positive and negative forms; the negative form of
@option{-ffoo} would be @option{-fno-foo}.  This manual documents
only one of these two forms, whichever one is not the default.

@c man end

@xref{Option Index}, for an index to GCC's options.

@menu
* Option Summary::      Brief list of all options, without explanations.
* Overall Options::     Controlling the kind of output:
                        an executable, object files, assembler files,
                        or preprocessed source.
* Invoking G++::        Compiling C++ programs.
* C Dialect Options::   Controlling the variant of C language compiled.
* C++ Dialect Options:: Variations on C++.
* Objective-C Dialect Options:: Variations on Objective-C.
* Language Independent Options:: Controlling how diagnostics should be
                        formatted.
* Warning Options::     How picky should the compiler be?
* Debugging Options::   Symbol tables, measurements, and debugging dumps.
* Optimize Options::    How much optimization?
* Preprocessor Options:: Controlling header files and macro definitions.
                         Also, getting dependency information for Make.
* Assembler Options::   Passing options to the assembler.
* Link Options::        Specifying libraries and so on.
* Directory Options::   Where to find header files and libraries.
                        Where to find the compiler executable files.
* Spec Files::          How to pass switches to sub-processes.
* Target Options::      Running a cross-compiler, or an old version of GCC.
* Submodel Options::    Specifying minor hardware or convention variations,
                        such as 68010 vs 68020.
* Code Gen Options::    Specifying conventions for function calls, data layout
                        and register usage.
* Environment Variables:: Env vars that affect GCC.
* Precompiled Headers:: Compiling a header once, and using it many times.
* Running Protoize::    Automatically adding or removing function prototypes.
@end menu

@c man begin OPTIONS

@node Option Summary
@section Option Summary

Here is a summary of all the options, grouped by type.  Explanations are
in the following sections.

@table @emph
@item Overall Options
@xref{Overall Options,,Options Controlling the Kind of Output}.
@gccoptlist{-c  -S  -E  -o @var{file}  -pipe  -pass-exit-codes  @gol
-x @var{language}  -v  -###  --help  --target-help  --version}

@item C Language Options
@xref{C Dialect Options,,Options Controlling C Dialect}.
@gccoptlist{-ansi  -std=@var{standard}  -aux-info @var{filename} @gol
-fno-asm  -fno-builtin  -fno-builtin-@var{function} @gol
-fhosted  -ffreestanding  -fms-extensions @gol
-trigraphs  -no-integrated-cpp  -traditional  -traditional-cpp @gol
-fallow-single-precision  -fcond-mismatch @gol
-fsigned-bitfields  -fsigned-char @gol
-funsigned-bitfields  -funsigned-char @gol
-fwritable-strings}

@item C++ Language Options
@xref{C++ Dialect Options,,Options Controlling C++ Dialect}.
@gccoptlist{-fabi-version=@var{n}  -fno-access-control  -fcheck-new @gol
-fconserve-space  -fno-const-strings @gol
-fno-elide-constructors @gol
-fno-enforce-eh-specs  -fexternal-templates @gol
-falt-external-templates @gol
-ffor-scope  -fno-for-scope  -fno-gnu-keywords @gol
-fno-implicit-templates @gol
-fno-implicit-inline-templates @gol
-fno-implement-inlines  -fms-extensions @gol
-fno-nonansi-builtins  -fno-operator-names @gol
-fno-optional-diags  -fpermissive @gol
-frepo  -fno-rtti  -fstats  -ftemplate-depth-@var{n} @gol
-fuse-cxa-atexit  -fvtable-gc  -fno-weak  -nostdinc++ @gol
-fno-default-inline  -Wabi  -Wctor-dtor-privacy @gol
-Wnon-virtual-dtor  -Wreorder @gol
-Weffc++  -Wno-deprecated @gol
-Wno-non-template-friend  -Wold-style-cast @gol
-Woverloaded-virtual  -Wno-pmf-conversions @gol
-Wsign-promo  -Wsynth}

@item Objective-C Language Options
@xref{Objective-C Dialect Options,,Options Controlling Objective-C Dialect}.
@gccoptlist{-fconstant-string-class=@var{class-name} @gol
-fgnu-runtime  -fnext-runtime  -gen-decls @gol
-Wno-protocol  -Wselector -Wundeclared-selector}

@item Language Independent Options
@xref{Language Independent Options,,Options to Control Diagnostic Messages Formatting}.
@gccoptlist{-fmessage-length=@var{n}  @gol
-fdiagnostics-show-location=@r{[}once@r{|}every-line@r{]}}

@item Warning Options
@xref{Warning Options,,Options to Request or Suppress Warnings}.
@gccoptlist{-fsyntax-only  -pedantic  -pedantic-errors @gol
-w  -Wextra  -Wall  -Waggregate-return @gol
-Wcast-align  -Wcast-qual  -Wchar-subscripts  -Wcomment @gol
-Wconversion  -Wno-deprecated-declarations @gol
-Wdisabled-optimization  -Wno-div-by-zero  -Werror @gol
-Wfloat-equal  -Wformat  -Wformat=2 @gol
-Wformat-nonliteral  -Wformat-security @gol
-Wimplicit  -Wimplicit-int  @gol
-Wimplicit-function-declaration @gol
-Werror-implicit-function-declaration @gol
-Wimport  -Winline  -Winvalid-pch  -Wno-endif-labels @gol
-Wno-invalid-offsetof @gol
-Wlarger-than-@var{len}  -Wlong-long @gol
-Wmain  -Wmissing-braces @gol
-Wmissing-format-attribute  -Wmissing-noreturn @gol
-Wno-multichar  -Wno-format-extra-args  -Wno-format-y2k @gol
-Wno-import  -Wnonnull  -Wpacked  -Wpadded @gol
-Wparentheses  -Wpointer-arith  -Wredundant-decls @gol
-Wreturn-type  -Wsequence-point  -Wshadow @gol
-Wsign-compare  -Wstrict-aliasing @gol
-Wswitch  -Wswitch-default  -Wswitch-enum @gol
-Wsystem-headers  -Wtrigraphs  -Wundef  -Wuninitialized @gol
-Wunknown-pragmas  -Wunreachable-code @gol
-Wunused  -Wunused-function  -Wunused-label  -Wunused-parameter @gol
-Wunused-value  -Wunused-variable  -Wwrite-strings}

@item C-only Warning Options
@gccoptlist{-Wbad-function-cast  -Wmissing-declarations @gol
-Wmissing-prototypes  -Wnested-externs @gol
-Wstrict-prototypes  -Wtraditional}

@item Debugging Options
@xref{Debugging Options,,Options for Debugging Your Program or GCC}.
@gccoptlist{-d@var{letters}  -dumpspecs  -dumpmachine  -dumpversion @gol
-fdump-unnumbered  -fdump-translation-unit@r{[}-@var{n}@r{]} @gol
-fdump-class-hierarchy@r{[}-@var{n}@r{]} @gol
-fdump-tree-original@r{[}-@var{n}@r{]}  @gol
-fdump-tree-optimized@r{[}-@var{n}@r{]} @gol
-fdump-tree-inlined@r{[}-@var{n}@r{]} @gol
-feliminate-dwarf2-dups -feliminate-unused-debug-types @gol
-fmem-report -fprofile-arcs @gol
-frandom-seed=@var{string} -fsched-verbose=@var{n} @gol
-ftest-coverage  -ftime-report @gol
-g  -g@var{level}  -gcoff  -gdwarf  -gdwarf-1  -gdwarf-1+  -gdwarf-2 @gol
-ggdb  -gstabs  -gstabs+  -gvms  -gxcoff  -gxcoff+ @gol
-p  -pg  -print-file-name=@var{library}  -print-libgcc-file-name @gol
-print-multi-directory  -print-multi-lib @gol
-print-prog-name=@var{program}  -print-search-dirs  -Q @gol
-save-temps  -time}

@item Optimization Options
@xref{Optimize Options,,Options that Control Optimization}.
@gccoptlist{-falign-functions=@var{n}  -falign-jumps=@var{n} @gol
-falign-labels=@var{n}  -falign-loops=@var{n}  @gol
-fbranch-probabilities  -fcaller-saves  -fcprop-registers @gol
-fcse-follow-jumps  -fcse-skip-blocks  -fdata-sections @gol
-fdelayed-branch  -fdelete-null-pointer-checks @gol
-fexpensive-optimizations  -ffast-math  -ffloat-store @gol
-fforce-addr  -fforce-mem  -ffunction-sections @gol
-fgcse  -fgcse-lm  -fgcse-sm  -floop-optimize  -fcrossjumping @gol
-fif-conversion  -fif-conversion2 @gol
-finline-functions  -finline-limit=@var{n}  -fkeep-inline-functions @gol
-fkeep-static-consts  -fmerge-constants  -fmerge-all-constants @gol
-fmove-all-movables  -fnew-ra  -fno-branch-count-reg @gol
-fno-default-inline  -fno-defer-pop @gol
-fno-function-cse  -fno-guess-branch-probability @gol
-fno-inline  -fno-math-errno  -fno-peephole  -fno-peephole2 @gol
-funsafe-math-optimizations  -ffinite-math-only @gol
-fno-trapping-math  -fno-zero-initialized-in-bss @gol
-fomit-frame-pointer  -foptimize-register-move @gol
-foptimize-sibling-calls  -fprefetch-loop-arrays @gol
-freduce-all-givs  -fregmove  -frename-registers @gol
-freorder-blocks  -freorder-functions @gol
-frerun-cse-after-loop  -frerun-loop-opt @gol
-fschedule-insns  -fschedule-insns2 @gol
-fno-sched-interblock  -fno-sched-spec  -fsched-spec-load @gol
-fsched-spec-load-dangerous  -fsched2-use-superblocks @gol
-fsched2-use-traces  -fsignaling-nans @gol
-fsingle-precision-constant  -fssa  -fssa-ccp  -fssa-dce @gol
-fstrength-reduce  -fstrict-aliasing  -ftracer  -fthread-jumps @gol
-funroll-all-loops  -funroll-loops  -fpeel-loops @gol
-funswitch-loops  -fold-unroll-loops  -fold-unroll-all-loops @gol
--param @var{name}=@var{value}
-O  -O0  -O1  -O2  -O3  -Os}

@item Preprocessor Options
@xref{Preprocessor Options,,Options Controlling the Preprocessor}.
@gccoptlist{-A@var{question}=@var{answer} @gol
-A-@var{question}@r{[}=@var{answer}@r{]} @gol
-C  -dD  -dI  -dM  -dN @gol
-D@var{macro}@r{[}=@var{defn}@r{]}  -E  -H @gol
-idirafter @var{dir} @gol
-include @var{file}  -imacros @var{file} @gol
-iprefix @var{file}  -iwithprefix @var{dir} @gol
-iwithprefixbefore @var{dir}  -isystem @var{dir} @gol
-M  -MM  -MF  -MG  -MP  -MQ  -MT  -nostdinc  -P  -remap @gol
-trigraphs  -undef  -U@var{macro}  -Wp,@var{option} @gol
-Xpreprocessor @var{option}}

@item Assembler Option
@xref{Assembler Options,,Passing Options to the Assembler}.
@gccoptlist{-Wa,@var{option}  -Xassembler @var{option}}

@item Linker Options
@xref{Link Options,,Options for Linking}.
@gccoptlist{@var{object-file-name}  -l@var{library} @gol
-nostartfiles  -nodefaultlibs  -nostdlib @gol
-s  -static  -static-libgcc  -shared  -shared-libgcc  -symbolic @gol
-Wl,@var{option}  -Xlinker @var{option} @gol
-u @var{symbol}}

@item Directory Options
@xref{Directory Options,,Options for Directory Search}.
@gccoptlist{-B@var{prefix}  -I@var{dir}  -I-  -L@var{dir}  -specs=@var{file}}

@item Target Options
@c I wrote this xref this way to avoid overfull hbox. -- rms
@xref{Target Options}.
@gccoptlist{-V @var{version}  -b @var{machine}}

@item Machine Dependent Options
@xref{Submodel Options,,Hardware Models and Configurations}.

@emph{M680x0 Options}
@gccoptlist{-m68000  -m68020  -m68020-40  -m68020-60  -m68030  -m68040 @gol
-m68060  -mcpu32  -m5200  -m68881  -mbitfield  -mc68000  -mc68020   @gol
-mnobitfield  -mrtd  -mshort  -msoft-float  -mpcrel @gol
-malign-int  -mstrict-align}

@emph{M68hc1x Options}
@gccoptlist{-m6811  -m6812  -m68hc11  -m68hc12   -m68hcs12 @gol
-mauto-incdec  -minmax  -mlong-calls  -mshort @gol
-msoft-reg-count=@var{count}}

@emph{VAX Options}
@gccoptlist{-mg  -mgnu  -munix}

@emph{SPARC Options}
@gccoptlist{-mcpu=@var{cpu-type} @gol
-mtune=@var{cpu-type} @gol
-mcmodel=@var{code-model} @gol
-m32  -m64 @gol
-mapp-regs  -mbroken-saverestore  -mcypress @gol
-mfaster-structs  -mflat @gol
-mfpu  -mhard-float  -mhard-quad-float @gol
-mimpure-text  -mlive-g0  -mno-app-regs @gol
-mno-faster-structs  -mno-flat  -mno-fpu @gol
-mno-impure-text  -mno-stack-bias  -mno-unaligned-doubles @gol
-msoft-float  -msoft-quad-float  -msparclite  -mstack-bias @gol
-msupersparc  -munaligned-doubles  -mv8}

@emph{ARM Options}
@gccoptlist{-mapcs-frame  -mno-apcs-frame @gol
-mapcs-26  -mapcs-32 @gol
-mapcs-stack-check  -mno-apcs-stack-check @gol
-mapcs-float  -mno-apcs-float @gol
-mapcs-reentrant  -mno-apcs-reentrant @gol
-msched-prolog  -mno-sched-prolog @gol
-mlittle-endian  -mbig-endian  -mwords-little-endian @gol
-malignment-traps  -mno-alignment-traps @gol
-msoft-float  -mhard-float  -mfpe @gol
-mthumb-interwork  -mno-thumb-interwork @gol
-mcpu=@var{name}  -march=@var{name}  -mfpe=@var{name}  @gol
-mstructure-size-boundary=@var{n} @gol
-mabort-on-noreturn @gol
-mlong-calls  -mno-long-calls @gol
-msingle-pic-base  -mno-single-pic-base @gol
-mpic-register=@var{reg} @gol
-mnop-fun-dllimport @gol
-mcirrus-fix-invalid-insns -mno-cirrus-fix-invalid-insns @gol
-mpoke-function-name @gol
-mthumb  -marm @gol
-mtpcs-frame  -mtpcs-leaf-frame @gol
-mcaller-super-interworking  -mcallee-super-interworking}

@emph{MN10200 Options}
@gccoptlist{-mrelax}

@emph{MN10300 Options}
@gccoptlist{-mmult-bug  -mno-mult-bug @gol
-mam33  -mno-am33 @gol
-mno-crt0  -mrelax}

@emph{M32R/D Options}
@gccoptlist{-m32rx  -m32r  -mcode-model=@var{model-type} @gol
-msdata=@var{sdata-type}  -G @var{num}}

@emph{M88K Options}
@gccoptlist{-m88000  -m88100  -m88110  -mbig-pic @gol
-mcheck-zero-division  -mhandle-large-shift @gol
-midentify-revision  -mno-check-zero-division @gol
-mno-ocs-debug-info  -mno-ocs-frame-position @gol
-mno-optimize-arg-area  -mno-serialize-volatile @gol
-mno-underscores  -mocs-debug-info @gol
-mocs-frame-position  -moptimize-arg-area @gol
-mserialize-volatile  -mshort-data-@var{num}  -msvr3 @gol
-msvr4  -mtrap-large-shift  -muse-div-instruction @gol
-mversion-03.00  -mwarn-passed-structs}

@emph{RS/6000 and PowerPC Options}
@gccoptlist{-mcpu=@var{cpu-type} @gol
-mtune=@var{cpu-type} @gol
-mpower  -mno-power  -mpower2  -mno-power2 @gol
-mpowerpc  -mpowerpc64  -mno-powerpc @gol
-maltivec  -mno-altivec @gol
-mpowerpc-gpopt  -mno-powerpc-gpopt @gol
-mpowerpc-gfxopt  -mno-powerpc-gfxopt @gol
-mnew-mnemonics  -mold-mnemonics @gol
-mfull-toc   -mminimal-toc  -mno-fp-in-toc  -mno-sum-in-toc @gol
-m64  -m32  -mxl-call  -mno-xl-call  -mpe @gol
-malign-power  -malign-natural @gol
-msoft-float  -mhard-float  -mmultiple  -mno-multiple @gol
-mstring  -mno-string  -mupdate  -mno-update @gol
-mfused-madd  -mno-fused-madd  -mbit-align  -mno-bit-align @gol
-mstrict-align  -mno-strict-align  -mrelocatable @gol
-mno-relocatable  -mrelocatable-lib  -mno-relocatable-lib @gol
-mtoc  -mno-toc  -mlittle  -mlittle-endian  -mbig  -mbig-endian @gol
-mdynamic-no-pic @gol
-mcall-sysv  -mcall-netbsd @gol
-maix-struct-return  -msvr4-struct-return @gol
-mabi=altivec  -mabi=no-altivec @gol
-mabi=spe  -mabi=no-spe @gol
-misel=yes  -misel=no @gol
-mspe=yes  -mspe=no @gol
-mfloat-gprs=yes  -mfloat-gprs=no @gol
-mprototype  -mno-prototype @gol
-msim  -mmvme  -mads  -myellowknife  -memb  -msdata @gol
-msdata=@var{opt}  -mvxworks  -mwindiss  -G @var{num}  -pthread}

@emph{Darwin Options}
@gccoptlist{-all_load  -allowable_client  -arch  -arch_errors_fatal @gol
-arch_only  -bind_at_load  -bundle  -bundle_loader @gol
-client_name  -compatibility_version  -current_version @gol
-dependency-file  -dylib_file  -dylinker_install_name @gol
-dynamic  -dynamiclib  -exported_symbols_list @gol
-filelist  -flat_namespace  -force_cpusubtype_ALL @gol
-force_flat_namespace  -headerpad_max_install_names @gol
-image_base  -init  -install_name  -keep_private_externs @gol
-multi_module  -multiply_defined  -multiply_defined_unused @gol
-noall_load  -nomultidefs  -noprebind  -noseglinkedit @gol
-pagezero_size  -prebind  -prebind_all_twolevel_modules @gol
-private_bundle  -read_only_relocs  -sectalign @gol
-sectobjectsymbols  -whyload  -seg1addr @gol
-sectcreate  -sectobjectsymbols  -sectorder @gol
-seg_addr_table  -seg_addr_table_filename  -seglinkedit @gol
-segprot  -segs_read_only_addr  -segs_read_write_addr @gol
-single_module  -static  -sub_library  -sub_umbrella @gol
-twolevel_namespace  -umbrella  -undefined @gol
-unexported_symbols_list  -weak_reference_mismatches @gol
-whatsloaded}

@emph{RT Options}
@gccoptlist{-mcall-lib-mul  -mfp-arg-in-fpregs  -mfp-arg-in-gregs @gol
-mfull-fp-blocks  -mhc-struct-return  -min-line-mul @gol
-mminimum-fp-blocks  -mnohc-struct-return}

@emph{MIPS Options}
@gccoptlist{-mabicalls  -march=@var{cpu-type}  -mtune=@var{cpu=type} @gol
-mcpu=@var{cpu-type}  -membedded-data  -muninit-const-in-rodata @gol
-membedded-pic  -mfp32  -mfp64  -mfused-madd  -mno-fused-madd @gol
-mgas  -mgp32  -mgp64 @gol
-mgpopt  -mhalf-pic  -mhard-float  -mint64  -mips1 @gol
-mips2  -mips3  -mips4  -mips32  -mips32r2  -mips64 @gol
-mlong64  -mlong32  -mlong-calls  -mmemcpy @gol
-mmips-as  -mmips-tfile  -mno-abicalls @gol
-mno-embedded-data  -mno-uninit-const-in-rodata @gol
-mno-embedded-pic  -mno-gpopt  -mno-long-calls @gol
-mno-memcpy  -mno-mips-tfile  -mno-rnames  -mno-stats @gol
-mrnames  -msoft-float @gol
-m4650  -msingle-float  -mmad @gol
-EL  -EB  -G @var{num}  -nocpp @gol
-mabi=32  -mabi=n32  -mabi=64  -mabi=eabi  -mabi-fake-default @gol
-mfix7000  -mno-crt0 -mflush-func=@var{func} -mno-flush-func @gol
-mbranch-likely -mno-branch-likely}

@emph{i386 and x86-64 Options}
@gccoptlist{-mtune=@var{cpu-type}  -march=@var{cpu-type} @gol
-mfpmath=@var{unit} @gol
-masm=@var{dialect}  -mno-fancy-math-387 @gol
-mno-fp-ret-in-387  -msoft-float  -msvr3-shlib @gol
-mno-wide-multiply  -mrtd  -malign-double @gol
-mpreferred-stack-boundary=@var{num} @gol
-mmmx  -msse  -msse2  -m3dnow @gol
-mthreads  -mno-align-stringops  -minline-all-stringops @gol
-mpush-args  -maccumulate-outgoing-args  -m128bit-long-double @gol
-m96bit-long-double  -mregparm=@var{num}  -momit-leaf-frame-pointer @gol
-mno-red-zone @gol
-mcmodel=@var{code-model} @gol
-m32  -m64}

@emph{HPPA Options}
@gccoptlist{-march=@var{architecture-type} @gol
-mbig-switch  -mdisable-fpregs  -mdisable-indexing @gol
-mfast-indirect-calls  -mgas  -mgnu-ld   -mhp-ld @gol
-mjump-in-delay -mlinker-opt -mlong-calls @gol
-mlong-load-store  -mno-big-switch  -mno-disable-fpregs @gol
-mno-disable-indexing  -mno-fast-indirect-calls  -mno-gas @gol
-mno-jump-in-delay  -mno-long-load-store @gol
-mno-portable-runtime  -mno-soft-float @gol
-mno-space-regs  -msoft-float  -mpa-risc-1-0 @gol
-mpa-risc-1-1  -mpa-risc-2-0  -mportable-runtime @gol
-mschedule=@var{cpu-type}  -mspace-regs  -msio  -mwsio @gol
-nolibdld  -static  -threads}

@emph{Intel 960 Options}
@gccoptlist{-m@var{cpu-type}  -masm-compat  -mclean-linkage @gol
-mcode-align  -mcomplex-addr  -mleaf-procedures @gol
-mic-compat  -mic2.0-compat  -mic3.0-compat @gol
-mintel-asm  -mno-clean-linkage  -mno-code-align @gol
-mno-complex-addr  -mno-leaf-procedures @gol
-mno-old-align  -mno-strict-align  -mno-tail-call @gol
-mnumerics  -mold-align  -msoft-float  -mstrict-align @gol
-mtail-call}

@emph{DEC Alpha Options}
@gccoptlist{-mno-fp-regs  -msoft-float  -malpha-as  -mgas @gol
-mieee  -mieee-with-inexact  -mieee-conformant @gol
-mfp-trap-mode=@var{mode}  -mfp-rounding-mode=@var{mode} @gol
-mtrap-precision=@var{mode}  -mbuild-constants @gol
-mcpu=@var{cpu-type}  -mtune=@var{cpu-type} @gol
-mbwx  -mmax  -mfix  -mcix @gol
-mfloat-vax  -mfloat-ieee @gol
-mexplicit-relocs  -msmall-data  -mlarge-data @gol
-msmall-text  -mlarge-text @gol
-mmemory-latency=@var{time}}

@emph{DEC Alpha/VMS Options}
@gccoptlist{-mvms-return-codes}

@emph{H8/300 Options}
@gccoptlist{-mrelax  -mh  -ms  -mn  -mint32  -malign-300}

@emph{SH Options}
@gccoptlist{-m1  -m2  -m2e  -m3  -m3e @gol
-m4-nofpu  -m4-single-only  -m4-single  -m4 @gol
-m5-64media  -m5-64media-nofpu @gol
-m5-32media  -m5-32media-nofpu @gol
-m5-compact  -m5-compact-nofpu @gol
-mb  -ml  -mdalign  -mrelax @gol
-mbigtable  -mfmovd  -mhitachi  -mnomacsave @gol
-mieee  -misize  -mpadstruct  -mspace @gol
-mprefergot  -musermode}

@emph{System V Options}
@gccoptlist{-Qy  -Qn  -YP,@var{paths}  -Ym,@var{dir}}

@emph{ARC Options}
@gccoptlist{-EB  -EL @gol
-mmangle-cpu  -mcpu=@var{cpu}  -mtext=@var{text-section} @gol
-mdata=@var{data-section}  -mrodata=@var{readonly-data-section}}

@emph{TMS320C3x/C4x Options}
@gccoptlist{-mcpu=@var{cpu}  -mbig  -msmall  -mregparm  -mmemparm @gol
-mfast-fix  -mmpyi  -mbk  -mti  -mdp-isr-reload @gol
-mrpts=@var{count}  -mrptb  -mdb  -mloop-unsigned @gol
-mparallel-insns  -mparallel-mpy  -mpreserve-float}

@emph{V850 Options}
@gccoptlist{-mlong-calls  -mno-long-calls  -mep  -mno-ep @gol
-mprolog-function  -mno-prolog-function  -mspace @gol
-mtda=@var{n}  -msda=@var{n}  -mzda=@var{n} @gol
-mapp-regs  -mno-app-regs @gol
-mdisable-callt  -mno-disable-callt @gol
-mv850e @gol
-mv850  -mbig-switch}

@emph{NS32K Options}
@gccoptlist{-m32032  -m32332  -m32532  -m32081  -m32381 @gol
-mmult-add  -mnomult-add  -msoft-float  -mrtd  -mnortd @gol
-mregparam  -mnoregparam  -msb  -mnosb @gol
-mbitfield  -mnobitfield  -mhimem  -mnohimem}

@emph{AVR Options}
@gccoptlist{-mmcu=@var{mcu}  -msize  -minit-stack=@var{n}  -mno-interrupts @gol
-mcall-prologues  -mno-tablejump  -mtiny-stack}

@emph{MCore Options}
@gccoptlist{-mhardlit  -mno-hardlit  -mdiv  -mno-div  -mrelax-immediates @gol
-mno-relax-immediates  -mwide-bitfields  -mno-wide-bitfields @gol
-m4byte-functions  -mno-4byte-functions  -mcallgraph-data @gol
-mno-callgraph-data  -mslow-bytes  -mno-slow-bytes  -mno-lsim @gol
-mlittle-endian  -mbig-endian  -m210  -m340  -mstack-increment}

@emph{MMIX Options}
@gccoptlist{-mlibfuncs  -mno-libfuncs  -mepsilon  -mno-epsilon  -mabi=gnu @gol
-mabi=mmixware  -mzero-extend  -mknuthdiv  -mtoplevel-symbols @gol
-melf  -mbranch-predict  -mno-branch-predict  -mbase-addresses @gol
-mno-base-addresses  -msingle-exit  -mno-single-exit}

@emph{IA-64 Options}
@gccoptlist{-mbig-endian  -mlittle-endian  -mgnu-as  -mgnu-ld  -mno-pic @gol
-mvolatile-asm-stop  -mb-step  -mregister-names  -mno-sdata @gol
-mconstant-gp  -mauto-pic  -minline-float-divide-min-latency @gol
-minline-float-divide-max-throughput @gol
-minline-int-divide-min-latency @gol
-minline-int-divide-max-throughput  -mno-dwarf2-asm @gol
-mfixed-range=@var{register-range}}

@emph{D30V Options}
@gccoptlist{-mextmem  -mextmemory  -monchip  -mno-asm-optimize @gol
-masm-optimize  -mbranch-cost=@var{n}  -mcond-exec=@var{n}}

@emph{S/390 and zSeries Options}
@gccoptlist{-mtune=@var{cpu-type}  -march=@var{cpu-type} @gol
-mhard-float  -msoft-float  -mbackchain  -mno-backchain @gol
-msmall-exec  -mno-small-exec  -mmvcle -mno-mvcle @gol
-m64  -m31  -mdebug  -mno-debug  -mesa  -mzarch}

@emph{CRIS Options}
@gccoptlist{-mcpu=@var{cpu}  -march=@var{cpu}  -mtune=@var{cpu} @gol
-mmax-stack-frame=@var{n}  -melinux-stacksize=@var{n} @gol
-metrax4  -metrax100  -mpdebug  -mcc-init  -mno-side-effects @gol
-mstack-align  -mdata-align  -mconst-align @gol
-m32-bit  -m16-bit  -m8-bit  -mno-prologue-epilogue  -mno-gotplt @gol
-melf  -maout  -melinux  -mlinux  -sim  -sim2}

@emph{PDP-11 Options}
@gccoptlist{-mfpu  -msoft-float  -mac0  -mno-ac0  -m40  -m45  -m10 @gol
-mbcopy  -mbcopy-builtin  -mint32  -mno-int16 @gol
-mint16  -mno-int32  -mfloat32  -mno-float64 @gol
-mfloat64  -mno-float32  -mabshi  -mno-abshi @gol
-mbranch-expensive  -mbranch-cheap @gol
-msplit  -mno-split  -munix-asm  -mdec-asm}

@emph{Xstormy16 Options}
@gccoptlist{-msim}

@emph{Xtensa Options}
@gccoptlist{-mbig-endian  -mlittle-endian @gol
-mdensity  -mno-density @gol
-mconst16 -mno-const16 @gol
-mabs -mno-abs @gol
-maddx -mno-addx @gol
-mmac16  -mno-mac16 @gol
-mmul16  -mno-mul16 @gol
-mmul32  -mno-mul32 @gol
-mnsa  -mno-nsa @gol
-mminmax  -mno-minmax @gol
-msext  -mno-sext @gol
-mbooleans  -mno-booleans @gol
-mhard-float  -msoft-float @gol
-mfused-madd  -mno-fused-madd @gol
-mtext-section-literals  -mno-text-section-literals @gol
-mtarget-align  -mno-target-align @gol
-mlongcalls  -mno-longcalls}

@emph{FRV Options}
@gccoptlist{-mgpr-32  -mgpr-64  -mfpr-32  -mfpr-64 @gol
-mhard-float  -msoft-float @gol
-malloc-cc  -mfixed-cc  -mdword  -mno-dword @gol
-mdouble  -mno-double @gol
-mmedia  -mno-media  -mmuladd  -mno-muladd @gol
-mlibrary-pic  -macc-4 -macc-8 @gol
-mpack  -mno-pack  -mno-eflags  -mcond-move  -mno-cond-move @gol
-mscc  -mno-scc  -mcond-exec  -mno-cond-exec @gol
-mvliw-branch  -mno-vliw-branch @gol
-mmulti-cond-exec  -mno-multi-cond-exec  -mnested-cond-exec @gol
-mno-nested-cond-exec  -mtomcat-stats @gol
-mcpu=@var{cpu}}

@item Code Generation Options
@xref{Code Gen Options,,Options for Code Generation Conventions}.
@gccoptlist{-fcall-saved-@var{reg}  -fcall-used-@var{reg} @gol
-ffixed-@var{reg}  -fexceptions @gol
-fnon-call-exceptions  -funwind-tables @gol
-fasynchronous-unwind-tables @gol
-finhibit-size-directive  -finstrument-functions @gol
-fno-common  -fno-ident  -fno-gnu-linker @gol
-fpcc-struct-return  -fpic  -fPIC @gol
-freg-struct-return  -fshared-data  -fshort-enums @gol
-fshort-double  -fshort-wchar @gol
-fverbose-asm  -fpack-struct  -fstack-check @gol
-fstack-limit-register=@var{reg}  -fstack-limit-symbol=@var{sym} @gol
-fargument-alias  -fargument-noalias @gol
-fargument-noalias-global  -fleading-underscore @gol
-ftls-model=@var{model} @gol
-ftrapv  -fbounds-check}
@end table

@menu
* Overall Options::     Controlling the kind of output:
                        an executable, object files, assembler files,
                        or preprocessed source.
* C Dialect Options::   Controlling the variant of C language compiled.
* C++ Dialect Options:: Variations on C++.
* Objective-C Dialect Options:: Variations on Objective-C.
* Language Independent Options:: Controlling how diagnostics should be
                        formatted.
* Warning Options::     How picky should the compiler be?
* Debugging Options::   Symbol tables, measurements, and debugging dumps.
* Optimize Options::    How much optimization?
* Preprocessor Options:: Controlling header files and macro definitions.
                         Also, getting dependency information for Make.
* Assembler Options::   Passing options to the assembler.
* Link Options::        Specifying libraries and so on.
* Directory Options::   Where to find header files and libraries.
                        Where to find the compiler executable files.
* Spec Files::          How to pass switches to sub-processes.
* Target Options::      Running a cross-compiler, or an old version of GCC.
@end menu

@node Overall Options
@section Options Controlling the Kind of Output

Compilation can involve up to four stages: preprocessing, compilation
proper, assembly and linking, always in that order.  The first three
stages apply to an individual source file, and end by producing an
object file; linking combines all the object files (those newly
compiled, and those specified as input) into an executable file.

@cindex file name suffix
For any given input file, the file name suffix determines what kind of
compilation is done:

@table @gcctabopt
@item @var{file}.c
C source code which must be preprocessed.

@item @var{file}.i
C source code which should not be preprocessed.

@item @var{file}.ii
C++ source code which should not be preprocessed.

@item @var{file}.m
Objective-C source code.  Note that you must link with the library
@file{libobjc.a} to make an Objective-C program work.

@item @var{file}.mi
Objective-C source code which should not be preprocessed.

@item @var{file}.h
C or C++ header file to be turned into a precompiled header.

@item @var{file}.cc
@itemx @var{file}.cp
@itemx @var{file}.cxx
@itemx @var{file}.cpp
@itemx @var{file}.CPP
@itemx @var{file}.c++
@itemx @var{file}.C
C++ source code which must be preprocessed.  Note that in @samp{.cxx},
the last two letters must both be literally @samp{x}.  Likewise,
@samp{.C} refers to a literal capital C@.

@item @var{file}.hh
@itemx @var{file}.H
C++ header file to be turned into a precompiled header.

@item @var{file}.f
@itemx @var{file}.for
@itemx @var{file}.FOR
Fortran source code which should not be preprocessed.

@item @var{file}.F
@itemx @var{file}.fpp
@itemx @var{file}.FPP
Fortran source code which must be preprocessed (with the traditional
preprocessor).

@item @var{file}.r
Fortran source code which must be preprocessed with a RATFOR
preprocessor (not included with GCC)@.

@xref{Overall Options,,Options Controlling the Kind of Output, g77,
Using and Porting GNU Fortran}, for more details of the handling of
Fortran input files.

@c FIXME: Descriptions of Java file types.
@c @var{file}.java
@c @var{file}.class
@c @var{file}.zip
@c @var{file}.jar

@item @var{file}.ads
Ada source code file which contains a library unit declaration (a
declaration of a package, subprogram, or generic, or a generic
instantiation), or a library unit renaming declaration (a package,
generic, or subprogram renaming declaration).  Such files are also
called @dfn{specs}.

@itemx @var{file}.adb
Ada source code file containing a library unit body (a subprogram or
package body).  Such files are also called @dfn{bodies}.

@c GCC also knows about some suffixes for languages not yet included:
@c Pascal:
@c @var{file}.p
@c @var{file}.pas

@item @var{file}.s
Assembler code.

@item @var{file}.S
Assembler code which must be preprocessed.

@item @var{other}
An object file to be fed straight into linking.
Any file name with no recognized suffix is treated this way.
@end table

@opindex x
You can specify the input language explicitly with the @option{-x} option:

@table @gcctabopt
@item -x @var{language}
Specify explicitly the @var{language} for the following input files
(rather than letting the compiler choose a default based on the file
name suffix).  This option applies to all following input files until
the next @option{-x} option.  Possible values for @var{language} are:
@example
c  c-header  cpp-output
c++  c++-header  c++-cpp-output
objective-c  objective-c-header  objc-cpp-output
assembler  assembler-with-cpp
ada
f77  f77-cpp-input  ratfor
java
treelang
@end example

@item -x none
Turn off any specification of a language, so that subsequent files are
handled according to their file name suffixes (as they are if @option{-x}
has not been used at all).

@item -pass-exit-codes
@opindex pass-exit-codes
Normally the @command{gcc} program will exit with the code of 1 if any
phase of the compiler returns a non-success return code.  If you specify
@option{-pass-exit-codes}, the @command{gcc} program will instead return with
numerically highest error produced by any phase that returned an error
indication.
@end table

If you only want some of the stages of compilation, you can use
@option{-x} (or filename suffixes) to tell @command{gcc} where to start, and
one of the options @option{-c}, @option{-S}, or @option{-E} to say where
@command{gcc} is to stop.  Note that some combinations (for example,
@samp{-x cpp-output -E}) instruct @command{gcc} to do nothing at all.

@table @gcctabopt
@item -c
@opindex c
Compile or assemble the source files, but do not link.  The linking
stage simply is not done.  The ultimate output is in the form of an
object file for each source file.

By default, the object file name for a source file is made by replacing
the suffix @samp{.c}, @samp{.i}, @samp{.s}, etc., with @samp{.o}.

Unrecognized input files, not requiring compilation or assembly, are
ignored.

@item -S
@opindex S
Stop after the stage of compilation proper; do not assemble.  The output
is in the form of an assembler code file for each non-assembler input
file specified.

By default, the assembler file name for a source file is made by
replacing the suffix @samp{.c}, @samp{.i}, etc., with @samp{.s}.

Input files that don't require compilation are ignored.

@item -E
@opindex E
Stop after the preprocessing stage; do not run the compiler proper.  The
output is in the form of preprocessed source code, which is sent to the
standard output.

Input files which don't require preprocessing are ignored.

@cindex output file option
@item -o @var{file}
@opindex o
Place output in file @var{file}.  This applies regardless to whatever
sort of output is being produced, whether it be an executable file,
an object file, an assembler file or preprocessed C code.

Since only one output file can be specified, it does not make sense to
use @option{-o} when compiling more than one input file, unless you are
producing an executable file as output.

If @option{-o} is not specified, the default is to put an executable file
in @file{a.out}, the object file for @file{@var{source}.@var{suffix}} in
@file{@var{source}.o}, its assembler file in @file{@var{source}.s}, and
all preprocessed C source on standard output.

@item -v
@opindex v
Print (on standard error output) the commands executed to run the stages
of compilation.  Also print the version number of the compiler driver
program and of the preprocessor and the compiler proper.

@item -###
@opindex ###
Like @option{-v} except the commands are not executed and all command
arguments are quoted.  This is useful for shell scripts to capture the
driver-generated command lines.

@item -pipe
@opindex pipe
Use pipes rather than temporary files for communication between the
various stages of compilation.  This fails to work on some systems where
the assembler is unable to read from a pipe; but the GNU assembler has
no trouble.

@item --help
@opindex help
Print (on the standard output) a description of the command line options
understood by @command{gcc}.  If the @option{-v} option is also specified
then @option{--help} will also be passed on to the various processes
invoked by @command{gcc}, so that they can display the command line options
they accept.  If the @option{-Wextra} option is also specified then command
line options which have no documentation associated with them will also
be displayed.

@item --target-help
@opindex target-help
Print (on the standard output) a description of target specific command
line options for each tool.

@item --version
@opindex version
Display the version number and copyrights of the invoked GCC.
@end table

@node Invoking G++
@section Compiling C++ Programs

@cindex suffixes for C++ source
@cindex C++ source file suffixes
C++ source files conventionally use one of the suffixes @samp{.C},
@samp{.cc}, @samp{.cpp}, @samp{.CPP}, @samp{.c++}, @samp{.cp}, or
@samp{.cxx}; C++ header files often use @samp{.hh} or @samp{.H}; and
preprocessed C++ files use the suffix @samp{.ii}.  GCC recognizes
files with these names and compiles them as C++ programs even if you
call the compiler the same way as for compiling C programs (usually
with the name @command{gcc}).

@findex g++
@findex c++
However, C++ programs often require class libraries as well as a
compiler that understands the C++ language---and under some
circumstances, you might want to compile programs or header files from
standard input, or otherwise without a suffix that flags them as C++
programs.  You might also like to precompile a C header file with a
@samp{.h} extension to be used in C++ compilations.  @command{g++} is a
program that calls GCC with the default language set to C++, and
automatically specifies linking against the C++ library.  On many
systems, @command{g++} is also installed with the name @command{c++}.

@cindex invoking @command{g++}
When you compile C++ programs, you may specify many of the same
command-line options that you use for compiling programs in any
language; or command-line options meaningful for C and related
languages; or options that are meaningful only for C++ programs.
@xref{C Dialect Options,,Options Controlling C Dialect}, for
explanations of options for languages related to C@.
@xref{C++ Dialect Options,,Options Controlling C++ Dialect}, for
explanations of options that are meaningful only for C++ programs.

@node C Dialect Options
@section Options Controlling C Dialect
@cindex dialect options
@cindex language dialect options
@cindex options, dialect

The following options control the dialect of C (or languages derived
from C, such as C++ and Objective-C) that the compiler accepts:

@table @gcctabopt
@cindex ANSI support
@cindex ISO support
@item -ansi
@opindex ansi
In C mode, support all ISO C90 programs.  In C++ mode,
remove GNU extensions that conflict with ISO C++.

This turns off certain features of GCC that are incompatible with ISO
C90 (when compiling C code), or of standard C++ (when compiling C++ code),
such as the @code{asm} and @code{typeof} keywords, and
predefined macros such as @code{unix} and @code{vax} that identify the
type of system you are using.  It also enables the undesirable and
rarely used ISO trigraph feature.  For the C compiler,
it disables recognition of C++ style @samp{//} comments as well as
the @code{inline} keyword.

The alternate keywords @code{__asm__}, @code{__extension__},
@code{__inline__} and @code{__typeof__} continue to work despite
@option{-ansi}.  You would not want to use them in an ISO C program, of
course, but it is useful to put them in header files that might be included
in compilations done with @option{-ansi}.  Alternate predefined macros
such as @code{__unix__} and @code{__vax__} are also available, with or
without @option{-ansi}.

The @option{-ansi} option does not cause non-ISO programs to be
rejected gratuitously.  For that, @option{-pedantic} is required in
addition to @option{-ansi}.  @xref{Warning Options}.

The macro @code{__STRICT_ANSI__} is predefined when the @option{-ansi}
option is used.  Some header files may notice this macro and refrain
from declaring certain functions or defining certain macros that the
ISO standard doesn't call for; this is to avoid interfering with any
programs that might use these names for other things.

Functions which would normally be built in but do not have semantics
defined by ISO C (such as @code{alloca} and @code{ffs}) are not built-in
functions with @option{-ansi} is used.  @xref{Other Builtins,,Other
built-in functions provided by GCC}, for details of the functions
affected.

@item -std=
@opindex std
Determine the language standard.  This option is currently only
supported when compiling C or C++.  A value for this option must be
provided; possible values are

@table @samp
@item c89
@itemx iso9899:1990
ISO C90 (same as @option{-ansi}).

@item iso9899:199409
ISO C90 as modified in amendment 1.

@item c99
@itemx c9x
@itemx iso9899:1999
@itemx iso9899:199x
ISO C99.  Note that this standard is not yet fully supported; see
@w{@uref{http://gcc.gnu.org/c99status.html}} for more information.  The
names @samp{c9x} and @samp{iso9899:199x} are deprecated.

@item gnu89
Default, ISO C90 plus GNU extensions (including some C99 features).

@item gnu99
@item gnu9x
ISO C99 plus GNU extensions.  When ISO C99 is fully implemented in GCC,
this will become the default.  The name @samp{gnu9x} is deprecated.

@item c++98
The 1998 ISO C++ standard plus amendments.

@item gnu++98
The same as @option{-std=c++98} plus GNU extensions.  This is the
default for C++ code.
@end table

Even when this option is not specified, you can still use some of the
features of newer standards in so far as they do not conflict with
previous C standards.  For example, you may use @code{__restrict__} even
when @option{-std=c99} is not specified.

The @option{-std} options specifying some version of ISO C have the same
effects as @option{-ansi}, except that features that were not in ISO C90
but are in the specified version (for example, @samp{//} comments and
the @code{inline} keyword in ISO C99) are not disabled.

@xref{Standards,,Language Standards Supported by GCC}, for details of
these standard versions.

@item -aux-info @var{filename}
@opindex aux-info
Output to the given filename prototyped declarations for all functions
declared and/or defined in a translation unit, including those in header
files.  This option is silently ignored in any language other than C@.

Besides declarations, the file indicates, in comments, the origin of
each declaration (source file and line), whether the declaration was
implicit, prototyped or unprototyped (@samp{I}, @samp{N} for new or
@samp{O} for old, respectively, in the first character after the line
number and the colon), and whether it came from a declaration or a
definition (@samp{C} or @samp{F}, respectively, in the following
character).  In the case of function definitions, a K&R-style list of
arguments followed by their declarations is also provided, inside
comments, after the declaration.

@item -fno-asm
@opindex fno-asm
Do not recognize @code{asm}, @code{inline} or @code{typeof} as a
keyword, so that code can use these words as identifiers.  You can use
the keywords @code{__asm__}, @code{__inline__} and @code{__typeof__}
instead.  @option{-ansi} implies @option{-fno-asm}.

In C++, this switch only affects the @code{typeof} keyword, since
@code{asm} and @code{inline} are standard keywords.  You may want to
use the @option{-fno-gnu-keywords} flag instead, which has the same
effect.  In C99 mode (@option{-std=c99} or @option{-std=gnu99}), this
switch only affects the @code{asm} and @code{typeof} keywords, since
@code{inline} is a standard keyword in ISO C99.

@item -fno-builtin
@itemx -fno-builtin-@var{function}
@opindex fno-builtin
@cindex built-in functions
Don't recognize built-in functions that do not begin with
@samp{__builtin_} as prefix.  @xref{Other Builtins,,Other built-in
functions provided by GCC}, for details of the functions affected,
including those which are not built-in functions when @option{-ansi} or
@option{-std} options for strict ISO C conformance are used because they
do not have an ISO standard meaning.

GCC normally generates special code to handle certain built-in functions
more efficiently; for instance, calls to @code{alloca} may become single
instructions that adjust the stack directly, and calls to @code{memcpy}
may become inline copy loops.  The resulting code is often both smaller
and faster, but since the function calls no longer appear as such, you
cannot set a breakpoint on those calls, nor can you change the behavior
of the functions by linking with a different library.

With the @option{-fno-builtin-@var{function}} option
only the built-in function @var{function} is
disabled.  @var{function} must not begin with @samp{__builtin_}.  If a
function is named this is not built-in in this version of GCC, this
option is ignored.  There is no corresponding
@option{-fbuiltin-@var{function}} option; if you wish to enable
built-in functions selectively when using @option{-fno-builtin} or
@option{-ffreestanding}, you may define macros such as:

@smallexample
#define abs(n)          __builtin_abs ((n))
#define strcpy(d, s)    __builtin_strcpy ((d), (s))
@end smallexample

@item -fhosted
@opindex fhosted
@cindex hosted environment

Assert that compilation takes place in a hosted environment.  This implies
@option{-fbuiltin}.  A hosted environment is one in which the
entire standard library is available, and in which @code{main} has a return
type of @code{int}.  Examples are nearly everything except a kernel.
This is equivalent to @option{-fno-freestanding}.

@item -ffreestanding
@opindex ffreestanding
@cindex hosted environment

Assert that compilation takes place in a freestanding environment.  This
implies @option{-fno-builtin}.  A freestanding environment
is one in which the standard library may not exist, and program startup may
not necessarily be at @code{main}.  The most obvious example is an OS kernel.
This is equivalent to @option{-fno-hosted}.

@xref{Standards,,Language Standards Supported by GCC}, for details of
freestanding and hosted environments.

@item -fms-extensions
@opindex fms-extensions
Accept some non-standard constructs used in Microsoft header files.

@item -trigraphs
@opindex trigraphs
Support ISO C trigraphs.  The @option{-ansi} option (and @option{-std}
options for strict ISO C conformance) implies @option{-trigraphs}.

@item -no-integrated-cpp
@opindex no-integrated-cpp
Performs a compilation in two passes: preprocessing and compiling.  This
option allows a user supplied "cc1", "cc1plus", or "cc1obj" via the
@option{-B} option. The user supplied compilation step can then add in
an additional preprocessing step after normal preprocessing but before
compiling. The default is to use the integrated cpp (internal cpp)

The semantics of this option will change if "cc1", "cc1plus", and
"cc1obj" are merged.

@cindex traditional C language
@cindex C language, traditional
@item -traditional
@itemx -traditional-cpp
@opindex traditional-cpp
@opindex traditional
Formerly, these options caused GCC to attempt to emulate a pre-standard
C compiler.  They are now only supported with the @option{-E} switch.
The preprocessor continues to support a pre-standard mode.  See the GNU
CPP manual for details.

@item -fcond-mismatch
@opindex fcond-mismatch
Allow conditional expressions with mismatched types in the second and
third arguments.  The value of such an expression is void.  This option
is not supported for C++.

@item -funsigned-char
@opindex funsigned-char
Let the type @code{char} be unsigned, like @code{unsigned char}.

Each kind of machine has a default for what @code{char} should
be.  It is either like @code{unsigned char} by default or like
@code{signed char} by default.

Ideally, a portable program should always use @code{signed char} or
@code{unsigned char} when it depends on the signedness of an object.
But many programs have been written to use plain @code{char} and
expect it to be signed, or expect it to be unsigned, depending on the
machines they were written for.  This option, and its inverse, let you
make such a program work with the opposite default.

The type @code{char} is always a distinct type from each of
@code{signed char} or @code{unsigned char}, even though its behavior
is always just like one of those two.

@item -fsigned-char
@opindex fsigned-char
Let the type @code{char} be signed, like @code{signed char}.

Note that this is equivalent to @option{-fno-unsigned-char}, which is
the negative form of @option{-funsigned-char}.  Likewise, the option
@option{-fno-signed-char} is equivalent to @option{-funsigned-char}.

@item -fsigned-bitfields
@itemx -funsigned-bitfields
@itemx -fno-signed-bitfields
@itemx -fno-unsigned-bitfields
@opindex fsigned-bitfields
@opindex funsigned-bitfields
@opindex fno-signed-bitfields
@opindex fno-unsigned-bitfields
These options control whether a bit-field is signed or unsigned, when the
declaration does not use either @code{signed} or @code{unsigned}.  By
default, such a bit-field is signed, because this is consistent: the
basic integer types such as @code{int} are signed types.

@item -fwritable-strings
@opindex fwritable-strings
Store string constants in the writable data segment and don't uniquize
them.  This is for compatibility with old programs which assume they can
write into string constants.

Writing into string constants is a very bad idea; ``constants'' should
be constant.
@end table

@node C++ Dialect Options
@section Options Controlling C++ Dialect

@cindex compiler options, C++
@cindex C++ options, command line
@cindex options, C++
This section describes the command-line options that are only meaningful
for C++ programs; but you can also use most of the GNU compiler options
regardless of what language your program is in.  For example, you
might compile a file @code{firstClass.C} like this:

@example
g++ -g -frepo -O -c firstClass.C
@end example

@noindent
In this example, only @option{-frepo} is an option meant
only for C++ programs; you can use the other options with any
language supported by GCC@.

Here is a list of options that are @emph{only} for compiling C++ programs:

@table @gcctabopt

@item -fabi-version=@var{n}
@opindex fabi-version
Use version @var{n} of the C++ ABI.  Version 1 is the version of the C++
ABI that first appeared in G++ 3.2.  Version 0 will always be the
version that conforms most closely to the C++ ABI specification.
Therefore, the ABI obtained using version 0 will change as ABI bugs are
fixed.

The default is version 1.

@item -fno-access-control
@opindex fno-access-control
Turn off all access checking.  This switch is mainly useful for working
around bugs in the access control code.

@item -fcheck-new
@opindex fcheck-new
Check that the pointer returned by @code{operator new} is non-null
before attempting to modify the storage allocated.  This check is
normally unnecessary because the C++ standard specifies that
@code{operator new} will only return @code{0} if it is declared
@samp{throw()}, in which case the compiler will always check the
return value even without this option.  In all other cases, when
@code{operator new} has a non-empty exception specification, memory
exhaustion is signalled by throwing @code{std::bad_alloc}.  See also
@samp{new (nothrow)}.

@item -fconserve-space
@opindex fconserve-space
Put uninitialized or runtime-initialized global variables into the
common segment, as C does.  This saves space in the executable at the
cost of not diagnosing duplicate definitions.  If you compile with this
flag and your program mysteriously crashes after @code{main()} has
completed, you may have an object that is being destroyed twice because
two definitions were merged.

This option is no longer useful on most targets, now that support has
been added for putting variables into BSS without making them common.

@item -fno-const-strings
@opindex fno-const-strings
Give string constants type @code{char *} instead of type @code{const
char *}.  By default, G++ uses type @code{const char *} as required by
the standard.  Even if you use @option{-fno-const-strings}, you cannot
actually modify the value of a string constant, unless you also use
@option{-fwritable-strings}.

This option might be removed in a future release of G++.  For maximum
portability, you should structure your code so that it works with
string constants that have type @code{const char *}.

@item -fno-elide-constructors
@opindex fno-elide-constructors
The C++ standard allows an implementation to omit creating a temporary
which is only used to initialize another object of the same type.
Specifying this option disables that optimization, and forces G++ to
call the copy constructor in all cases.

@item -fno-enforce-eh-specs
@opindex fno-enforce-eh-specs
Don't check for violation of exception specifications at runtime.  This
option violates the C++ standard, but may be useful for reducing code
size in production builds, much like defining @samp{NDEBUG}.  The compiler
will still optimize based on the exception specifications.

@item -fexternal-templates
@opindex fexternal-templates

Cause @samp{#pragma interface} and @samp{implementation} to apply to
template instantiation; template instances are emitted or not according
to the location of the template definition.  @xref{Template
Instantiation}, for more information.

This option is deprecated.

@item -falt-external-templates
@opindex falt-external-templates
Similar to @option{-fexternal-templates}, but template instances are
emitted or not according to the place where they are first instantiated.
@xref{Template Instantiation}, for more information.

This option is deprecated.

@item -ffor-scope
@itemx -fno-for-scope
@opindex ffor-scope
@opindex fno-for-scope
If @option{-ffor-scope} is specified, the scope of variables declared in
a @i{for-init-statement} is limited to the @samp{for} loop itself,
as specified by the C++ standard.
If @option{-fno-for-scope} is specified, the scope of variables declared in
a @i{for-init-statement} extends to the end of the enclosing scope,
as was the case in old versions of G++, and other (traditional)
implementations of C++.

The default if neither flag is given to follow the standard,
but to allow and give a warning for old-style code that would
otherwise be invalid, or have different behavior.

@item -fno-gnu-keywords
@opindex fno-gnu-keywords
Do not recognize @code{typeof} as a keyword, so that code can use this
word as an identifier.  You can use the keyword @code{__typeof__} instead.
@option{-ansi} implies @option{-fno-gnu-keywords}.

@item -fno-implicit-templates
@opindex fno-implicit-templates
Never emit code for non-inline templates which are instantiated
implicitly (i.e.@: by use); only emit code for explicit instantiations.
@xref{Template Instantiation}, for more information.

@item -fno-implicit-inline-templates
@opindex fno-implicit-inline-templates
Don't emit code for implicit instantiations of inline templates, either.
The default is to handle inlines differently so that compiles with and
without optimization will need the same set of explicit instantiations.

@item -fno-implement-inlines
@opindex fno-implement-inlines
To save space, do not emit out-of-line copies of inline functions
controlled by @samp{#pragma implementation}.  This will cause linker
errors if these functions are not inlined everywhere they are called.

@item -fms-extensions
@opindex fms-extensions
Disable pedantic warnings about constructs used in MFC, such as implicit
int and getting a pointer to member function via non-standard syntax.

@item -fno-nonansi-builtins
@opindex fno-nonansi-builtins
Disable built-in declarations of functions that are not mandated by
ANSI/ISO C@.  These include @code{ffs}, @code{alloca}, @code{_exit},
@code{index}, @code{bzero}, @code{conjf}, and other related functions.

@item -fno-operator-names
@opindex fno-operator-names
Do not treat the operator name keywords @code{and}, @code{bitand},
@code{bitor}, @code{compl}, @code{not}, @code{or} and @code{xor} as
synonyms as keywords.

@item -fno-optional-diags
@opindex fno-optional-diags
Disable diagnostics that the standard says a compiler does not need to
issue.  Currently, the only such diagnostic issued by G++ is the one for
a name having multiple meanings within a class.

@item -fpermissive
@opindex fpermissive
Downgrade messages about nonconformant code from errors to warnings.  By
default, G++ effectively sets @option{-pedantic-errors} without
@option{-pedantic}; this option reverses that.  This behavior and this
option are superseded by @option{-pedantic}, which works as it does for GNU C@.

@item -frepo
@opindex frepo
Enable automatic template instantiation at link time.  This option also
implies @option{-fno-implicit-templates}.  @xref{Template
Instantiation}, for more information.

@item -fno-rtti
@opindex fno-rtti
Disable generation of information about every class with virtual
functions for use by the C++ runtime type identification features
(@samp{dynamic_cast} and @samp{typeid}).  If you don't use those parts
of the language, you can save some space by using this flag.  Note that
exception handling uses the same information, but it will generate it as
needed.

@item -fstats
@opindex fstats
Emit statistics about front-end processing at the end of the compilation.
This information is generally only useful to the G++ development team.

@item -ftemplate-depth-@var{n}
@opindex ftemplate-depth
Set the maximum instantiation depth for template classes to @var{n}.
A limit on the template instantiation depth is needed to detect
endless recursions during template class instantiation.  ANSI/ISO C++
conforming programs must not rely on a maximum depth greater than 17.

@item -fuse-cxa-atexit
@opindex fuse-cxa-atexit
Register destructors for objects with static storage duration with the
@code{__cxa_atexit} function rather than the @code{atexit} function.
This option is required for fully standards-compliant handling of static
destructors, but will only work if your C library supports
@code{__cxa_atexit}.

@item -fvtable-gc
@opindex fvtable-gc
Emit special relocations for vtables and virtual function references
so that the linker can identify unused virtual functions and zero out
vtable slots that refer to them.  This is most useful with
@option{-ffunction-sections} and @option{-Wl,--gc-sections}, in order to
also discard the functions themselves.

This optimization requires GNU as and GNU ld.  Not all systems support
this option.  @option{-Wl,--gc-sections} is ignored without @option{-static}.

@item -fno-weak
@opindex fno-weak
Do not use weak symbol support, even if it is provided by the linker.
By default, G++ will use weak symbols if they are available.  This
option exists only for testing, and should not be used by end-users;
it will result in inferior code and has no benefits.  This option may
be removed in a future release of G++.

@item -nostdinc++
@opindex nostdinc++
Do not search for header files in the standard directories specific to
C++, but do still search the other standard directories.  (This option
is used when building the C++ library.)
@end table

In addition, these optimization, warning, and code generation options
have meanings only for C++ programs:

@table @gcctabopt
@item -fno-default-inline
@opindex fno-default-inline
Do not assume @samp{inline} for functions defined inside a class scope.
@xref{Optimize Options,,Options That Control Optimization}.  Note that these
functions will have linkage like inline functions; they just won't be
inlined by default.

@item -Wabi @r{(C++ only)}
@opindex Wabi
Warn when G++ generates code that is probably not compatible with the
vendor-neutral C++ ABI.  Although an effort has been made to warn about
all such cases, there are probably some cases that are not warned about, 
even though G++ is generating incompatible code.  There may also be
cases where warnings are emitted even though the code that is generated
will be compatible.

You should rewrite your code to avoid these warnings if you are
concerned about the fact that code generated by G++ may not be binary
compatible with code generated by other compilers.

The known incompatibilities at this point include:

@itemize @bullet

@item
Incorrect handling of tail-padding for bit-fields.  G++ may attempt to
pack data into the same byte as a base class.  For example:

@smallexample
struct A @{ virtual void f(); int f1 : 1; @};
struct B : public A @{ int f2 : 1; @};
@end smallexample

@noindent
In this case, G++ will place @code{B::f2} into the same byte
as@code{A::f1}; other compilers will not.  You can avoid this problem 
by explicitly padding @code{A} so that its size is a multiple of the
byte size on your platform; that will cause G++ and other compilers to
layout @code{B} identically.

@item
Incorrect handling of tail-padding for virtual bases.  G++ does not use
tail padding when laying out virtual bases.  For example:

@smallexample
struct A @{ virtual void f(); char c1; @};
struct B @{ B(); char c2; @};
struct C : public A, public virtual B @{@};
@end smallexample

@noindent
In this case, G++ will not place @code{B} into the tail-padding for
@code{A}; other compilers will.  You can avoid this problem by
explicitly padding @code{A} so that its size is a multiple of its
alignment (ignoring virtual base classes); that will cause G++ and other
compilers to layout @code{C} identically.

@item
Incorrect handling of bit-fields with declared widths greater than that
of their underlying types, when the bit-fields appear in a union.  For
example:

@smallexample
union U @{ int i : 4096; @};
@end smallexample

@noindent
Assuming that an @code{int} does not have 4096 bits, G++ will make the
union too small by the number of bits in an @code{int}.

@item
Empty classes can be placed at incorrect offsets.  For example:
 
@smallexample
struct A @{@};

struct B @{
  A a;
  virtual void f ();
@};

struct C : public B, public A @{@};
@end smallexample

@noindent
G++ will place the @code{A} base class of @code{C} at a nonzero offset;
it should be placed at offset zero.  G++ mistakenly believes that the
@code{A} data member of @code{B} is already at offset zero.

@item
Names of template functions whose types involve @code{typename} or
template template parameters can be mangled incorrectly.

@smallexample
template <typename Q>
void f(typename Q::X) @{@}

template <template <typename> class Q>
void f(typename Q<int>::X) @{@}
@end smallexample

@noindent
Instantiations of these templates may be mangled incorrectly.

@end itemize

@item -Wctor-dtor-privacy @r{(C++ only)}
@opindex Wctor-dtor-privacy
Warn when a class seems unusable, because all the constructors or
destructors in a class are private and the class has no friends or
public static member functions.

@item -Wnon-virtual-dtor @r{(C++ only)}
@opindex Wnon-virtual-dtor
Warn when a class declares a non-virtual destructor that should probably
be virtual, because it looks like the class will be used polymorphically.
This warning is enabled by @option{-Wall}.

@item -Wreorder @r{(C++ only)}
@opindex Wreorder
@cindex reordering, warning
@cindex warning for reordering of member initializers
Warn when the order of member initializers given in the code does not
match the order in which they must be executed.  For instance:

@smallexample
struct A @{
  int i;
  int j;
  A(): j (0), i (1) @{ @}
@};
@end smallexample

Here the compiler will warn that the member initializers for @samp{i}
and @samp{j} will be rearranged to match the declaration order of the
members.  This warning is enabled by @option{-Wall}.
@end table

The following @option{-W@dots{}} options are not affected by @option{-Wall}.

@table @gcctabopt
@item -Weffc++ @r{(C++ only)}
@opindex Weffc++
Warn about violations of the following style guidelines from Scott Meyers'
@cite{Effective C++} book:

@itemize @bullet
@item
Item 11:  Define a copy constructor and an assignment operator for classes
with dynamically allocated memory.

@item
Item 12:  Prefer initialization to assignment in constructors.

@item
Item 14:  Make destructors virtual in base classes.

@item
Item 15:  Have @code{operator=} return a reference to @code{*this}.

@item
Item 23:  Don't try to return a reference when you must return an object.

@end itemize

and about violations of the following style guidelines from Scott Meyers'
@cite{More Effective C++} book:

@itemize @bullet
@item
Item 6:  Distinguish between prefix and postfix forms of increment and
decrement operators.

@item
Item 7:  Never overload @code{&&}, @code{||}, or @code{,}.

@end itemize

If you use this option, you should be aware that the standard library
headers do not obey all of these guidelines; you can use @samp{grep -v}
to filter out those warnings.

@item -Wno-deprecated @r{(C++ only)}
@opindex Wno-deprecated
Do not warn about usage of deprecated features.  @xref{Deprecated Features}.

@item -Wno-non-template-friend @r{(C++ only)}
@opindex Wno-non-template-friend
Disable warnings when non-templatized friend functions are declared
within a template.  With the advent of explicit template specification
support in G++, if the name of the friend is an unqualified-id (i.e.,
@samp{friend foo(int)}), the C++ language specification demands that the
friend declare or define an ordinary, nontemplate function.  (Section
14.5.3).  Before G++ implemented explicit specification, unqualified-ids
could be interpreted as a particular specialization of a templatized
function.  Because this non-conforming behavior is no longer the default
behavior for G++, @option{-Wnon-template-friend} allows the compiler to
check existing code for potential trouble spots, and is on by default.
This new compiler behavior can be turned off with
@option{-Wno-non-template-friend} which keeps the conformant compiler code
but disables the helpful warning.

@item -Wold-style-cast @r{(C++ only)}
@opindex Wold-style-cast
Warn if an old-style (C-style) cast to a non-void type is used within
a C++ program.  The new-style casts (@samp{static_cast},
@samp{reinterpret_cast}, and @samp{const_cast}) are less vulnerable to
unintended effects, and much easier to grep for.

@item -Woverloaded-virtual @r{(C++ only)}
@opindex Woverloaded-virtual
@cindex overloaded virtual fn, warning
@cindex warning for overloaded virtual fn
Warn when a function declaration hides virtual functions from a
base class.  For example, in:

@smallexample
struct A @{
  virtual void f();
@};

struct B: public A @{
  void f(int);
@};
@end smallexample

the @code{A} class version of @code{f} is hidden in @code{B}, and code
like this:

@smallexample
B* b;
b->f();
@end smallexample

will fail to compile.

@item -Wno-pmf-conversions @r{(C++ only)}
@opindex Wno-pmf-conversions
Disable the diagnostic for converting a bound pointer to member function
to a plain pointer.

@item -Wsign-promo @r{(C++ only)}
@opindex Wsign-promo
Warn when overload resolution chooses a promotion from unsigned or
enumeral type to a signed type over a conversion to an unsigned type of
the same size.  Previous versions of G++ would try to preserve
unsignedness, but the standard mandates the current behavior.

@item -Wsynth @r{(C++ only)}
@opindex Wsynth
@cindex warning for synthesized methods
@cindex synthesized methods, warning
Warn when G++'s synthesis behavior does not match that of cfront.  For
instance:

@smallexample
struct A @{
  operator int ();
  A& operator = (int);
@};

main ()
@{
  A a,b;
  a = b;
@}
@end smallexample

In this example, G++ will synthesize a default @samp{A& operator =
(const A&);}, while cfront will use the user-defined @samp{operator =}.
@end table

@node Objective-C Dialect Options
@section Options Controlling Objective-C Dialect

@cindex compiler options, Objective-C
@cindex Objective-C options, command line
@cindex options, Objective-C
This section describes the command-line options that are only meaningful
for Objective-C programs; but you can also use most of the GNU compiler
options regardless of what language your program is in.  For example,
you might compile a file @code{some_class.m} like this:

@example
gcc -g -fgnu-runtime -O -c some_class.m
@end example

@noindent
In this example, only @option{-fgnu-runtime} is an option meant only for
Objective-C programs; you can use the other options with any language
supported by GCC@.

Here is a list of options that are @emph{only} for compiling Objective-C
programs:

@table @gcctabopt
@item -fconstant-string-class=@var{class-name}
@opindex fconstant-string-class
Use @var{class-name} as the name of the class to instantiate for each
literal string specified with the syntax @code{@@"@dots{}"}.  The default
class name is @code{NXConstantString}.

@item -fgnu-runtime
@opindex fgnu-runtime
Generate object code compatible with the standard GNU Objective-C
runtime.  This is the default for most types of systems.

@item -fnext-runtime
@opindex fnext-runtime
Generate output compatible with the NeXT runtime.  This is the default
for NeXT-based systems, including Darwin and Mac OS X@.  The macro
@code{__NEXT_RUNTIME__} is predefined if (and only if) this option is
used.

@item -gen-decls
@opindex gen-decls
Dump interface declarations for all classes seen in the source file to a
file named @file{@var{sourcename}.decl}.

@item -Wno-protocol
@opindex Wno-protocol
If a class is declared to implement a protocol, a warning is issued for
every method in the protocol that is not implemented by the class.  The
default behavior is to issue a warning for every method not explicitly
implemented in the class, even if a method implementation is inherited
from the superclass.  If you use the @code{-Wno-protocol} option, then
methods inherited from the superclass are considered to be implemented,
and no warning is issued for them.

@item -Wselector
@opindex Wselector
Warn if multiple methods of different types for the same selector are
found during compilation.  The check is performed on the list of methods
in the final stage of compilation.  Additionally, a check is performed
that for each selector appearing in a @code{@@selector(@dots{})}
expression, a corresponding method with that selector has been found
during compilation.  Because these checks scan the method table only at
the end of compilation, these warnings are not produced if the final
stage of compilation is not reached, for example because an error is
found during compilation, or because the @code{-fsyntax-only} option is
being used.

@item -Wundeclared-selector
@opindex Wundeclared-selector
Warn if a @code{@@selector(@dots{})} expression referring to an
undeclared selector is found.  A selector is considered undeclared if no
method with that name has been declared (explicitly, in an
@code{@@interface} or @code{@@protocol} declaration, or implicitly, in
an @code{@@implementation} section) before the
@code{@@selector(@dots{})} expression.  This option always performs its
checks as soon as a @code{@@selector(@dots{})} expression is found
(while @code{-Wselector} only performs its checks in the final stage of
compilation), and so additionally enforces the coding style convention
that methods and selectors must be declared before being used.

@c not documented because only avail via -Wp
@c @item -print-objc-runtime-info

@end table

@node Language Independent Options
@section Options to Control Diagnostic Messages Formatting
@cindex options to control diagnostics formatting
@cindex diagnostic messages
@cindex message formatting

Traditionally, diagnostic messages have been formatted irrespective of
the output device's aspect (e.g.@: its width, @dots{}).  The options described
below can be used to control the diagnostic messages formatting
algorithm, e.g.@: how many characters per line, how often source location
information should be reported.  Right now, only the C++ front end can
honor these options.  However it is expected, in the near future, that
the remaining front ends would be able to digest them correctly.

@table @gcctabopt
@item -fmessage-length=@var{n}
@opindex fmessage-length
Try to format error messages so that they fit on lines of about @var{n}
characters.  The default is 72 characters for @command{g++} and 0 for the rest of
the front ends supported by GCC@.  If @var{n} is zero, then no
line-wrapping will be done; each error message will appear on a single
line.

@opindex fdiagnostics-show-location
@item -fdiagnostics-show-location=once
Only meaningful in line-wrapping mode.  Instructs the diagnostic messages
reporter to emit @emph{once} source location information; that is, in
case the message is too long to fit on a single physical line and has to
be wrapped, the source location won't be emitted (as prefix) again,
over and over, in subsequent continuation lines.  This is the default
behavior.

@item -fdiagnostics-show-location=every-line
Only meaningful in line-wrapping mode.  Instructs the diagnostic
messages reporter to emit the same source location information (as
prefix) for physical lines that result from the process of breaking
a message which is too long to fit on a single line.

@end table

@node Warning Options
@section Options to Request or Suppress Warnings
@cindex options to control warnings
@cindex warning messages
@cindex messages, warning
@cindex suppressing warnings

Warnings are diagnostic messages that report constructions which
are not inherently erroneous but which are risky or suggest there
may have been an error.

You can request many specific warnings with options beginning @samp{-W},
for example @option{-Wimplicit} to request warnings on implicit
declarations.  Each of these specific warning options also has a
negative form beginning @samp{-Wno-} to turn off warnings;
for example, @option{-Wno-implicit}.  This manual lists only one of the
two forms, whichever is not the default.

The following options control the amount and kinds of warnings produced
by GCC; for further, language-specific options also refer to
@ref{C++ Dialect Options} and @ref{Objective-C Dialect Options}.

@table @gcctabopt
@cindex syntax checking
@item -fsyntax-only
@opindex fsyntax-only
Check the code for syntax errors, but don't do anything beyond that.

@item -pedantic
@opindex pedantic
Issue all the warnings demanded by strict ISO C and ISO C++;
reject all programs that use forbidden extensions, and some other
programs that do not follow ISO C and ISO C++.  For ISO C, follows the
version of the ISO C standard specified by any @option{-std} option used.

Valid ISO C and ISO C++ programs should compile properly with or without
this option (though a rare few will require @option{-ansi} or a
@option{-std} option specifying the required version of ISO C)@.  However,
without this option, certain GNU extensions and traditional C and C++
features are supported as well.  With this option, they are rejected.

@option{-pedantic} does not cause warning messages for use of the
alternate keywords whose names begin and end with @samp{__}.  Pedantic
warnings are also disabled in the expression that follows
@code{__extension__}.  However, only system header files should use
these escape routes; application programs should avoid them.
@xref{Alternate Keywords}.

Some users try to use @option{-pedantic} to check programs for strict ISO
C conformance.  They soon find that it does not do quite what they want:
it finds some non-ISO practices, but not all---only those for which
ISO C @emph{requires} a diagnostic, and some others for which
diagnostics have been added.

A feature to report any failure to conform to ISO C might be useful in
some instances, but would require considerable additional work and would
be quite different from @option{-pedantic}.  We don't have plans to
support such a feature in the near future.

Where the standard specified with @option{-std} represents a GNU
extended dialect of C, such as @samp{gnu89} or @samp{gnu99}, there is a
corresponding @dfn{base standard}, the version of ISO C on which the GNU
extended dialect is based.  Warnings from @option{-pedantic} are given
where they are required by the base standard.  (It would not make sense
for such warnings to be given only for features not in the specified GNU
C dialect, since by definition the GNU dialects of C include all
features the compiler supports with the given option, and there would be
nothing to warn about.)

@item -pedantic-errors
@opindex pedantic-errors
Like @option{-pedantic}, except that errors are produced rather than
warnings.

@item -w
@opindex w
Inhibit all warning messages.

@item -Wno-import
@opindex Wno-import
Inhibit warning messages about the use of @samp{#import}.

@item -Wchar-subscripts
@opindex Wchar-subscripts
Warn if an array subscript has type @code{char}.  This is a common cause
of error, as programmers often forget that this type is signed on some
machines.

@item -Wcomment
@opindex Wcomment
Warn whenever a comment-start sequence @samp{/*} appears in a @samp{/*}
comment, or whenever a Backslash-Newline appears in a @samp{//} comment.

@item -Wformat
@opindex Wformat
Check calls to @code{printf} and @code{scanf}, etc., to make sure that
the arguments supplied have types appropriate to the format string
specified, and that the conversions specified in the format string make
sense.  This includes standard functions, and others specified by format
attributes (@pxref{Function Attributes}), in the @code{printf},
@code{scanf}, @code{strftime} and @code{strfmon} (an X/Open extension,
not in the C standard) families.

The formats are checked against the format features supported by GNU
libc version 2.2.  These include all ISO C90 and C99 features, as well
as features from the Single Unix Specification and some BSD and GNU
extensions.  Other library implementations may not support all these
features; GCC does not support warning about features that go beyond a
particular library's limitations.  However, if @option{-pedantic} is used
with @option{-Wformat}, warnings will be given about format features not
in the selected standard version (but not for @code{strfmon} formats,
since those are not in any version of the C standard).  @xref{C Dialect
Options,,Options Controlling C Dialect}.

Since @option{-Wformat} also checks for null format arguments for
several functions, @option{-Wformat} also implies @option{-Wnonnull}.

@option{-Wformat} is included in @option{-Wall}.  For more control over some
aspects of format checking, the options @option{-Wno-format-y2k},
@option{-Wno-format-extra-args}, @option{-Wno-format-zero-length},
@option{-Wformat-nonliteral}, @option{-Wformat-security}, and
@option{-Wformat=2} are available, but are not included in @option{-Wall}.

@item -Wno-format-y2k
@opindex Wno-format-y2k
If @option{-Wformat} is specified, do not warn about @code{strftime}
formats which may yield only a two-digit year.

@item -Wno-format-extra-args
@opindex Wno-format-extra-args
If @option{-Wformat} is specified, do not warn about excess arguments to a
@code{printf} or @code{scanf} format function.  The C standard specifies
that such arguments are ignored.

Where the unused arguments lie between used arguments that are
specified with @samp{$} operand number specifications, normally
warnings are still given, since the implementation could not know what
type to pass to @code{va_arg} to skip the unused arguments.  However,
in the case of @code{scanf} formats, this option will suppress the
warning if the unused arguments are all pointers, since the Single
Unix Specification says that such unused arguments are allowed.

@item -Wno-format-zero-length
@opindex Wno-format-zero-length
If @option{-Wformat} is specified, do not warn about zero-length formats.
The C standard specifies that zero-length formats are allowed.

@item -Wformat-nonliteral
@opindex Wformat-nonliteral
If @option{-Wformat} is specified, also warn if the format string is not a
string literal and so cannot be checked, unless the format function
takes its format arguments as a @code{va_list}.

@item -Wformat-security
@opindex Wformat-security
If @option{-Wformat} is specified, also warn about uses of format
functions that represent possible security problems.  At present, this
warns about calls to @code{printf} and @code{scanf} functions where the
format string is not a string literal and there are no format arguments,
as in @code{printf (foo);}.  This may be a security hole if the format
string came from untrusted input and contains @samp{%n}.  (This is
currently a subset of what @option{-Wformat-nonliteral} warns about, but
in future warnings may be added to @option{-Wformat-security} that are not
included in @option{-Wformat-nonliteral}.)

@item -Wformat=2
@opindex Wformat=2
Enable @option{-Wformat} plus format checks not included in
@option{-Wformat}.  Currently equivalent to @samp{-Wformat
-Wformat-nonliteral -Wformat-security}.

@item -Wnonnull
@opindex Wnonnull
Enable warning about passing a null pointer for arguments marked as
requiring a non-null value by the @code{nonnull} function attribute.

@option{-Wnonnull} is included in @option{-Wall} and @option{-Wformat}.  It
can be disabled with the @option{-Wno-nonnull} option.

@item -Wimplicit-int
@opindex Wimplicit-int
Warn when a declaration does not specify a type.

@item -Wimplicit-function-declaration
@itemx -Werror-implicit-function-declaration
@opindex Wimplicit-function-declaration
@opindex Werror-implicit-function-declaration
Give a warning (or error) whenever a function is used before being
declared.

@item -Wimplicit
@opindex Wimplicit
Same as @option{-Wimplicit-int} and @option{-Wimplicit-function-declaration}.

@item -Wmain
@opindex Wmain
Warn if the type of @samp{main} is suspicious.  @samp{main} should be a
function with external linkage, returning int, taking either zero
arguments, two, or three arguments of appropriate types.

@item -Wmissing-braces
@opindex Wmissing-braces
Warn if an aggregate or union initializer is not fully bracketed.  In
the following example, the initializer for @samp{a} is not fully
bracketed, but that for @samp{b} is fully bracketed.

@smallexample
int a[2][2] = @{ 0, 1, 2, 3 @};
int b[2][2] = @{ @{ 0, 1 @}, @{ 2, 3 @} @};
@end smallexample

@item -Wparentheses
@opindex Wparentheses
Warn if parentheses are omitted in certain contexts, such
as when there is an assignment in a context where a truth value
is expected, or when operators are nested whose precedence people
often get confused about.

Also warn about constructions where there may be confusion to which
@code{if} statement an @code{else} branch belongs.  Here is an example of
such a case:

@smallexample
@group
@{
  if (a)
    if (b)
      foo ();
  else
    bar ();
@}
@end group
@end smallexample

In C, every @code{else} branch belongs to the innermost possible @code{if}
statement, which in this example is @code{if (b)}.  This is often not
what the programmer expected, as illustrated in the above example by
indentation the programmer chose.  When there is the potential for this
confusion, GCC will issue a warning when this flag is specified.
To eliminate the warning, add explicit braces around the innermost
@code{if} statement so there is no way the @code{else} could belong to
the enclosing @code{if}.  The resulting code would look like this:

@smallexample
@group
@{
  if (a)
    @{
      if (b)
        foo ();
      else
        bar ();
    @}
@}
@end group
@end smallexample

@item -Wsequence-point
@opindex Wsequence-point
Warn about code that may have undefined semantics because of violations
of sequence point rules in the C standard.

The C standard defines the order in which expressions in a C program are
evaluated in terms of @dfn{sequence points}, which represent a partial
ordering between the execution of parts of the program: those executed
before the sequence point, and those executed after it.  These occur
after the evaluation of a full expression (one which is not part of a
larger expression), after the evaluation of the first operand of a
@code{&&}, @code{||}, @code{? :} or @code{,} (comma) operator, before a
function is called (but after the evaluation of its arguments and the
expression denoting the called function), and in certain other places.
Other than as expressed by the sequence point rules, the order of
evaluation of subexpressions of an expression is not specified.  All
these rules describe only a partial order rather than a total order,
since, for example, if two functions are called within one expression
with no sequence point between them, the order in which the functions
are called is not specified.  However, the standards committee have
ruled that function calls do not overlap.

It is not specified when between sequence points modifications to the
values of objects take effect.  Programs whose behavior depends on this
have undefined behavior; the C standard specifies that ``Between the
previous and next sequence point an object shall have its stored value
modified at most once by the evaluation of an expression.  Furthermore,
the prior value shall be read only to determine the value to be
stored.''.  If a program breaks these rules, the results on any
particular implementation are entirely unpredictable.

Examples of code with undefined behavior are @code{a = a++;}, @code{a[n]
= b[n++]} and @code{a[i++] = i;}.  Some more complicated cases are not
diagnosed by this option, and it may give an occasional false positive
result, but in general it has been found fairly effective at detecting
this sort of problem in programs.

The present implementation of this option only works for C programs.  A
future implementation may also work for C++ programs.

The C standard is worded confusingly, therefore there is some debate
over the precise meaning of the sequence point rules in subtle cases.
Links to discussions of the problem, including proposed formal
definitions, may be found on our readings page, at
@w{@uref{http://gcc.gnu.org/readings.html}}.

@item -Wreturn-type
@opindex Wreturn-type
Warn whenever a function is defined with a return-type that defaults to
@code{int}.  Also warn about any @code{return} statement with no
return-value in a function whose return-type is not @code{void}.

For C++, a function without return type always produces a diagnostic
message, even when @option{-Wno-return-type} is specified.  The only
exceptions are @samp{main} and functions defined in system headers.

@item -Wswitch
@opindex Wswitch
Warn whenever a @code{switch} statement has an index of enumeral type
and lacks a @code{case} for one or more of the named codes of that
enumeration.  (The presence of a @code{default} label prevents this
warning.)  @code{case} labels outside the enumeration range also
provoke warnings when this option is used.

@item -Wswitch-default
@opindex Wswitch-switch
Warn whenever a @code{switch} statement does not have a @code{default}
case.

@item -Wswitch-enum
@opindex Wswitch-enum
Warn whenever a @code{switch} statement has an index of enumeral type
and lacks a @code{case} for one or more of the named codes of that
enumeration.  @code{case} labels outside the enumeration range also
provoke warnings when this option is used.

@item -Wtrigraphs
@opindex Wtrigraphs
Warn if any trigraphs are encountered that might change the meaning of
the program (trigraphs within comments are not warned about).

@item -Wunused-function
@opindex Wunused-function
Warn whenever a static function is declared but not defined or a
non\-inline static function is unused.

@item -Wunused-label
@opindex Wunused-label
Warn whenever a label is declared but not used.

To suppress this warning use the @samp{unused} attribute
(@pxref{Variable Attributes}).

@item -Wunused-parameter
@opindex Wunused-parameter
Warn whenever a function parameter is unused aside from its declaration.

To suppress this warning use the @samp{unused} attribute
(@pxref{Variable Attributes}).

@item -Wunused-variable
@opindex Wunused-variable
Warn whenever a local variable or non-constant static variable is unused
aside from its declaration

To suppress this warning use the @samp{unused} attribute
(@pxref{Variable Attributes}).

@item -Wunused-value
@opindex Wunused-value
Warn whenever a statement computes a result that is explicitly not used.

To suppress this warning cast the expression to @samp{void}.

@item -Wunused
@opindex Wunused
All the above @option{-Wunused} options combined.

In order to get a warning about an unused function parameter, you must
either specify @samp{-Wextra -Wunused} (note that @samp{-Wall} implies
@samp{-Wunused}), or separately specify @option{-Wunused-parameter}.

@item -Wuninitialized
@opindex Wuninitialized
Warn if an automatic variable is used without first being initialized or
if a variable may be clobbered by a @code{setjmp} call.

These warnings are possible only in optimizing compilation,
because they require data flow information that is computed only
when optimizing.  If you don't specify @option{-O}, you simply won't
get these warnings.

These warnings occur only for variables that are candidates for
register allocation.  Therefore, they do not occur for a variable that
is declared @code{volatile}, or whose address is taken, or whose size
is other than 1, 2, 4 or 8 bytes.  Also, they do not occur for
structures, unions or arrays, even when they are in registers.

Note that there may be no warning about a variable that is used only
to compute a value that itself is never used, because such
computations may be deleted by data flow analysis before the warnings
are printed.

These warnings are made optional because GCC is not smart
enough to see all the reasons why the code might be correct
despite appearing to have an error.  Here is one example of how
this can happen:

@smallexample
@group
@{
  int x;
  switch (y)
    @{
    case 1: x = 1;
      break;
    case 2: x = 4;
      break;
    case 3: x = 5;
    @}
  foo (x);
@}
@end group
@end smallexample

@noindent
If the value of @code{y} is always 1, 2 or 3, then @code{x} is
always initialized, but GCC doesn't know this.  Here is
another common case:

@smallexample
@{
  int save_y;
  if (change_y) save_y = y, y = new_y;
  @dots{}
  if (change_y) y = save_y;
@}
@end smallexample

@noindent
This has no bug because @code{save_y} is used only if it is set.

@cindex @code{longjmp} warnings
This option also warns when a non-volatile automatic variable might be
changed by a call to @code{longjmp}.  These warnings as well are possible
only in optimizing compilation.

The compiler sees only the calls to @code{setjmp}.  It cannot know
where @code{longjmp} will be called; in fact, a signal handler could
call it at any point in the code.  As a result, you may get a warning
even when there is in fact no problem because @code{longjmp} cannot
in fact be called at the place which would cause a problem.

Some spurious warnings can be avoided if you declare all the functions
you use that never return as @code{noreturn}.  @xref{Function
Attributes}.

@item -Wunknown-pragmas
@opindex Wunknown-pragmas
@cindex warning for unknown pragmas
@cindex unknown pragmas, warning
@cindex pragmas, warning of unknown
Warn when a #pragma directive is encountered which is not understood by
GCC@.  If this command line option is used, warnings will even be issued
for unknown pragmas in system header files.  This is not the case if
the warnings were only enabled by the @option{-Wall} command line option.

@item -Wstrict-aliasing
@opindex Wstrict-aliasing
This option is only active when @option{-fstrict-aliasing} is active.
It warns about code which might break the strict aliasing rules that the
compiler is using for optimization. The warning does not catch all
cases, but does attempt to catch the more common pitfalls. It is
included in @option{-Wall}.

@item -Wall
@opindex Wall
All of the above @samp{-W} options combined.  This enables all the
warnings about constructions that some users consider questionable, and
that are easy to avoid (or modify to prevent the warning), even in
conjunction with macros.  This also enables some language-specific
warnings described in @ref{C++ Dialect Options} and
@ref{Objective-C Dialect Options}.
@end table

The following @option{-W@dots{}} options are not implied by @option{-Wall}.
Some of them warn about constructions that users generally do not
consider questionable, but which occasionally you might wish to check
for; others warn about constructions that are necessary or hard to avoid
in some cases, and there is no simple way to modify the code to suppress
the warning.

@table @gcctabopt
@item -Wextra
@opindex W
@opindex Wextra
(This option used to be called @option{-W}.  The older name is still
supported, but the newer name is more descriptive.)  Print extra warning
messages for these events:

@itemize @bullet
@item
A function can return either with or without a value.  (Falling
off the end of the function body is considered returning without
a value.)  For example, this function would evoke such a
warning:

@smallexample
@group
foo (a)
@{
  if (a > 0)
    return a;
@}
@end group
@end smallexample

@item
An expression-statement or the left-hand side of a comma expression
contains no side effects.
To suppress the warning, cast the unused expression to void.
For example, an expression such as @samp{x[i,j]} will cause a warning,
but @samp{x[(void)i,j]} will not.

@item
An unsigned value is compared against zero with @samp{<} or @samp{>=}.

@item
A comparison like @samp{x<=y<=z} appears; this is equivalent to
@samp{(x<=y ? 1 : 0) <= z}, which is a different interpretation from
that of ordinary mathematical notation.

@item
Storage-class specifiers like @code{static} are not the first things in
a declaration.  According to the C Standard, this usage is obsolescent.

@item
The return type of a function has a type qualifier such as @code{const}.
Such a type qualifier has no effect, since the value returned by a
function is not an lvalue.  (But don't warn about the GNU extension of
@code{volatile void} return types.  That extension will be warned about
if @option{-pedantic} is specified.)

@item
If @option{-Wall} or @option{-Wunused} is also specified, warn about unused
arguments.

@item
A comparison between signed and unsigned values could produce an
incorrect result when the signed value is converted to unsigned.
(But don't warn if @option{-Wno-sign-compare} is also specified.)

@item
An aggregate has an initializer which does not initialize all members.
For example, the following code would cause such a warning, because
@code{x.h} would be implicitly initialized to zero:

@smallexample
struct s @{ int f, g, h; @};
struct s x = @{ 3, 4 @};
@end smallexample

@item
A function parameter is declared without a type specifier in K&R-style
functions:

@smallexample
void foo(bar) @{ @}
@end smallexample

@item
An empty body occurs in an @samp{if} or @samp{else} statement.

@item
A pointer is compared against integer zero with @samp{<}, @samp{<=},
@samp{>}, or @samp{>=}.

@item
A variable might be changed by @samp{longjmp} or @samp{vfork}.

@item
Any of several floating-point events that often indicate errors, such as
overflow, underflow, loss of precision, etc.

@item @r{(C++ only)}
An enumerator and a non-enumerator both appear in a conditional expression.

@item @r{(C++ only)}
A non-static reference or non-static @samp{const} member appears in a
class without constructors.

@item @r{(C++ only)}
Ambiguous virtual bases.

@item @r{(C++ only)}
Subscripting an array which has been declared @samp{register}.

@item @r{(C++ only)}
Taking the address of a variable which has been declared @samp{register}.

@item @r{(C++ only)}
A base class is not initialized in a derived class' copy constructor.
@end itemize

@item -Wno-div-by-zero
@opindex Wno-div-by-zero
@opindex Wdiv-by-zero
Do not warn about compile-time integer division by zero.  Floating point
division by zero is not warned about, as it can be a legitimate way of
obtaining infinities and NaNs.

@item -Wsystem-headers
@opindex Wsystem-headers
@cindex warnings from system headers
@cindex system headers, warnings from
Print warning messages for constructs found in system header files.
Warnings from system headers are normally suppressed, on the assumption
that they usually do not indicate real problems and would only make the
compiler output harder to read.  Using this command line option tells
GCC to emit warnings from system headers as if they occurred in user
code.  However, note that using @option{-Wall} in conjunction with this
option will @emph{not} warn about unknown pragmas in system
headers---for that, @option{-Wunknown-pragmas} must also be used.

@item -Wfloat-equal
@opindex Wfloat-equal
Warn if floating point values are used in equality comparisons.

The idea behind this is that sometimes it is convenient (for the
programmer) to consider floating-point values as approximations to
infinitely precise real numbers.  If you are doing this, then you need
to compute (by analyzing the code, or in some other way) the maximum or
likely maximum error that the computation introduces, and allow for it
when performing comparisons (and when producing output, but that's a
different problem).  In particular, instead of testing for equality, you
would check to see whether the two values have ranges that overlap; and
this is done with the relational operators, so equality comparisons are
probably mistaken.

@item -Wtraditional @r{(C only)}
@opindex Wtraditional
Warn about certain constructs that behave differently in traditional and
ISO C@.  Also warn about ISO C constructs that have no traditional C
equivalent, and/or problematic constructs which should be avoided.

@itemize @bullet
@item
Macro parameters that appear within string literals in the macro body.
In traditional C macro replacement takes place within string literals,
but does not in ISO C@.

@item
In traditional C, some preprocessor directives did not exist.
Traditional preprocessors would only consider a line to be a directive
if the @samp{#} appeared in column 1 on the line.  Therefore
@option{-Wtraditional} warns about directives that traditional C
understands but would ignore because the @samp{#} does not appear as the
first character on the line.  It also suggests you hide directives like
@samp{#pragma} not understood by traditional C by indenting them.  Some
traditional implementations would not recognize @samp{#elif}, so it
suggests avoiding it altogether.

@item
A function-like macro that appears without arguments.

@item
The unary plus operator.

@item
The @samp{U} integer constant suffix, or the @samp{F} or @samp{L} floating point
constant suffixes.  (Traditional C does support the @samp{L} suffix on integer
constants.)  Note, these suffixes appear in macros defined in the system
headers of most modern systems, e.g.@: the @samp{_MIN}/@samp{_MAX} macros in @code{<limits.h>}.
Use of these macros in user code might normally lead to spurious
warnings, however gcc's integrated preprocessor has enough context to
avoid warning in these cases.

@item
A function declared external in one block and then used after the end of
the block.

@item
A @code{switch} statement has an operand of type @code{long}.

@item
A non-@code{static} function declaration follows a @code{static} one.
This construct is not accepted by some traditional C compilers.

@item
The ISO type of an integer constant has a different width or
signedness from its traditional type.  This warning is only issued if
the base of the constant is ten.  I.e.@: hexadecimal or octal values, which
typically represent bit patterns, are not warned about.

@item
Usage of ISO string concatenation is detected.

@item
Initialization of automatic aggregates.

@item
Identifier conflicts with labels.  Traditional C lacks a separate
namespace for labels.

@item
Initialization of unions.  If the initializer is zero, the warning is
omitted.  This is done under the assumption that the zero initializer in
user code appears conditioned on e.g.@: @code{__STDC__} to avoid missing
initializer warnings and relies on default initialization to zero in the
traditional C case.

@item
Conversions by prototypes between fixed/floating point values and vice
versa.  The absence of these prototypes when compiling with traditional
C would cause serious problems.  This is a subset of the possible
conversion warnings, for the full set use @option{-Wconversion}.

@item
Use of ISO C style function definitions.  This warning intentionally is
@emph{not} issued for prototype declarations or variadic functions
because these ISO C features will appear in your code when using
libiberty's traditional C compatibility macros, @code{PARAMS} and
@code{VPARAMS}.  This warning is also bypassed for nested functions
because that feature is already a gcc extension and thus not relevant to
traditional C compatibility.
@end itemize

@item -Wundef
@opindex Wundef
Warn if an undefined identifier is evaluated in an @samp{#if} directive.

@item -Wendif-labels
@opindex Wendif-labels
Warn whenever an @samp{#else} or an @samp{#endif} are followed by text.

@item -Wshadow
@opindex Wshadow
Warn whenever a local variable shadows another local variable, parameter or
global variable or whenever a built-in function is shadowed.

@item -Wlarger-than-@var{len}
@opindex Wlarger-than
Warn whenever an object of larger than @var{len} bytes is defined.

@item -Wpointer-arith
@opindex Wpointer-arith
Warn about anything that depends on the ``size of'' a function type or
of @code{void}.  GNU C assigns these types a size of 1, for
convenience in calculations with @code{void *} pointers and pointers
to functions.

@item -Wbad-function-cast @r{(C only)}
@opindex Wbad-function-cast
Warn whenever a function call is cast to a non-matching type.
For example, warn if @code{int malloc()} is cast to @code{anything *}.

@item -Wcast-qual
@opindex Wcast-qual
Warn whenever a pointer is cast so as to remove a type qualifier from
the target type.  For example, warn if a @code{const char *} is cast
to an ordinary @code{char *}.

@item -Wcast-align
@opindex Wcast-align
Warn whenever a pointer is cast such that the required alignment of the
target is increased.  For example, warn if a @code{char *} is cast to
an @code{int *} on machines where integers can only be accessed at
two- or four-byte boundaries.

@item -Wwrite-strings
@opindex Wwrite-strings
When compiling C, give string constants the type @code{const
char[@var{length}]} so that
copying the address of one into a non-@code{const} @code{char *}
pointer will get a warning; when compiling C++, warn about the
deprecated conversion from string constants to @code{char *}.
These warnings will help you find at
compile time code that can try to write into a string constant, but
only if you have been very careful about using @code{const} in
declarations and prototypes.  Otherwise, it will just be a nuisance;
this is why we did not make @option{-Wall} request these warnings.

@item -Wconversion
@opindex Wconversion
Warn if a prototype causes a type conversion that is different from what
would happen to the same argument in the absence of a prototype.  This
includes conversions of fixed point to floating and vice versa, and
conversions changing the width or signedness of a fixed point argument
except when the same as the default promotion.

Also, warn if a negative integer constant expression is implicitly
converted to an unsigned type.  For example, warn about the assignment
@code{x = -1} if @code{x} is unsigned.  But do not warn about explicit
casts like @code{(unsigned) -1}.

@item -Wsign-compare
@opindex Wsign-compare
@cindex warning for comparison of signed and unsigned values
@cindex comparison of signed and unsigned values, warning
@cindex signed and unsigned values, comparison warning
Warn when a comparison between signed and unsigned values could produce
an incorrect result when the signed value is converted to unsigned.
This warning is also enabled by @option{-Wextra}; to get the other warnings
of @option{-Wextra} without this warning, use @samp{-Wextra -Wno-sign-compare}.

@item -Waggregate-return
@opindex Waggregate-return
Warn if any functions that return structures or unions are defined or
called.  (In languages where you can return an array, this also elicits
a warning.)

@item -Wstrict-prototypes @r{(C only)}
@opindex Wstrict-prototypes
Warn if a function is declared or defined without specifying the
argument types.  (An old-style function definition is permitted without
a warning if preceded by a declaration which specifies the argument
types.)

@item -Wmissing-prototypes @r{(C only)}
@opindex Wmissing-prototypes
Warn if a global function is defined without a previous prototype
declaration.  This warning is issued even if the definition itself
provides a prototype.  The aim is to detect global functions that fail
to be declared in header files.

@item -Wmissing-declarations @r{(C only)}
@opindex Wmissing-declarations
Warn if a global function is defined without a previous declaration.
Do so even if the definition itself provides a prototype.
Use this option to detect global functions that are not declared in
header files.

@item -Wmissing-noreturn
@opindex Wmissing-noreturn
Warn about functions which might be candidates for attribute @code{noreturn}.
Note these are only possible candidates, not absolute ones.  Care should
be taken to manually verify functions actually do not ever return before
adding the @code{noreturn} attribute, otherwise subtle code generation
bugs could be introduced.  You will not get a warning for @code{main} in
hosted C environments.

@item -Wmissing-format-attribute
@opindex Wmissing-format-attribute
@opindex Wformat
If @option{-Wformat} is enabled, also warn about functions which might be
candidates for @code{format} attributes.  Note these are only possible
candidates, not absolute ones.  GCC will guess that @code{format}
attributes might be appropriate for any function that calls a function
like @code{vprintf} or @code{vscanf}, but this might not always be the
case, and some functions for which @code{format} attributes are
appropriate may not be detected.  This option has no effect unless
@option{-Wformat} is enabled (possibly by @option{-Wall}).

@item -Wno-multichar
@opindex Wno-multichar
@opindex Wmultichar
Do not warn if a multicharacter constant (@samp{'FOOF'}) is used.
Usually they indicate a typo in the user's code, as they have
implementation-defined values, and should not be used in portable code.

@item -Wno-deprecated-declarations
@opindex Wno-deprecated-declarations
Do not warn about uses of functions, variables, and types marked as
deprecated by using the @code{deprecated} attribute.
(@pxref{Function Attributes}, @pxref{Variable Attributes},
@pxref{Type Attributes}.)

@item -Wpacked
@opindex Wpacked
Warn if a structure is given the packed attribute, but the packed
attribute has no effect on the layout or size of the structure.
Such structures may be mis-aligned for little benefit.  For
instance, in this code, the variable @code{f.x} in @code{struct bar}
will be misaligned even though @code{struct bar} does not itself
have the packed attribute:

@smallexample
@group
struct foo @{
  int x;
  char a, b, c, d;
@} __attribute__((packed));
struct bar @{
  char z;
  struct foo f;
@};
@end group
@end smallexample

@item -Wpadded
@opindex Wpadded
Warn if padding is included in a structure, either to align an element
of the structure or to align the whole structure.  Sometimes when this
happens it is possible to rearrange the fields of the structure to
reduce the padding and so make the structure smaller.

@item -Wredundant-decls
@opindex Wredundant-decls
Warn if anything is declared more than once in the same scope, even in
cases where multiple declaration is valid and changes nothing.

@item -Wnested-externs @r{(C only)}
@opindex Wnested-externs
Warn if an @code{extern} declaration is encountered within a function.

@item -Wunreachable-code
@opindex Wunreachable-code
Warn if the compiler detects that code will never be executed.

This option is intended to warn when the compiler detects that at
least a whole line of source code will never be executed, because
some condition is never satisfied or because it is after a
procedure that never returns.

It is possible for this option to produce a warning even though there
are circumstances under which part of the affected line can be executed,
so care should be taken when removing apparently-unreachable code.

For instance, when a function is inlined, a warning may mean that the
line is unreachable in only one inlined copy of the function.

This option is not made part of @option{-Wall} because in a debugging
version of a program there is often substantial code which checks
correct functioning of the program and is, hopefully, unreachable
because the program does work.  Another common use of unreachable
code is to provide behavior which is selectable at compile-time.

@item -Winline
@opindex Winline
Warn if a function can not be inlined and it was declared as inline.

@item -Wno-invalid-offsetof @r{(C++ only)}
@opindex Wno-invalid-offsetof
Suppress warnings from applying the @samp{offsetof} macro to a non-POD
type.  According to the 1998 ISO C++ standard, applying @samp{offsetof}
to a non-POD type is undefined.  In existing C++ implementations,
however, @samp{offsetof} typically gives meaningful results even when
applied to certain kinds of non-POD types. (Such as a simple
@samp{struct} that fails to be a POD type only by virtue of having a
constructor.)  This flag is for users who are aware that they are
writing nonportable code and who have deliberately chosen to ignore the
warning about it.

The restrictions on @samp{offsetof} may be relaxed in a future version
of the C++ standard.

@item -Winvalid-pch
@opindex Winvalid-pch
Warn if a precompiled header (@pxref{Precompiled Headers}) is found in
the search path but can't be used.

@item -Wlong-long
@opindex Wlong-long
@opindex Wno-long-long
Warn if @samp{long long} type is used.  This is default.  To inhibit
the warning messages, use @option{-Wno-long-long}.  Flags
@option{-Wlong-long} and @option{-Wno-long-long} are taken into account
only when @option{-pedantic} flag is used.

@item -Wdisabled-optimization
@opindex Wdisabled-optimization
Warn if a requested optimization pass is disabled.  This warning does
not generally indicate that there is anything wrong with your code; it
merely indicates that GCC's optimizers were unable to handle the code
effectively.  Often, the problem is that your code is too big or too
complex; GCC will refuse to optimize programs when the optimization
itself is likely to take inordinate amounts of time.

@item -Werror
@opindex Werror
Make all warnings into errors.
@end table

@node Debugging Options
@section Options for Debugging Your Program or GCC
@cindex options, debugging
@cindex debugging information options

GCC has various special options that are used for debugging
either your program or GCC:

@table @gcctabopt
@item -g
@opindex g
Produce debugging information in the operating system's native format
(stabs, COFF, XCOFF, or DWARF)@.  GDB can work with this debugging
information.

On most systems that use stabs format, @option{-g} enables use of extra
debugging information that only GDB can use; this extra information
makes debugging work better in GDB but will probably make other debuggers
crash or
refuse to read the program.  If you want to control for certain whether
to generate the extra information, use @option{-gstabs+}, @option{-gstabs},
@option{-gxcoff+}, @option{-gxcoff}, @option{-gdwarf-1+}, @option{-gdwarf-1},
or @option{-gvms} (see below).

Unlike most other C compilers, GCC allows you to use @option{-g} with
@option{-O}.  The shortcuts taken by optimized code may occasionally
produce surprising results: some variables you declared may not exist
at all; flow of control may briefly move where you did not expect it;
some statements may not be executed because they compute constant
results or their values were already at hand; some statements may
execute in different places because they were moved out of loops.

Nevertheless it proves possible to debug optimized output.  This makes
it reasonable to use the optimizer for programs that might have bugs.

The following options are useful when GCC is generated with the
capability for more than one debugging format.

@item -ggdb
@opindex ggdb
Produce debugging information for use by GDB@.  This means to use the
most expressive format available (DWARF 2, stabs, or the native format
if neither of those are supported), including GDB extensions if at all
possible.

@item -gstabs
@opindex gstabs
Produce debugging information in stabs format (if that is supported),
without GDB extensions.  This is the format used by DBX on most BSD
systems.  On MIPS, Alpha and System V Release 4 systems this option
produces stabs debugging output which is not understood by DBX or SDB@.
On System V Release 4 systems this option requires the GNU assembler.

@item -gstabs+
@opindex gstabs+
Produce debugging information in stabs format (if that is supported),
using GNU extensions understood only by the GNU debugger (GDB)@.  The
use of these extensions is likely to make other debuggers crash or
refuse to read the program.

@item -gcoff
@opindex gcoff
Produce debugging information in COFF format (if that is supported).
This is the format used by SDB on most System V systems prior to
System V Release 4.

@item -gxcoff
@opindex gxcoff
Produce debugging information in XCOFF format (if that is supported).
This is the format used by the DBX debugger on IBM RS/6000 systems.

@item -gxcoff+
@opindex gxcoff+
Produce debugging information in XCOFF format (if that is supported),
using GNU extensions understood only by the GNU debugger (GDB)@.  The
use of these extensions is likely to make other debuggers crash or
refuse to read the program, and may cause assemblers other than the GNU
assembler (GAS) to fail with an error.

@item -gdwarf
@opindex gdwarf
Produce debugging information in DWARF version 1 format (if that is
supported).  This is the format used by SDB on most System V Release 4
systems.

This option is deprecated.

@item -gdwarf+
@opindex gdwarf+
Produce debugging information in DWARF version 1 format (if that is
supported), using GNU extensions understood only by the GNU debugger
(GDB)@.  The use of these extensions is likely to make other debuggers
crash or refuse to read the program.

This option is deprecated.

@item -gdwarf-2
@opindex gdwarf-2
Produce debugging information in DWARF version 2 format (if that is
supported).  This is the format used by DBX on IRIX 6.

@item -gvms
@opindex gvms
Produce debugging information in VMS debug format (if that is
supported).  This is the format used by DEBUG on VMS systems.

@item -g@var{level}
@itemx -ggdb@var{level}
@itemx -gstabs@var{level}
@itemx -gcoff@var{level}
@itemx -gxcoff@var{level}
@itemx -gvms@var{level}
Request debugging information and also use @var{level} to specify how
much information.  The default level is 2.

Level 1 produces minimal information, enough for making backtraces in
parts of the program that you don't plan to debug.  This includes
descriptions of functions and external variables, but no information
about local variables and no line numbers.

Level 3 includes extra information, such as all the macro definitions
present in the program.  Some debuggers support macro expansion when
you use @option{-g3}.

Note that in order to avoid confusion between DWARF1 debug level 2,
and DWARF2, neither @option{-gdwarf} nor @option{-gdwarf-2} accept
a concatenated debug level.  Instead use an additional @option{-g@var{level}}
option to change the debug level for DWARF1 or DWARF2.

@item -feliminate-dwarf2-dups
@opindex feliminate-dwarf2-dups
Compress DWARF2 debugging information by eliminating duplicated
information about each symbol.  This option only makes sense when
generating DWARF2 debugging information with @option{-gdwarf-2}.

@cindex @command{prof}
@item -p
@opindex p
Generate extra code to write profile information suitable for the
analysis program @command{prof}.  You must use this option when compiling
the source files you want data about, and you must also use it when
linking.

@cindex @command{gprof}
@item -pg
@opindex pg
Generate extra code to write profile information suitable for the
analysis program @command{gprof}.  You must use this option when compiling
the source files you want data about, and you must also use it when
linking.

@item -Q
@opindex Q
Makes the compiler print out each function name as it is compiled, and
print some statistics about each pass when it finishes.

@item -ftime-report
@opindex ftime-report
Makes the compiler print some statistics about the time consumed by each
pass when it finishes.

@item -fmem-report
@opindex fmem-report
Makes the compiler print some statistics about permanent memory
allocation when it finishes.

@item -fprofile-arcs
@opindex fprofile-arcs
Add code so that program flow @dfn{arcs} are instrumented.  During
execution the program records how many times each branch and call is
executed and how many times it is taken or returns.  When the compiled
program exits it saves this data to a file called
@file{@var{auxname}.da} for each source file. The data may be used for
profile-directed optimizations (@option{-fbranch-probabilities}), or for
test coverage analysis (@option{-ftest-coverage}). Each object file's
@var{auxname} is generated from the name of the output file, if
explicitly specified and it is not the final executable, otherwise it is
the basename of the source file. In both cases any suffix is removed
(e.g.  @file{foo.da} for input file @file{dir/foo.c}, or
@file{dir/foo.da} for output file specified as @option{-o dir/foo.o}).

@itemize

@item
Compile the source files with @option{-fprofile-arcs} plus optimization
and code generation options. For test coverage analysis, use the
additional @option{-ftest-coverage} option. You do not need to profile
every source file in a program.

@item
Link your object files with @option{-lgcov} or @option{-fprofile-arcs}
(the latter implies the former).

@item
Run the program on a representative workload to generate the arc profile
information. This may be repeated any number of times. You can run
concurrent instances of your program, and provided that the file system
supports locking, the data files will be correctly updated. Also
@code{fork} calls are detected and correctly handled (double counting
will not happen).

@item
For profile-directed optimizations, compile the source files again with
the same optimization and code generation options plus
@option{-fbranch-probabilities} (@pxref{Optimize Options,,Options that
Control Optimization}).

@item
For test coverage analysis, use @command{gcov} to produce human readable
information from the @file{.bbg} and @file{.da} files. Refer to the
@command{gcov} documentation for further information.

@end itemize

With @option{-fprofile-arcs}, for each function of your program GCC
creates a program flow graph, then finds a spanning tree for the graph.
Only arcs that are not on the spanning tree have to be instrumented: the
compiler adds code to count the number of times that these arcs are
executed.  When an arc is the only exit or only entrance to a block, the
instrumentation code can be added to the block; otherwise, a new basic
block must be created to hold the instrumentation code.

@need 2000
@item -ftest-coverage
@opindex ftest-coverage
Produce a graph file that the @command{gcov} code-coverage utility
(@pxref{Gcov,, @command{gcov}---a Test Coverage Program}) can use to
show program coverage. Each source file's data file is called
@file{@var{auxname}.bbg}. Refer to the @option{-fprofile-arcs} option
above for a description of @var{auxname} and instructions on how to
generate test coverage data. Coverage data will match the source files
more closely, if you do not optimize.

@item -d@var{letters}
@opindex d
Says to make debugging dumps during compilation at times specified by
@var{letters}.  This is used for debugging the compiler.  The file names
for most of the dumps are made by appending a pass number and a word to
the @var{dumpname}. @var{dumpname} is generated from the name of the
output file, if explicitly specified and it is not an executable,
otherwise it is the basename of the source file. In both cases any
suffix is removed (e.g.  @file{foo.00.rtl} or @file{foo.01.sibling}).
Here are the possible letters for use in @var{letters}, and their
meanings:

@table @samp
@item A
@opindex dA
Annotate the assembler output with miscellaneous debugging information.
@item b
@opindex db
Dump after computing branch probabilities, to @file{@var{file}.14.bp}.
@item B
@opindex dB
Dump after block reordering, to @file{@var{file}.32.bbro}.
@item c
@opindex dc
Dump after instruction combination, to the file @file{@var{file}.19.combine}.
@item C
@opindex dC
Dump after the first if conversion, to the file @file{@var{file}.15.ce1}.
@item d
@opindex dd
Dump after delayed branch scheduling, to @file{@var{file}.34.dbr}.
@item D
@opindex dD
Dump all macro definitions, at the end of preprocessing, in addition to
normal output.
@item e
@opindex de
Dump after SSA optimizations, to @file{@var{file}.04.ssa} and
@file{@var{file}.07.ussa}.
@item E
@opindex dE
Dump after the second if conversion, to @file{@var{file}.29.ce3}.
@item f
@opindex df
Dump after life analysis, to @file{@var{file}.18.life}.
@item F
@opindex dF
Dump after purging @code{ADDRESSOF} codes, to @file{@var{file}.10.addressof}.
@item g
@opindex dg
Dump after global register allocation, to @file{@var{file}.24.greg}.
@item h
@opindex dh
Dump after finalization of EH handling code, to @file{@var{file}.02.eh}.
@item k
@opindex dk
Dump after reg-to-stack conversion, to @file{@var{file}.31.stack}.
@item o
@opindex do
Dump after post-reload optimizations, to @file{@var{file}.25.postreload}.
@item G
@opindex dG
Dump after GCSE, to @file{@var{file}.11.gcse}.
@item i
@opindex di
Dump after sibling call optimizations, to @file{@var{file}.01.sibling}.
@item j
@opindex dj
Dump after the first jump optimization, to @file{@var{file}.03.jump}.
@item k
@opindex dk
Dump after conversion from registers to stack, to @file{@var{file}.31.stack}.
@item l
@opindex dl
Dump after local register allocation, to @file{@var{file}.23.lreg}.
@item L
@opindex dL
Dump after loop optimization passes, to @file{@var{file}.12.loop} and
@file{@var{file}.18.loop2}.
@item M
@opindex dM
Dump after performing the machine dependent reorganization pass, to
@file{@var{file}.33.mach}.
@item n
@opindex dn
Dump after register renumbering, to @file{@var{file}.28.rnreg}.
@item N
@opindex dN
Dump after the register move pass, to @file{@var{file}.21.regmove}.
@item r
@opindex dr
Dump after RTL generation, to @file{@var{file}.00.rtl}.
@item R
@opindex dR
Dump after the second scheduling pass, to @file{@var{file}.30.sched2}.
@item s
@opindex ds
Dump after CSE (including the jump optimization that sometimes follows
CSE), to @file{@var{file}.09.cse}.
@item S
@opindex dS
Dump after the first scheduling pass, to @file{@var{file}.22.sched}.
@item t
@opindex dt
Dump after the second CSE pass (including the jump optimization that
sometimes follows CSE), to @file{@var{file}.17.cse2}.
@item u
@opindex du
Dump after null pointer elimination pass to @file{@var{file}.08.null}.
@item w
@opindex dw
Dump after the second flow pass, to @file{@var{file}.26.flow2}.
@item X
@opindex dX
Dump after SSA dead code elimination, to @file{@var{file}.06.ssadce}.
@item z
@opindex dz
Dump after the peephole pass, to @file{@var{file}.27.peephole2}.
@item a
@opindex da
Produce all the dumps listed above.
@item H
@opindex dH
Produce a core dump whenever an error occurs.
@item m
@opindex dm
Print statistics on memory usage, at the end of the run, to
standard error.
@item p
@opindex dp
Annotate the assembler output with a comment indicating which
pattern and alternative was used.  The length of each instruction is
also printed.
@item P
@opindex dP
Dump the RTL in the assembler output as a comment before each instruction.
Also turns on @option{-dp} annotation.
@item v
@opindex dv
For each of the other indicated dump files (except for
@file{@var{file}.00.rtl}), dump a representation of the control flow graph
suitable for viewing with VCG to @file{@var{file}.@var{pass}.vcg}.
@item x
@opindex dx
Just generate RTL for a function instead of compiling it.  Usually used
with @samp{r}.
@item y
@opindex dy
Dump debugging information during parsing, to standard error.
@end table

@item -fdump-unnumbered
@opindex fdump-unnumbered
When doing debugging dumps (see @option{-d} option above), suppress instruction
numbers and line number note output.  This makes it more feasible to
use diff on debugging dumps for compiler invocations with different
options, in particular with and without @option{-g}.

@item -fdump-translation-unit @r{(C and C++ only)}
@itemx -fdump-translation-unit-@var{options} @r{(C and C++ only)}
@opindex fdump-translation-unit
Dump a representation of the tree structure for the entire translation
unit to a file.  The file name is made by appending @file{.tu} to the
source file name.  If the @samp{-@var{options}} form is used, @var{options}
controls the details of the dump as described for the
@option{-fdump-tree} options.

@item -fdump-class-hierarchy @r{(C++ only)}
@itemx -fdump-class-hierarchy-@var{options} @r{(C++ only)}
@opindex fdump-class-hierarchy
Dump a representation of each class's hierarchy and virtual function
table layout to a file.  The file name is made by appending @file{.class}
to the source file name.  If the @samp{-@var{options}} form is used,
@var{options} controls the details of the dump as described for the
@option{-fdump-tree} options.

@item -fdump-tree-@var{switch} @r{(C++ only)}
@itemx -fdump-tree-@var{switch}-@var{options} @r{(C++ only)}
@opindex fdump-tree
Control the dumping at various stages of processing the intermediate
language tree to a file.  The file name is generated by appending a switch
specific suffix to the source file name.  If the @samp{-@var{options}}
form is used, @var{options} is a list of @samp{-} separated options that
control the details of the dump. Not all options are applicable to all
dumps, those which are not meaningful will be ignored. The following
options are available

@table @samp
@item address
Print the address of each node.  Usually this is not meaningful as it
changes according to the environment and source file. Its primary use
is for tying up a dump file with a debug environment.
@item slim
Inhibit dumping of members of a scope or body of a function merely
because that scope has been reached. Only dump such items when they
are directly reachable by some other path.
@item all
Turn on all options.
@end table

The following tree dumps are possible:
@table @samp
@item original
Dump before any tree based optimization, to @file{@var{file}.original}.
@item optimized
Dump after all tree based optimization, to @file{@var{file}.optimized}.
@item inlined
Dump after function inlining, to @file{@var{file}.inlined}.
@end table

@item -frandom-seed=@var{string}
@opindex frandom-string
This option provides a seed that GCC uses when it would otherwise use
random numbers.  At present, this is used to generate certain symbol names
that have to be different in every compiled file.

The @var{string} should be different for every file you compile.

@item -fsched-verbose=@var{n}
@opindex fsched-verbose
On targets that use instruction scheduling, this option controls the
amount of debugging output the scheduler prints.  This information is
written to standard error, unless @option{-dS} or @option{-dR} is
specified, in which case it is output to the usual dump
listing file, @file{.sched} or @file{.sched2} respectively.  However
for @var{n} greater than nine, the output is always printed to standard
error.

For @var{n} greater than zero, @option{-fsched-verbose} outputs the
same information as @option{-dRS}.  For @var{n} greater than one, it
also output basic block probabilities, detailed ready list information
and unit/insn info.  For @var{n} greater than two, it includes RTL
at abort point, control-flow and regions info.  And for @var{n} over
four, @option{-fsched-verbose} also includes dependence info.

@item -save-temps
@opindex save-temps
Store the usual ``temporary'' intermediate files permanently; place them
in the current directory and name them based on the source file.  Thus,
compiling @file{foo.c} with @samp{-c -save-temps} would produce files
@file{foo.i} and @file{foo.s}, as well as @file{foo.o}.  This creates a
preprocessed @file{foo.i} output file even though the compiler now
normally uses an integrated preprocessor.

@item -time
@opindex time
Report the CPU time taken by each subprocess in the compilation
sequence.  For C source files, this is the compiler proper and assembler
(plus the linker if linking is done).  The output looks like this:

@smallexample
# cc1 0.12 0.01
# as 0.00 0.01
@end smallexample

The first number on each line is the ``user time,'' that is time spent
executing the program itself.  The second number is ``system time,''
time spent executing operating system routines on behalf of the program.
Both numbers are in seconds.

@item -print-file-name=@var{library}
@opindex print-file-name
Print the full absolute name of the library file @var{library} that
would be used when linking---and don't do anything else.  With this
option, GCC does not compile or link anything; it just prints the
file name.

@item -print-multi-directory
@opindex print-multi-directory
Print the directory name corresponding to the multilib selected by any
other switches present in the command line.  This directory is supposed
to exist in @env{GCC_EXEC_PREFIX}.

@item -print-multi-lib
@opindex print-multi-lib
Print the mapping from multilib directory names to compiler switches
that enable them.  The directory name is separated from the switches by
@samp{;}, and each switch starts with an @samp{@@} instead of the
@samp{-}, without spaces between multiple switches.  This is supposed to
ease shell-processing.

@item -print-prog-name=@var{program}
@opindex print-prog-name
Like @option{-print-file-name}, but searches for a program such as @samp{cpp}.

@item -print-libgcc-file-name
@opindex print-libgcc-file-name
Same as @option{-print-file-name=libgcc.a}.

This is useful when you use @option{-nostdlib} or @option{-nodefaultlibs}
but you do want to link with @file{libgcc.a}.  You can do

@example
gcc -nostdlib @var{files}@dots{} `gcc -print-libgcc-file-name`
@end example

@item -print-search-dirs
@opindex print-search-dirs
Print the name of the configured installation directory and a list of
program and library directories gcc will search---and don't do anything else.

This is useful when gcc prints the error message
@samp{installation problem, cannot exec cpp0: No such file or directory}.
To resolve this you either need to put @file{cpp0} and the other compiler
components where gcc expects to find them, or you can set the environment
variable @env{GCC_EXEC_PREFIX} to the directory where you installed them.
Don't forget the trailing '/'.
@xref{Environment Variables}.

@item -dumpmachine
@opindex dumpmachine
Print the compiler's target machine (for example,
@samp{i686-pc-linux-gnu})---and don't do anything else.

@item -dumpversion
@opindex dumpversion
Print the compiler version (for example, @samp{3.0})---and don't do
anything else.

@item -dumpspecs
@opindex dumpspecs
Print the compiler's built-in specs---and don't do anything else.  (This
is used when GCC itself is being built.)  @xref{Spec Files}.

@item -feliminate-unused-debug-types
@opindex feliminate-unused-debug-types
Normally, when producing DWARF2 output, GCC will emit debugging
information for all types declared in a compilation
unit, regardless of whether or not they are actually used
in that compilation unit.  Sometimes this is useful, such as
if, in the debugger, you want to cast a value to a type that is
not actually used in your program (but is declared).  More often,
however, this results in a significant amount of wasted space.
With this option, GCC will avoid producing debug symbol output
for types that are nowhere used in the source file being compiled.
@end table

@node Optimize Options
@section Options That Control Optimization
@cindex optimize options
@cindex options, optimization

These options control various sorts of optimizations.

Without any optimization option, the compiler's goal is to reduce the
cost of compilation and to make debugging produce the expected
results.  Statements are independent: if you stop the program with a
breakpoint between statements, you can then assign a new value to any
variable or change the program counter to any other statement in the
function and get exactly the results you would expect from the source
code.

Turning on optimization flags makes the compiler attempt to improve
the performance and/or code size at the expense of compilation time
and possibly the ability to debug the program.

Not all optimizations are controlled directly by a flag.  Only
optimizations that have a flag are listed.

@table @gcctabopt
@item -O
@itemx -O1
@opindex O
@opindex O1
Optimize.  Optimizing compilation takes somewhat more time, and a lot
more memory for a large function.

With @option{-O}, the compiler tries to reduce code size and execution
time, without performing any optimizations that take a great deal of
compilation time.

@option{-O} turns on the following optimization flags: 
@gccoptlist{-fdefer-pop @gol
-fmerge-constants @gol
-fthread-jumps @gol
-floop-optimize @gol
-fcrossjumping @gol
-fif-conversion @gol
-fif-conversion2 @gol
-fdelayed-branch @gol
-fguess-branch-probability @gol
-fcprop-registers}

@option{-O} also turns on @option{-fomit-frame-pointer} on machines
where doing so does not interfere with debugging.

@item -O2
@opindex O2
Optimize even more.  GCC performs nearly all supported optimizations
that do not involve a space-speed tradeoff.  The compiler does not
perform loop unrolling or function inlining when you specify @option{-O2}.
As compared to @option{-O}, this option increases both compilation time
and the performance of the generated code.

@option{-O2} turns on all optimization flags specified by @option{-O}.  It
also turns on the following optimization flags:
@gccoptlist{-fforce-mem @gol
-foptimize-sibling-calls @gol
-fstrength-reduce @gol
-fcse-follow-jumps  -fcse-skip-blocks @gol
-frerun-cse-after-loop  -frerun-loop-opt @gol
-fgcse   -fgcse-lm   -fgcse-sm @gol
-fdelete-null-pointer-checks @gol
-fexpensive-optimizations @gol
-fregmove @gol
-fschedule-insns  -fschedule-insns2 @gol
-fsched-interblock  -fsched-spec @gol
-fcaller-saves @gol
-fpeephole2 @gol
-freorder-blocks  -freorder-functions @gol
-fstrict-aliasing @gol
-falign-functions  -falign-jumps @gol
-falign-loops  -falign-labels}

Please note the warning under @option{-fgcse} about
invoking @option{-O2} on programs that use computed gotos.

@item -O3
@opindex O3
Optimize yet more.  @option{-O3} turns on all optimizations specified by
@option{-O2} and also turns on the @option{-finline-functions},
@option{-funit-at-a-time} and @option{-frename-registers} options.

@item -O0
@opindex O0
Do not optimize.  This is the default.

@item -Os
@opindex Os
Optimize for size.  @option{-Os} enables all @option{-O2} optimizations that
do not typically increase code size.  It also performs further
optimizations designed to reduce code size.

@option{-Os} disables the following optimization flags:
@gccoptlist{-falign-functions  -falign-jumps  -falign-loops @gol
-falign-labels  -freorder-blocks  -fprefetch-loop-arrays}

If you use multiple @option{-O} options, with or without level numbers,
the last such option is the one that is effective.
@end table

Options of the form @option{-f@var{flag}} specify machine-independent
flags.  Most flags have both positive and negative forms; the negative
form of @option{-ffoo} would be @option{-fno-foo}.  In the table
below, only one of the forms is listed---the one you typically will
use.  You can figure out the other form by either removing @samp{no-}
or adding it.

The following options control specific optimizations.  They are either
activated by @option{-O} options or are related to ones that are.  You
can use the following flags in the rare cases when ``fine-tuning'' of
optimizations to be performed is desired.

@table @gcctabopt
@item -fno-default-inline
@opindex fno-default-inline
Do not make member functions inline by default merely because they are
defined inside the class scope (C++ only).  Otherwise, when you specify
@w{@option{-O}}, member functions defined inside class scope are compiled
inline by default; i.e., you don't need to add @samp{inline} in front of
the member function name.

@item -fno-defer-pop
@opindex fno-defer-pop
Always pop the arguments to each function call as soon as that function
returns.  For machines which must pop arguments after a function call,
the compiler normally lets arguments accumulate on the stack for several
function calls and pops them all at once.

Disabled at levels @option{-O}, @option{-O2}, @option{-O3}, @option{-Os}.

@item -fforce-mem
@opindex fforce-mem
Force memory operands to be copied into registers before doing
arithmetic on them.  This produces better code by making all memory
references potential common subexpressions.  When they are not common
subexpressions, instruction combination should eliminate the separate
register-load.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fforce-addr
@opindex fforce-addr
Force memory address constants to be copied into registers before
doing arithmetic on them.  This may produce better code just as
@option{-fforce-mem} may.

@item -fomit-frame-pointer
@opindex fomit-frame-pointer
Don't keep the frame pointer in a register for functions that
don't need one.  This avoids the instructions to save, set up and
restore frame pointers; it also makes an extra register available
in many functions.  @strong{It also makes debugging impossible on
some machines.}

On some machines, such as the VAX, this flag has no effect, because
the standard calling sequence automatically handles the frame pointer
and nothing is saved by pretending it doesn't exist.  The
machine-description macro @code{FRAME_POINTER_REQUIRED} controls
whether a target machine supports this flag.  @xref{Registers,,Register
Usage, gccint, GNU Compiler Collection (GCC) Internals}.

Enabled at levels @option{-O}, @option{-O2}, @option{-O3}, @option{-Os}.

@item -foptimize-sibling-calls
@opindex foptimize-sibling-calls
Optimize sibling and tail recursive calls.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fno-inline
@opindex fno-inline
Don't pay attention to the @code{inline} keyword.  Normally this option
is used to keep the compiler from expanding any functions inline.
Note that if you are not optimizing, no functions can be expanded inline.

@item -finline-functions
@opindex finline-functions
Integrate all simple functions into their callers.  The compiler
heuristically decides which functions are simple enough to be worth
integrating in this way.

If all calls to a given function are integrated, and the function is
declared @code{static}, then the function is normally not output as
assembler code in its own right.

Enabled at level @option{-O3}.

@item -finline-limit=@var{n}
@opindex finline-limit
By default, gcc limits the size of functions that can be inlined.  This flag
allows the control of this limit for functions that are explicitly marked as
inline (i.e., marked with the inline keyword or defined within the class
definition in c++).  @var{n} is the size of functions that can be inlined in
number of pseudo instructions (not counting parameter handling).  The default
value of @var{n} is 600.
Increasing this value can result in more inlined code at
the cost of compilation time and memory consumption.  Decreasing usually makes
the compilation faster and less code will be inlined (which presumably
means slower programs).  This option is particularly useful for programs that
use inlining heavily such as those based on recursive templates with C++.

Inlining is actually controlled by a number of parameters, which may be
specified individually by using @option{--param @var{name}=@var{value}}.
The @option{-finline-limit=@var{n}} option sets some of these parameters 
as follows:

@table @gcctabopt
 @item max-inline-insns
  is set to @var{n}.
 @item max-inline-insns-single
  is set to @var{n}/2.
 @item max-inline-insns-auto
  is set to @var{n}/2.
 @item min-inline-insns
  is set to 130 or @var{n}/4, whichever is smaller.
 @item max-inline-insns-rtl
  is set to @var{n}.
@end table

Using @option{-finline-limit=600} thus results in the default settings
for these parameters.  See below for a documentation of the individual
parameters controlling inlining.

@emph{Note:} pseudo instruction represents, in this particular context, an
abstract measurement of function's size.  In no way, it represents a count
of assembly instructions and as such its exact meaning might change from one
release to an another.

@item -fkeep-inline-functions
@opindex fkeep-inline-functions
Even if all calls to a given function are integrated, and the function
is declared @code{static}, nevertheless output a separate run-time
callable version of the function.  This switch does not affect
@code{extern inline} functions.

@item -fkeep-static-consts
@opindex fkeep-static-consts
Emit variables declared @code{static const} when optimization isn't turned
on, even if the variables aren't referenced.

GCC enables this option by default.  If you want to force the compiler to
check if the variable was referenced, regardless of whether or not
optimization is turned on, use the @option{-fno-keep-static-consts} option.

@item -fmerge-constants
Attempt to merge identical constants (string constants and floating point
constants) across compilation units.

This option is the default for optimized compilation if the assembler and
linker support it.  Use @option{-fno-merge-constants} to inhibit this
behavior.

Enabled at levels @option{-O}, @option{-O2}, @option{-O3}, @option{-Os}.

@item -fmerge-all-constants
Attempt to merge identical constants and identical variables.

This option implies @option{-fmerge-constants}.  In addition to
@option{-fmerge-constants} this considers e.g. even constant initialized
arrays or initialized constant variables with integral or floating point
types.  Languages like C or C++ require each non-automatic variable to
have distinct location, so using this option will result in non-conforming
behavior.

@item -fnew-ra
@opindex fnew-ra
Use a graph coloring register allocator.  Currently this option is meant
for testing, so we are interested to hear about miscompilations with
@option{-fnew-ra}.

@item -fno-branch-count-reg
@opindex fno-branch-count-reg
Do not use ``decrement and branch'' instructions on a count register,
but instead generate a sequence of instructions that decrement a
register, compare it against zero, then branch based upon the result.
This option is only meaningful on architectures that support such
instructions, which include x86, PowerPC, IA-64 and S/390.

The default is @option{-fbranch-count-reg}, enabled when
@option{-fstrength-reduce} is enabled.

@item -fno-function-cse
@opindex fno-function-cse
Do not put function addresses in registers; make each instruction that
calls a constant function contain the function's address explicitly.

This option results in less efficient code, but some strange hacks
that alter the assembler output may be confused by the optimizations
performed when this option is not used.

The default is @option{-ffunction-cse}

@item -fno-zero-initialized-in-bss
@opindex fno-zero-initialized-in-bss
If the target supports a BSS section, GCC by default puts variables that
are initialized to zero into BSS@.  This can save space in the resulting
code.

This option turns off this behavior because some programs explicitly
rely on variables going to the data section.  E.g., so that the
resulting executable can find the beginning of that section and/or make
assumptions based on that.

The default is @option{-fzero-initialized-in-bss}.

@item -fstrength-reduce
@opindex fstrength-reduce
Perform the optimizations of loop strength reduction and
elimination of iteration variables.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fthread-jumps
@opindex fthread-jumps
Perform optimizations where we check to see if a jump branches to a
location where another comparison subsumed by the first is found.  If
so, the first branch is redirected to either the destination of the
second branch or a point immediately following it, depending on whether
the condition is known to be true or false.

Enabled at levels @option{-O}, @option{-O2}, @option{-O3}, @option{-Os}.

@item -fcse-follow-jumps
@opindex fcse-follow-jumps
In common subexpression elimination, scan through jump instructions
when the target of the jump is not reached by any other path.  For
example, when CSE encounters an @code{if} statement with an
@code{else} clause, CSE will follow the jump when the condition
tested is false.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fcse-skip-blocks
@opindex fcse-skip-blocks
This is similar to @option{-fcse-follow-jumps}, but causes CSE to
follow jumps which conditionally skip over blocks.  When CSE
encounters a simple @code{if} statement with no else clause,
@option{-fcse-skip-blocks} causes CSE to follow the jump around the
body of the @code{if}.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -frerun-cse-after-loop
@opindex frerun-cse-after-loop
Re-run common subexpression elimination after loop optimizations has been
performed.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -frerun-loop-opt
@opindex frerun-loop-opt
Run the loop optimizer twice.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fgcse
@opindex fgcse
Perform a global common subexpression elimination pass.
This pass also performs global constant and copy propagation.

@emph{Note:} When compiling a program using computed gotos, a GCC
extension, you may get better runtime performance if you disable
the global common subexpression elimination pass by adding
@option{-fno-gcse} to the command line.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fgcse-lm
@opindex fgcse-lm
When @option{-fgcse-lm} is enabled, global common subexpression elimination will
attempt to move loads which are only killed by stores into themselves.  This
allows a loop containing a load/store sequence to be changed to a load outside
the loop, and a copy/store within the loop.

Enabled by default when gcse is enabled.

@item -fgcse-sm
@opindex fgcse-sm
When @option{-fgcse-sm} is enabled, A store motion pass is run after global common
subexpression elimination.  This pass will attempt to move stores out of loops.
When used in conjunction with @option{-fgcse-lm}, loops containing a load/store sequence
can be changed to a load before the loop and a store after the loop.

Enabled by default when gcse is enabled.

@item -floop-optimize
@opindex floop-optimize
Perform loop optimizations: move constant expressions out of loops, simplify
exit test conditions and optionally do strength-reduction and loop unrolling as
well.

Enabled at levels @option{-O}, @option{-O2}, @option{-O3}, @option{-Os}.

@item -fcrossjumping
@opindex crossjumping
Perform cross-jumping transformation. This transformation unifies equivalent code and save code size. The
resulting code may or may not perform better than without cross-jumping.

Enabled at levels @option{-O}, @option{-O2}, @option{-O3}, @option{-Os}.

@item -fif-conversion
@opindex if-conversion
Attempt to transform conditional jumps into branch-less equivalents.  This
include use of conditional moves, min, max, set flags and abs instructions, and
some tricks doable by standard arithmetics.  The use of conditional execution
on chips where it is available is controlled by @code{if-conversion2}.

Enabled at levels @option{-O}, @option{-O2}, @option{-O3}, @option{-Os}.

@item -fif-conversion2
@opindex if-conversion2
Use conditional execution (where available) to transform conditional jumps into
branch-less equivalents.

Enabled at levels @option{-O}, @option{-O2}, @option{-O3}, @option{-Os}.

@item -fdelete-null-pointer-checks
@opindex fdelete-null-pointer-checks
Use global dataflow analysis to identify and eliminate useless checks
for null pointers.  The compiler assumes that dereferencing a null
pointer would have halted the program.  If a pointer is checked after
it has already been dereferenced, it cannot be null.

In some environments, this assumption is not true, and programs can
safely dereference null pointers.  Use
@option{-fno-delete-null-pointer-checks} to disable this optimization
for programs which depend on that behavior.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fexpensive-optimizations
@opindex fexpensive-optimizations
Perform a number of minor optimizations that are relatively expensive.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -foptimize-register-move
@itemx -fregmove
@opindex foptimize-register-move
@opindex fregmove
Attempt to reassign register numbers in move instructions and as
operands of other simple instructions in order to maximize the amount of
register tying.  This is especially helpful on machines with two-operand
instructions.

Note @option{-fregmove} and @option{-foptimize-register-move} are the same
optimization.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fdelayed-branch
@opindex fdelayed-branch
If supported for the target machine, attempt to reorder instructions
to exploit instruction slots available after delayed branch
instructions.

Enabled at levels @option{-O}, @option{-O2}, @option{-O3}, @option{-Os}.

@item -fschedule-insns
@opindex fschedule-insns
If supported for the target machine, attempt to reorder instructions to
eliminate execution stalls due to required data being unavailable.  This
helps machines that have slow floating point or memory load instructions
by allowing other instructions to be issued until the result of the load
or floating point instruction is required.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fschedule-insns2
@opindex fschedule-insns2
Similar to @option{-fschedule-insns}, but requests an additional pass of
instruction scheduling after register allocation has been done.  This is
especially useful on machines with a relatively small number of
registers and where memory load instructions take more than one cycle.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fno-sched-interblock
@opindex fno-sched-interblock
Don't schedule instructions across basic blocks.  This is normally
enabled by default when scheduling before register allocation, i.e.@:
with @option{-fschedule-insns} or at @option{-O2} or higher.

@item -fno-sched-spec
@opindex fno-sched-spec
Don't allow speculative motion of non-load instructions.  This is normally
enabled by default when scheduling before register allocation, i.e.@:
with @option{-fschedule-insns} or at @option{-O2} or higher.

@item -fsched-spec-load
@opindex fsched-spec-load
Allow speculative motion of some load instructions.  This only makes
sense when scheduling before register allocation, i.e.@: with
@option{-fschedule-insns} or at @option{-O2} or higher.

@item -fsched-spec-load-dangerous
@opindex fsched-spec-load-dangerous
Allow speculative motion of more load instructions.  This only makes
sense when scheduling before register allocation, i.e.@: with
@option{-fschedule-insns} or at @option{-O2} or higher.

@item -fsched2-use-superblocks
@opindex fsched2-use-superblocks
When schedulilng after register allocation, do use superblock scheduling
algorithm.  Superblock scheduling allows motion across basic block boundaries
resulting on faster schedules.  This option is experimental, as not all machine
descriptions used by GCC model the CPU closely enough to avoid unreliable
results from the algorithm. 

This only makes sense when scheduling after register allocation, i.e.@: with
@option{-fschedule-insns2} or at @option{-O2} or higher.

@item -fsched2-use-traces
@opindex fsched2-use-traces
Use @option{-fsched2-use-superblocks} algorithm when scheduling after register
allocation and additionally perform code duplication in order to increase the
size of superblocks using tracer pass.  See @option{-ftracer} for details on
trace formation.

This mode should produce faster but significantly longer programs.  Also
without @code{-fbranch-probabilities} the traces constructed may not match the
reality and hurt the performance.  This only makes
sense when scheduling after register allocation, i.e.@: with
@option{-fschedule-insns2} or at @option{-O2} or higher.

@item -fcaller-saves
@opindex fcaller-saves
Enable values to be allocated in registers that will be clobbered by
function calls, by emitting extra instructions to save and restore the
registers around such calls.  Such allocation is done only when it
seems to result in better code than would otherwise be produced.

This option is always enabled by default on certain machines, usually
those which have no call-preserved registers to use instead.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fmove-all-movables
@opindex fmove-all-movables
Forces all invariant computations in loops to be moved
outside the loop.

@item -freduce-all-givs
@opindex freduce-all-givs
Forces all general-induction variables in loops to be
strength-reduced.

@emph{Note:} When compiling programs written in Fortran,
@option{-fmove-all-movables} and @option{-freduce-all-givs} are enabled
by default when you use the optimizer.

These options may generate better or worse code; results are highly
dependent on the structure of loops within the source code.

These two options are intended to be removed someday, once
they have helped determine the efficacy of various
approaches to improving loop optimizations.

Please let us (@w{@email{gcc@@gcc.gnu.org}} and @w{@email{fortran@@gnu.org}})
know how use of these options affects
the performance of your production code.
We're very interested in code that runs @emph{slower}
when these options are @emph{enabled}.

@item -fno-peephole
@itemx -fno-peephole2
@opindex fno-peephole
@opindex fno-peephole2
Disable any machine-specific peephole optimizations.  The difference
between @option{-fno-peephole} and @option{-fno-peephole2} is in how they
are implemented in the compiler; some targets use one, some use the
other, a few use both.

@option{-fpeephole} is enabled by default.
@option{-fpeephole2} enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fno-guess-branch-probability
@opindex fno-guess-branch-probability
Do not guess branch probabilities using a randomized model.

Sometimes gcc will opt to use a randomized model to guess branch
probabilities, when none are available from either profiling feedback
(@option{-fprofile-arcs}) or @samp{__builtin_expect}.  This means that
different runs of the compiler on the same program may produce different
object code.

In a hard real-time system, people don't want different runs of the
compiler to produce code that has different behavior; minimizing
non-determinism is of paramount import.  This switch allows users to
reduce non-determinism, possibly at the expense of inferior
optimization.

The default is @option{-fguess-branch-probability} at levels
@option{-O}, @option{-O2}, @option{-O3}, @option{-Os}.

@item -freorder-blocks
@opindex freorder-blocks
Reorder basic blocks in the compiled function in order to reduce number of
taken branches and improve code locality.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -freorder-functions
@opindex freorder-functions
Reorder basic blocks in the compiled function in order to reduce number of
taken branches and improve code locality. This is implemented by using special
subsections @code{text.hot} for most frequently executed functions and
@code{text.unlikely} for unlikely executed functions.  Reordering is done by
the linker so object file format must support named sections and linker must
place them in a reasonable way.

Also profile feedback must be available in to make this option effective.  See
@option{-fprofile-arcs} for details.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -fstrict-aliasing
@opindex fstrict-aliasing
Allows the compiler to assume the strictest aliasing rules applicable to
the language being compiled.  For C (and C++), this activates
optimizations based on the type of expressions.  In particular, an
object of one type is assumed never to reside at the same address as an
object of a different type, unless the types are almost the same.  For
example, an @code{unsigned int} can alias an @code{int}, but not a
@code{void*} or a @code{double}.  A character type may alias any other
type.

Pay special attention to code like this:
@example
union a_union @{
  int i;
  double d;
@};

int f() @{
  a_union t;
  t.d = 3.0;
  return t.i;
@}
@end example
The practice of reading from a different union member than the one most
recently written to (called ``type-punning'') is common.  Even with
@option{-fstrict-aliasing}, type-punning is allowed, provided the memory
is accessed through the union type.  So, the code above will work as
expected.  However, this code might not:
@example
int f() @{
  a_union t;
  int* ip;
  t.d = 3.0;
  ip = &t.i;
  return *ip;
@}
@end example

Every language that wishes to perform language-specific alias analysis
should define a function that computes, given an @code{tree}
node, an alias set for the node.  Nodes in different alias sets are not
allowed to alias.  For an example, see the C front-end function
@code{c_get_alias_set}.

Enabled at levels @option{-O2}, @option{-O3}, @option{-Os}.

@item -falign-functions
@itemx -falign-functions=@var{n}
@opindex falign-functions
Align the start of functions to the next power-of-two greater than
@var{n}, skipping up to @var{n} bytes.  For instance,
@option{-falign-functions=32} aligns functions to the next 32-byte
boundary, but @option{-falign-functions=24} would align to the next
32-byte boundary only if this can be done by skipping 23 bytes or less.

@option{-fno-align-functions} and @option{-falign-functions=1} are
equivalent and mean that functions will not be aligned.

Some assemblers only support this flag when @var{n} is a power of two;
in that case, it is rounded up.

If @var{n} is not specified, use a machine-dependent default.

Enabled at levels @option{-O2}, @option{-O3}.

@item -falign-labels
@itemx -falign-labels=@var{n}
@opindex falign-labels
Align all branch targets to a power-of-two boundary, skipping up to
@var{n} bytes like @option{-falign-functions}.  This option can easily
make code slower, because it must insert dummy operations for when the
branch target is reached in the usual flow of the code.

If @option{-falign-loops} or @option{-falign-jumps} are applicable and
are greater than this value, then their values are used instead.

If @var{n} is not specified, use a machine-dependent default which is
very likely to be @samp{1}, meaning no alignment.

Enabled at levels @option{-O2}, @option{-O3}.

@item -falign-loops
@itemx -falign-loops=@var{n}
@opindex falign-loops
Align loops to a power-of-two boundary, skipping up to @var{n} bytes
like @option{-falign-functions}.  The hope is that the loop will be
executed many times, which will make up for any execution of the dummy
operations.

If @var{n} is not specified, use a machine-dependent default.

Enabled at levels @option{-O2}, @option{-O3}.

@item -falign-jumps
@itemx -falign-jumps=@var{n}
@opindex falign-jumps
Align branch targets to a power-of-two boundary, for branch targets
where the targets can only be reached by jumping, skipping up to @var{n}
bytes like @option{-falign-functions}.  In this case, no dummy operations
need be executed.

If @var{n} is not specified, use a machine-dependent default.

Enabled at levels @option{-O2}, @option{-O3}.

@item -frename-registers
@opindex frename-registers
Attempt to avoid false dependencies in scheduled code by making use
of registers left over after register allocation.  This optimization
will most benefit processors with lots of registers.  It can, however,
make debugging impossible, since variables will no longer stay in
a ``home register''.

Enabled at levels @option{-O3}.

@item -fno-cprop-registers
@opindex fno-cprop-registers
After register allocation and post-register allocation instruction splitting,
we perform a copy-propagation pass to try to reduce scheduling dependencies
and occasionally eliminate the copy.

Disabled at levels @option{-O}, @option{-O2}, @option{-O3}, @option{-Os}.

@end table

The following options control compiler behavior regarding floating
point arithmetic.  These options trade off between speed and
correctness.  All must be specifically enabled.

@table @gcctabopt
@item -ffloat-store
@opindex ffloat-store
Do not store floating point variables in registers, and inhibit other
options that might change whether a floating point value is taken from a
register or memory.

@cindex floating point precision
This option prevents undesirable excess precision on machines such as
the 68000 where the floating registers (of the 68881) keep more
precision than a @code{double} is supposed to have.  Similarly for the
x86 architecture.  For most programs, the excess precision does only
good, but a few programs rely on the precise definition of IEEE floating
point.  Use @option{-ffloat-store} for such programs, after modifying
them to store all pertinent intermediate computations into variables.

@item -ffast-math
@opindex ffast-math
Sets @option{-fno-math-errno}, @option{-funsafe-math-optimizations}, @*
@option{-fno-trapping-math}, @option{-ffinite-math-only} and @*
@option{-fno-signaling-nans}.

This option causes the preprocessor macro @code{__FAST_MATH__} to be defined.

This option should never be turned on by any @option{-O} option since
it can result in incorrect output for programs which depend on
an exact implementation of IEEE or ISO rules/specifications for
math functions.

@item -fno-math-errno
@opindex fno-math-errno
Do not set ERRNO after calling math functions that are executed
with a single instruction, e.g., sqrt.  A program that relies on
IEEE exceptions for math error handling may want to use this flag
for speed while maintaining IEEE arithmetic compatibility.

This option should never be turned on by any @option{-O} option since
it can result in incorrect output for programs which depend on
an exact implementation of IEEE or ISO rules/specifications for
math functions.

The default is @option{-fmath-errno}.

@item -funsafe-math-optimizations
@opindex funsafe-math-optimizations
Allow optimizations for floating-point arithmetic that (a) assume
that arguments and results are valid and (b) may violate IEEE or
ANSI standards.  When used at link-time, it may include libraries
or startup files that change the default FPU control word or other
similar optimizations.

This option should never be turned on by any @option{-O} option since
it can result in incorrect output for programs which depend on
an exact implementation of IEEE or ISO rules/specifications for
math functions.

The default is @option{-fno-unsafe-math-optimizations}.

@item -ffinite-math-only
@opindex ffinite-math-only
Allow optimizations for floating-point arithmetic that assume
that arguments and results are not NaNs or +-Infs.

This option should never be turned on by any @option{-O} option since
it can result in incorrect output for programs which depend on
an exact implementation of IEEE or ISO rules/specifications.

The default is @option{-fno-finite-math-only}.

@item -fno-trapping-math
@opindex fno-trapping-math
Compile code assuming that floating-point operations cannot generate
user-visible traps.  These traps include division by zero, overflow,
underflow, inexact result and invalid operation.  This option implies
@option{-fno-signaling-nans}.  Setting this option may allow faster
code if one relies on ``non-stop'' IEEE arithmetic, for example.

This option should never be turned on by any @option{-O} option since
it can result in incorrect output for programs which depend on
an exact implementation of IEEE or ISO rules/specifications for
math functions.

The default is @option{-ftrapping-math}.

@item -fsignaling-nans
@opindex fsignaling-nans
Compile code assuming that IEEE signaling NaNs may generate user-visible
traps during floating-point operations.  Setting this option disables
optimizations that may change the number of exceptions visible with
signaling NaNs.  This option implies @option{-ftrapping-math}.

This option causes the preprocessor macro @code{__SUPPORT_SNAN__} to
be defined.

The default is @option{-fno-signaling-nans}.

This option is experimental and does not currently guarantee to
disable all GCC optimizations that affect signaling NaN behavior.

@item -fsingle-precision-constant
@opindex fsingle-precision-constant
Treat floating point constant as single precision constant instead of
implicitly converting it to double precision constant.


@end table

The following options control optimizations that may improve
performance, but are not enabled by any @option{-O} options.  This
section includes experimental options that may produce broken code.

@table @gcctabopt
@item -fbranch-probabilities
@opindex fbranch-probabilities
After running a program compiled with @option{-fprofile-arcs}
(@pxref{Debugging Options,, Options for Debugging Your Program or
@command{gcc}}), you can compile it a second time using
@option{-fbranch-probabilities}, to improve optimizations based on
the number of times each branch was taken.  When the program
compiled with @option{-fprofile-arcs} exits it saves arc execution
counts to a file called @file{@var{sourcename}.da} for each source
file  The information in this data file is very dependent on the
structure of the generated code, so you must use the same source code
and the same optimization options for both compilations.

With @option{-fbranch-probabilities}, GCC puts a 
@samp{REG_BR_PROB} note on each @samp{JUMP_INSN} and @samp{CALL_INSN}.
These can be used to improve optimization.  Currently, they are only
used in one place: in @file{reorg.c}, instead of guessing which path a
branch is mostly to take, the @samp{REG_BR_PROB} values are used to
exactly determine which path is taken more often.

@item -fnew-ra
@opindex fnew-ra
Use a graph coloring register allocator.  Currently this option is meant
for testing, so we are interested to hear about miscompilations with
@option{-fnew-ra}.

@item -ftracer
@opindex ftracer
Perform tail duplication to enlarge superblock size. This transformation
simplifies the control flow of the function allowing other optimizations to do
better job.

@item -funit-at-a-time
@opindex funit-at-a-time
Parse the whole compilation unit before starting to produce code.  This allows some
extra optimizations to take place but consumes more memory.

@item -funroll-loops
@opindex funroll-loops
Unroll loops whose number of iterations can be determined at compile time or
upon entry to the loop.  @option{-funroll-loops} implies
@option{-frerun-cse-after-loop}.  It also turns on complete loop peeling
(i.e. complete removal of loops with small constant number of iterations).
This option makes code larger, and may or may not make it run faster.

@item -funroll-all-loops
@opindex funroll-all-loops
Unroll all loops, even if their number of iterations is uncertain when
the loop is entered.  This usually makes programs run more slowly.
@option{-funroll-all-loops} implies the same options as
@option{-funroll-loops}.

@item -fpeel-loops
@opindex fpeel-loops
Peels the loops for that there is enough information that they do not
roll much (from profile feedback).  It also turns on complete loop peeling
(i.e. complete removal of loops with small constant number of iterations).

@item -funswitch-loops
@opindex funswitch-loops
Move branches with loop invariant conditions out of the loop, with duplicates
of the loop on both branches (modified according to result of the condition).

@item -fold-unroll-loops
@opindex fold-unroll-loops
Unroll loops whose number of iterations can be determined at compile
time or upon entry to the loop, using the old loop unroller whose loop
recognition is based on notes from frontend.  @option{-fold-unroll-loops} implies
both @option{-fstrength-reduce} and @option{-frerun-cse-after-loop}.  This
option makes code larger, and may or may not make it run faster.

@item -fold-unroll-all-loops
@opindex fold-unroll-all-loops
Unroll all loops, even if their number of iterations is uncertain when
the loop is entered. This is done using the old loop unroller whose loop
recognition is based on notes from frontend.  This usually makes programs run more slowly.
@option{-fold-unroll-all-loops} implies the same options as
@option{-fold-unroll-loops}.
 
@item -funswitch-loops
@opindex funswitch-loops
Move branches with loop invariant conditions out of the loop, with duplicates
of the loop on both branches (modified according to result of the condition).

@item -funswitch-loops
@opindex funswitch-loops
Move branches with loop invariant conditions out of the loop, with duplicates
of the loop on both branches (modified according to result of the condition).

@item -fprefetch-loop-arrays
@opindex fprefetch-loop-arrays
If supported by the target machine, generate instructions to prefetch
memory to improve the performance of loops that access large arrays.

Disabled at level @option{-Os}.

@item -ffunction-sections
@itemx -fdata-sections
@opindex ffunction-sections
@opindex fdata-sections
Place each function or data item into its own section in the output
file if the target supports arbitrary sections.  The name of the
function or the name of the data item determines the section's name
in the output file.

Use these options on systems where the linker can perform optimizations
to improve locality of reference in the instruction space.  Most systems
using the ELF object format and SPARC processors running Solaris 2 have
linkers with such optimizations.  AIX may have these optimizations in
the future.

Only use these options when there are significant benefits from doing
so.  When you specify these options, the assembler and linker will
create larger object and executable files and will also be slower.
You will not be able to use @code{gprof} on all systems if you
specify this option and you may have problems with debugging if
you specify both this option and @option{-g}.

@item -fssa
@opindex fssa
Perform optimizations in static single assignment form.  Each function's
flow graph is translated into SSA form, optimizations are performed, and
the flow graph is translated back from SSA form.  Users should not
specify this option, since it is not yet ready for production use.

@item -fssa-ccp
@opindex fssa-ccp
Perform Sparse Conditional Constant Propagation in SSA form.  Requires
@option{-fssa}.  Like @option{-fssa}, this is an experimental feature.

@item -fssa-dce
@opindex fssa-dce
Perform aggressive dead-code elimination in SSA form.  Requires @option{-fssa}.
Like @option{-fssa}, this is an experimental feature.




@item --param @var{name}=@var{value}
@opindex param
In some places, GCC uses various constants to control the amount of
optimization that is done.  For example, GCC will not inline functions
that contain more that a certain number of instructions.  You can
control some of these constants on the command-line using the
@option{--param} option.

In each case, the @var{value} is an integer.  The allowable choices for
@var{name} are given in the following table:

@table @gcctabopt
@item max-crossjump-edges
The maximum number of incoming edges to consider for crossjumping.
The algorithm used by @option{-fcrossjumping} is @math{O(N^2)} in
the number of edges incoming to each block.  Increasing values mean
more aggressive optimization, making the compile time increase with
probably small improvement in executable size.

@item max-delay-slot-insn-search
The maximum number of instructions to consider when looking for an
instruction to fill a delay slot.  If more than this arbitrary number of
instructions is searched, the time savings from filling the delay slot
will be minimal so stop searching.  Increasing values mean more
aggressive optimization, making the compile time increase with probably
small improvement in executable run time.

@item max-delay-slot-live-search
When trying to fill delay slots, the maximum number of instructions to
consider when searching for a block with valid live register
information.  Increasing this arbitrarily chosen value means more
aggressive optimization, increasing the compile time.  This parameter
should be removed when the delay slot code is rewritten to maintain the
control-flow graph.

@item max-gcse-memory
The approximate maximum amount of memory that will be allocated in
order to perform the global common subexpression elimination
optimization.  If more memory than specified is required, the
optimization will not be done.

@item max-gcse-passes
The maximum number of passes of GCSE to run.

@item max-pending-list-length
The maximum number of pending dependencies scheduling will allow
before flushing the current state and starting over.  Large functions
with few branches or calls can create excessively large lists which
needlessly consume memory and resources.

@item max-inline-insns-single
Several parameters control the tree inliner used in gcc.
This number sets the maximum number of instructions (counted in gcc's
internal representation) in a single function that the tree inliner 
will consider for inlining.  This only affects functions declared
inline and methods implemented in a class declaration (C++).
The default value is 300.

@item max-inline-insns-auto
When you use @option{-finline-functions} (included in @option{-O3}),
a lot of functions that would otherwise not be considered for inlining
by the compiler will be investigated.  To those functions, a different
(more restrictive) limit compared to functions declared inline can
be applied.
The default value is 300.

@item max-inline-insns
The tree inliner does decrease the allowable size for single functions 
to be inlined after we already inlined the number of instructions
given here by repeated inlining.  This number should be a factor of 
two or more larger than the single function limit.
Higher numbers result in better runtime performance, but incur higher
compile-time resource (CPU time, memory) requirements and result in
larger binaries.  Very high values are not advisable, as too large
binaries may adversely affect runtime performance.
The default value is 600.

@item max-inline-slope
After exceeding the maximum number of inlined instructions by repeated
inlining, a linear function is used to decrease the allowable size
for single functions.  The slope of that function is the negative
reciprocal of the number specified here.
The default value is 32.

@item min-inline-insns
The repeated inlining is throttled more and more by the linear function
after exceeding the limit.  To avoid too much throttling, a minimum for
this function is specified here to allow repeated inlining for very small
functions even when a lot of repeated inlining already has been done.
The default value is 130.

@item max-inline-insns-rtl
For languages that use the RTL inliner (this happens at a later stage
than tree inlining), you can set the maximum allowable size (counted 
in RTL instructions) for the RTL inliner with this parameter.
The default value is 600.


@item max-unrolled-insns
The maximum number of instructions that a loop should have if that loop
is unrolled, and if the loop is unrolled, it determines how many times
the loop code is unrolled.

@item max-average-unrolled-insns
The maximum number of instructions biased by probabilities of their execution
that a loop should have if that loop is unrolled, and if the loop is unrolled,
it determines how many times the loop code is unrolled.

@item max-unroll-times
The maximum number of unrollings of a single loop.

@item max-peeled-insns
The maximum number of instructions that a loop should have if that loop
is peeled, and if the loop is peeled, it determines how many times
the loop code is peeled.

@item max-peel-times
The maximum number of peelings of a single loop.

@item max-completely-peeled-insns
The maximum number of insns of a completely peeled loop.

@item max-completely-peel-times
The maximum number of iterations of a loop to be suitable for complete peeling.

@item max-unswitch-insns
The maximum number of insns of an unswitched loop.

@item max-unswitch-level
The maximum number of branches unswitched in a single loop.

@item hot-bb-count-fraction
Select fraction of the maximal count of repetitions of basic block in program
given basic block needs to have to be considered hot.

@item hot-bb-frequency-fraction
Select fraction of the maximal frequency of executions of basic block in
function given basic block needs to have to be considered hot

@item tracer-dynamic-coverage
@itemx tracer-dynamic-coverage-feedback

This value is used to limit superblock formation once the given percentage of
executed instructions is covered.  This limits unnecessary code size
expansion.

The @option{tracer-dynamic-coverage-feedback} is used only when profile
feedback is available.  The real profiles (as opposed to statically estimated
ones) are much less balanced allowing the threshold to be larger value.

@item tracer-max-code-growth
Stop tail duplication once code growth has reached given percentage.  This is
rather hokey argument, as most of the duplicates will be eliminated later in
cross jumping, so it may be set to much higher values than is the desired code
growth.

@item tracer-min-branch-ratio

Stop reverse growth when the reverse probability of best edge is less than this
threshold (in percent).

@item tracer-min-branch-ratio
@itemx tracer-min-branch-ratio-feedback

Stop forward growth if the best edge do have probability lower than this
threshold.

Similarly to @option{tracer-dynamic-coverage} two values are present, one for
compilation for profile feedback and one for compilation without.  The value
for compilation with profile feedback needs to be more conservative (higher) in
order to make tracer effective.

@item ggc-min-expand

GCC uses a garbage collector to manage its own memory allocation.  This
parameter specifies the minimum percentage by which the garbage
collector's heap should be allowed to expand between collections.
Tuning this may improve compilation speed; it has no effect on code
generation.

The default is 30% + 70% * (RAM/1GB) with an upper bound of 100% when
RAM >= 1GB.  If @code{getrlimit} is available, the notion of "RAM" is
the smallest of actual RAM, RLIMIT_RSS, RLIMIT_DATA and RLIMIT_AS.  If
GCC is not able to calculate RAM on a particular platform, the lower
bound of 30% is used.  Setting this parameter and
@option{ggc-min-heapsize} to zero causes a full collection to occur at
every opportunity.  This is extremely slow, but can be useful for
debugging.

@item ggc-min-heapsize

Minimum size of the garbage collector's heap before it begins bothering
to collect garbage.  The first collection occurs after the heap expands
by @option{ggc-min-expand}% beyond @option{ggc-min-heapsize}.  Again,
tuning this may improve compilation speed, and has no effect on code
generation.

The default is RAM/8, with a lower bound of 4096 (four megabytes) and an
upper bound of 131072 (128 megabytes).  If @code{getrlimit} is
available, the notion of "RAM" is the smallest of actual RAM,
RLIMIT_RSS, RLIMIT_DATA and RLIMIT_AS.  If GCC is not able to calculate
RAM on a particular platform, the lower bound is used.  Setting this
parameter very large effectively disables garbage collection.  Setting
this parameter and @option{ggc-min-expand} to zero causes a full
collection to occur at every opportunity.

@item reorder-blocks-duplicate
@itemx reorder-blocks-duplicate-feedback

Used by basic block reordering pass to decide whether to use uncondtional
branch or duplicate the code on it's destination.  Code is duplicated when it's
estimated size is smaller than this value multiplied by the estimated size of
unconditinal jump in the hot spots of the program.

The @option{reorder-block-duplicate-feedback} is used only when profile
feedback is available and may be set to higher values than
@option{reorder-block-duplicate} since information about the hot spots is more
accurate.
@end table
@end table

@node Preprocessor Options
@section Options Controlling the Preprocessor
@cindex preprocessor options
@cindex options, preprocessor

These options control the C preprocessor, which is run on each C source
file before actual compilation.

If you use the @option{-E} option, nothing is done except preprocessing.
Some of these options make sense only together with @option{-E} because
they cause the preprocessor output to be unsuitable for actual
compilation.

@table @gcctabopt
@opindex Wp
You can use @option{-Wp,@var{option}} to bypass the compiler driver
and pass @var{option} directly through to the preprocessor.  If
@var{option} contains commas, it is split into multiple options at the
commas.  However, many options are modified, translated or interpreted
by the compiler driver before being passed to the preprocessor, and
@option{-Wp} forcibly bypasses this phase.  The preprocessor's direct
interface is undocumented and subject to change, so whenever possible
you should avoid using @option{-Wp} and let the driver handle the
options instead.

@item -Xpreprocessor @var{option}
@opindex preprocessor
Pass @var{option} as an option to the preprocessor.  You can use this to
supply system-specific preprocessor options which GCC does not know how to
recognize.

If you want to pass an option that takes an argument, you must use
@option{-Xpreprocessor} twice, once for the option and once for the argument.
@end table

@include cppopts.texi

@node Assembler Options
@section Passing Options to the Assembler

@c prevent bad page break with this line
You can pass options to the assembler.

@table @gcctabopt
@item -Wa,@var{option}
@opindex Wa
Pass @var{option} as an option to the assembler.  If @var{option}
contains commas, it is split into multiple options at the commas.

@item -Xassembler @var{option}
@opindex Xassembler
Pass @var{option} as an option to the assembler.  You can use this to
supply system-specific assembler options which GCC does not know how to
recognize.

If you want to pass an option that takes an argument, you must use
@option{-Xassembler} twice, once for the option and once for the argument.

@end table

@node Link Options
@section Options for Linking
@cindex link options
@cindex options, linking

These options come into play when the compiler links object files into
an executable output file.  They are meaningless if the compiler is
not doing a link step.

@table @gcctabopt
@cindex file names
@item @var{object-file-name}
A file name that does not end in a special recognized suffix is
considered to name an object file or library.  (Object files are
distinguished from libraries by the linker according to the file
contents.)  If linking is done, these object files are used as input
to the linker.

@item -c
@itemx -S
@itemx -E
@opindex c
@opindex S
@opindex E
If any of these options is used, then the linker is not run, and
object file names should not be used as arguments.  @xref{Overall
Options}.

@cindex Libraries
@item -l@var{library}
@itemx -l @var{library}
@opindex l
Search the library named @var{library} when linking.  (The second
alternative with the library as a separate argument is only for
POSIX compliance and is not recommended.)

It makes a difference where in the command you write this option; the
linker searches and processes libraries and object files in the order they
are specified.  Thus, @samp{foo.o -lz bar.o} searches library @samp{z}
after file @file{foo.o} but before @file{bar.o}.  If @file{bar.o} refers
to functions in @samp{z}, those functions may not be loaded.

The linker searches a standard list of directories for the library,
which is actually a file named @file{lib@var{library}.a}.  The linker
then uses this file as if it had been specified precisely by name.

The directories searched include several standard system directories
plus any that you specify with @option{-L}.

Normally the files found this way are library files---archive files
whose members are object files.  The linker handles an archive file by
scanning through it for members which define symbols that have so far
been referenced but not defined.  But if the file that is found is an
ordinary object file, it is linked in the usual fashion.  The only
difference between using an @option{-l} option and specifying a file name
is that @option{-l} surrounds @var{library} with @samp{lib} and @samp{.a}
and searches several directories.

@item -lobjc
@opindex lobjc
You need this special case of the @option{-l} option in order to
link an Objective-C program.

@item -nostartfiles
@opindex nostartfiles
Do not use the standard system startup files when linking.
The standard system libraries are used normally, unless @option{-nostdlib}
or @option{-nodefaultlibs} is used.

@item -nodefaultlibs
@opindex nodefaultlibs
Do not use the standard system libraries when linking.
Only the libraries you specify will be passed to the linker.
The standard startup files are used normally, unless @option{-nostartfiles}
is used.  The compiler may generate calls to memcmp, memset, and memcpy
for System V (and ISO C) environments or to bcopy and bzero for
BSD environments.  These entries are usually resolved by entries in
libc.  These entry points should be supplied through some other
mechanism when this option is specified.

@item -nostdlib
@opindex nostdlib
Do not use the standard system startup files or libraries when linking.
No startup files and only the libraries you specify will be passed to
the linker.  The compiler may generate calls to memcmp, memset, and memcpy
for System V (and ISO C) environments or to bcopy and bzero for
BSD environments.  These entries are usually resolved by entries in
libc.  These entry points should be supplied through some other
mechanism when this option is specified.

@cindex @option{-lgcc}, use with @option{-nostdlib}
@cindex @option{-nostdlib} and unresolved references
@cindex unresolved references and @option{-nostdlib}
@cindex @option{-lgcc}, use with @option{-nodefaultlibs}
@cindex @option{-nodefaultlibs} and unresolved references
@cindex unresolved references and @option{-nodefaultlibs}
One of the standard libraries bypassed by @option{-nostdlib} and
@option{-nodefaultlibs} is @file{libgcc.a}, a library of internal subroutines
that GCC uses to overcome shortcomings of particular machines, or special
needs for some languages.
(@xref{Interface,,Interfacing to GCC Output,gccint,GNU Compiler
Collection (GCC) Internals},
for more discussion of @file{libgcc.a}.)
In most cases, you need @file{libgcc.a} even when you want to avoid
other standard libraries.  In other words, when you specify @option{-nostdlib}
or @option{-nodefaultlibs} you should usually specify @option{-lgcc} as well.
This ensures that you have no unresolved references to internal GCC
library subroutines.  (For example, @samp{__main}, used to ensure C++
constructors will be called; @pxref{Collect2,,@code{collect2}, gccint,
GNU Compiler Collection (GCC) Internals}.)

@item -s
@opindex s
Remove all symbol table and relocation information from the executable.

@item -static
@opindex static
On systems that support dynamic linking, this prevents linking with the shared
libraries.  On other systems, this option has no effect.

@item -shared
@opindex shared
Produce a shared object which can then be linked with other objects to
form an executable.  Not all systems support this option.  For predictable
results, you must also specify the same set of options that were used to
generate code (@option{-fpic}, @option{-fPIC}, or model suboptions)
when you specify this option.@footnote{On some systems, @samp{gcc -shared}
needs to build supplementary stub code for constructors to work.  On
multi-libbed systems, @samp{gcc -shared} must select the correct support
libraries to link against.  Failing to supply the correct flags may lead
to subtle defects.  Supplying them in cases where they are not necessary
is innocuous.}

@item -shared-libgcc
@itemx -static-libgcc
@opindex shared-libgcc
@opindex static-libgcc
On systems that provide @file{libgcc} as a shared library, these options
force the use of either the shared or static version respectively.
If no shared version of @file{libgcc} was built when the compiler was
configured, these options have no effect.

There are several situations in which an application should use the
shared @file{libgcc} instead of the static version.  The most common
of these is when the application wishes to throw and catch exceptions
across different shared libraries.  In that case, each of the libraries
as well as the application itself should use the shared @file{libgcc}.

Therefore, the G++ and GCJ drivers automatically add
@option{-shared-libgcc} whenever you build a shared library or a main
executable, because C++ and Java programs typically use exceptions, so
this is the right thing to do.

If, instead, you use the GCC driver to create shared libraries, you may
find that they will not always be linked with the shared @file{libgcc}.
If GCC finds, at its configuration time, that you have a GNU linker that
does not support option @option{--eh-frame-hdr}, it will link the shared
version of @file{libgcc} into shared libraries by default.  Otherwise,
it will take advantage of the linker and optimize away the linking with
the shared version of @file{libgcc}, linking with the static version of
libgcc by default.  This allows exceptions to propagate through such
shared libraries, without incurring relocation costs at library load
time.

However, if a library or main executable is supposed to throw or catch
exceptions, you must link it using the G++ or GCJ driver, as appropriate
for the languages used in the program, or using the option
@option{-shared-libgcc}, such that it is linked with the shared
@file{libgcc}.

@item -symbolic
@opindex symbolic
Bind references to global symbols when building a shared object.  Warn
about any unresolved references (unless overridden by the link editor
option @samp{-Xlinker -z -Xlinker defs}).  Only a few systems support
this option.

@item -Xlinker @var{option}
@opindex Xlinker
Pass @var{option} as an option to the linker.  You can use this to
supply system-specific linker options which GCC does not know how to
recognize.

If you want to pass an option that takes an argument, you must use
@option{-Xlinker} twice, once for the option and once for the argument.
For example, to pass @option{-assert definitions}, you must write
@samp{-Xlinker -assert -Xlinker definitions}.  It does not work to write
@option{-Xlinker "-assert definitions"}, because this passes the entire
string as a single argument, which is not what the linker expects.

@item -Wl,@var{option}
@opindex Wl
Pass @var{option} as an option to the linker.  If @var{option} contains
commas, it is split into multiple options at the commas.

@item -u @var{symbol}
@opindex u
Pretend the symbol @var{symbol} is undefined, to force linking of
library modules to define it.  You can use @option{-u} multiple times with
different symbols to force loading of additional library modules.
@end table

@node Directory Options
@section Options for Directory Search
@cindex directory options
@cindex options, directory search
@cindex search path

These options specify directories to search for header files, for
libraries and for parts of the compiler:

@table @gcctabopt
@item -I@var{dir}
@opindex I
Add the directory @var{dir} to the head of the list of directories to be
searched for header files.  This can be used to override a system header
file, substituting your own version, since these directories are
searched before the system header file directories.  However, you should
not use this option to add directories that contain vendor-supplied
system header files (use @option{-isystem} for that).  If you use more than
one @option{-I} option, the directories are scanned in left-to-right
order; the standard system directories come after.

If a standard system include directory, or a directory specified with
@option{-isystem}, is also specified with @option{-I}, the @option{-I}
option will be ignored.  The directory will still be searched but as a
system directory at its normal position in the system include chain.
This is to ensure that GCC's procedure to fix buggy system headers and
the ordering for the include_next directive are not inadvertently changed.
If you really need to change the search order for system directories,
use the @option{-nostdinc} and/or @option{-isystem} options.

@item -I-
@opindex I-
Any directories you specify with @option{-I} options before the @option{-I-}
option are searched only for the case of @samp{#include "@var{file}"};
they are not searched for @samp{#include <@var{file}>}.

If additional directories are specified with @option{-I} options after
the @option{-I-}, these directories are searched for all @samp{#include}
directives.  (Ordinarily @emph{all} @option{-I} directories are used
this way.)

In addition, the @option{-I-} option inhibits the use of the current
directory (where the current input file came from) as the first search
directory for @samp{#include "@var{file}"}.  There is no way to
override this effect of @option{-I-}.  With @option{-I.} you can specify
searching the directory which was current when the compiler was
invoked.  That is not exactly the same as what the preprocessor does
by default, but it is often satisfactory.

@option{-I-} does not inhibit the use of the standard system directories
for header files.  Thus, @option{-I-} and @option{-nostdinc} are
independent.

@item -L@var{dir}
@opindex L
Add directory @var{dir} to the list of directories to be searched
for @option{-l}.

@item -B@var{prefix}
@opindex B
This option specifies where to find the executables, libraries,
include files, and data files of the compiler itself.

The compiler driver program runs one or more of the subprograms
@file{cpp}, @file{cc1}, @file{as} and @file{ld}.  It tries
@var{prefix} as a prefix for each program it tries to run, both with and
without @samp{@var{machine}/@var{version}/} (@pxref{Target Options}).

For each subprogram to be run, the compiler driver first tries the
@option{-B} prefix, if any.  If that name is not found, or if @option{-B}
was not specified, the driver tries two standard prefixes, which are
@file{/usr/lib/gcc/} and @file{/usr/local/lib/gcc-lib/}.  If neither of
those results in a file name that is found, the unmodified program
name is searched for using the directories specified in your
@env{PATH} environment variable.

The compiler will check to see if the path provided by the @option{-B}
refers to a directory, and if necessary it will add a directory
separator character at the end of the path.

@option{-B} prefixes that effectively specify directory names also apply
to libraries in the linker, because the compiler translates these
options into @option{-L} options for the linker.  They also apply to
includes files in the preprocessor, because the compiler translates these
options into @option{-isystem} options for the preprocessor.  In this case,
the compiler appends @samp{include} to the prefix.

The run-time support file @file{libgcc.a} can also be searched for using
the @option{-B} prefix, if needed.  If it is not found there, the two
standard prefixes above are tried, and that is all.  The file is left
out of the link if it is not found by those means.

Another way to specify a prefix much like the @option{-B} prefix is to use
the environment variable @env{GCC_EXEC_PREFIX}.  @xref{Environment
Variables}.

As a special kludge, if the path provided by @option{-B} is
@file{[dir/]stage@var{N}/}, where @var{N} is a number in the range 0 to
9, then it will be replaced by @file{[dir/]include}.  This is to help
with boot-strapping the compiler.

@item -specs=@var{file}
@opindex specs
Process @var{file} after the compiler reads in the standard @file{specs}
file, in order to override the defaults that the @file{gcc} driver
program uses when determining what switches to pass to @file{cc1},
@file{cc1plus}, @file{as}, @file{ld}, etc.  More than one
@option{-specs=@var{file}} can be specified on the command line, and they
are processed in order, from left to right.
@end table

@c man end

@node Spec Files
@section Specifying subprocesses and the switches to pass to them
@cindex Spec Files

@command{gcc} is a driver program.  It performs its job by invoking a
sequence of other programs to do the work of compiling, assembling and
linking.  GCC interprets its command-line parameters and uses these to
deduce which programs it should invoke, and which command-line options
it ought to place on their command lines.  This behavior is controlled
by @dfn{spec strings}.  In most cases there is one spec string for each
program that GCC can invoke, but a few programs have multiple spec
strings to control their behavior.  The spec strings built into GCC can
be overridden by using the @option{-specs=} command-line switch to specify
a spec file.

@dfn{Spec files} are plaintext files that are used to construct spec
strings.  They consist of a sequence of directives separated by blank
lines.  The type of directive is determined by the first non-whitespace
character on the line and it can be one of the following:

@table @code
@item %@var{command}
Issues a @var{command} to the spec file processor.  The commands that can
appear here are:

@table @code
@item %include <@var{file}>
@cindex %include
Search for @var{file} and insert its text at the current point in the
specs file.

@item %include_noerr <@var{file}>
@cindex %include_noerr
Just like @samp{%include}, but do not generate an error message if the include
file cannot be found.

@item %rename @var{old_name} @var{new_name}
@cindex %rename
Rename the spec string @var{old_name} to @var{new_name}.

@end table

@item *[@var{spec_name}]:
This tells the compiler to create, override or delete the named spec
string.  All lines after this directive up to the next directive or
blank line are considered to be the text for the spec string.  If this
results in an empty string then the spec will be deleted.  (Or, if the
spec did not exist, then nothing will happened.)  Otherwise, if the spec
does not currently exist a new spec will be created.  If the spec does
exist then its contents will be overridden by the text of this
directive, unless the first character of that text is the @samp{+}
character, in which case the text will be appended to the spec.

@item [@var{suffix}]:
Creates a new @samp{[@var{suffix}] spec} pair.  All lines after this directive
and up to the next directive or blank line are considered to make up the
spec string for the indicated suffix.  When the compiler encounters an
input file with the named suffix, it will processes the spec string in
order to work out how to compile that file.  For example:

@smallexample
.ZZ:
z-compile -input %i
@end smallexample

This says that any input file whose name ends in @samp{.ZZ} should be
passed to the program @samp{z-compile}, which should be invoked with the
command-line switch @option{-input} and with the result of performing the
@samp{%i} substitution.  (See below.)

As an alternative to providing a spec string, the text that follows a
suffix directive can be one of the following:

@table @code
@item @@@var{language}
This says that the suffix is an alias for a known @var{language}.  This is
similar to using the @option{-x} command-line switch to GCC to specify a
language explicitly.  For example:

@smallexample
.ZZ:
@@c++
@end smallexample

Says that .ZZ files are, in fact, C++ source files.

@item #@var{name}
This causes an error messages saying:

@smallexample
@var{name} compiler not installed on this system.
@end smallexample
@end table

GCC already has an extensive list of suffixes built into it.
This directive will add an entry to the end of the list of suffixes, but
since the list is searched from the end backwards, it is effectively
possible to override earlier entries using this technique.

@end table

GCC has the following spec strings built into it.  Spec files can
override these strings or create their own.  Note that individual
targets can also add their own spec strings to this list.

@smallexample
asm          Options to pass to the assembler
asm_final    Options to pass to the assembler post-processor
cpp          Options to pass to the C preprocessor
cc1          Options to pass to the C compiler
cc1plus      Options to pass to the C++ compiler
endfile      Object files to include at the end of the link
link         Options to pass to the linker
lib          Libraries to include on the command line to the linker
libgcc       Decides which GCC support library to pass to the linker
linker       Sets the name of the linker
predefines   Defines to be passed to the C preprocessor
signed_char  Defines to pass to CPP to say whether @code{char} is signed
             by default
startfile    Object files to include at the start of the link
@end smallexample

Here is a small example of a spec file:

@smallexample
%rename lib                 old_lib

*lib:
--start-group -lgcc -lc -leval1 --end-group %(old_lib)
@end smallexample

This example renames the spec called @samp{lib} to @samp{old_lib} and
then overrides the previous definition of @samp{lib} with a new one.
The new definition adds in some extra command-line options before
including the text of the old definition.

@dfn{Spec strings} are a list of command-line options to be passed to their
corresponding program.  In addition, the spec strings can contain
@samp{%}-prefixed sequences to substitute variable text or to
conditionally insert text into the command line.  Using these constructs
it is possible to generate quite complex command lines.

Here is a table of all defined @samp{%}-sequences for spec
strings.  Note that spaces are not generated automatically around the
results of expanding these sequences.  Therefore you can concatenate them
together or combine them with constant text in a single argument.

@table @code
@item %%
Substitute one @samp{%} into the program name or argument.

@item %i
Substitute the name of the input file being processed.

@item %b
Substitute the basename of the input file being processed.
This is the substring up to (and not including) the last period
and not including the directory.

@item %B
This is the same as @samp{%b}, but include the file suffix (text after
the last period).

@item %d
Marks the argument containing or following the @samp{%d} as a
temporary file name, so that that file will be deleted if GCC exits
successfully.  Unlike @samp{%g}, this contributes no text to the
argument.

@item %g@var{suffix}
Substitute a file name that has suffix @var{suffix} and is chosen
once per compilation, and mark the argument in the same way as
@samp{%d}.  To reduce exposure to denial-of-service attacks, the file
name is now chosen in a way that is hard to predict even when previously
chosen file names are known.  For example, @samp{%g.s @dots{} %g.o @dots{} %g.s}
might turn into @samp{ccUVUUAU.s ccXYAXZ12.o ccUVUUAU.s}.  @var{suffix} matches
the regexp @samp{[.A-Za-z]*} or the special string @samp{%O}, which is
treated exactly as if @samp{%O} had been preprocessed.  Previously, @samp{%g}
was simply substituted with a file name chosen once per compilation,
without regard to any appended suffix (which was therefore treated
just like ordinary text), making such attacks more likely to succeed.

@item %u@var{suffix}
Like @samp{%g}, but generates a new temporary file name even if
@samp{%u@var{suffix}} was already seen.

@item %U@var{suffix}
Substitutes the last file name generated with @samp{%u@var{suffix}}, generating a
new one if there is no such last file name.  In the absence of any
@samp{%u@var{suffix}}, this is just like @samp{%g@var{suffix}}, except they don't share
the same suffix @emph{space}, so @samp{%g.s @dots{} %U.s @dots{} %g.s @dots{} %U.s}
would involve the generation of two distinct file names, one
for each @samp{%g.s} and another for each @samp{%U.s}.  Previously, @samp{%U} was
simply substituted with a file name chosen for the previous @samp{%u},
without regard to any appended suffix.

@item %j@var{suffix}
Substitutes the name of the @code{HOST_BIT_BUCKET}, if any, and if it is
writable, and if save-temps is off; otherwise, substitute the name
of a temporary file, just like @samp{%u}.  This temporary file is not
meant for communication between processes, but rather as a junk
disposal mechanism.

@item %|@var{suffix}
@itemx %m@var{suffix}
Like @samp{%g}, except if @option{-pipe} is in effect.  In that case
@samp{%|} substitutes a single dash and @samp{%m} substitutes nothing at
all.  These are the two most common ways to instruct a program that it
should read from standard input or write to standard output.  If you
need something more elaborate you can use an @samp{%@{pipe:@code{X}@}}
construct: see for example @file{f/lang-specs.h}.

@item %.@var{SUFFIX}
Substitutes @var{.SUFFIX} for the suffixes of a matched switch's args
when it is subsequently output with @samp{%*}.  @var{SUFFIX} is
terminated by the next space or %.

@item %w
Marks the argument containing or following the @samp{%w} as the
designated output file of this compilation.  This puts the argument
into the sequence of arguments that @samp{%o} will substitute later.

@item %o
Substitutes the names of all the output files, with spaces
automatically placed around them.  You should write spaces
around the @samp{%o} as well or the results are undefined.
@samp{%o} is for use in the specs for running the linker.
Input files whose names have no recognized suffix are not compiled
at all, but they are included among the output files, so they will
be linked.

@item %O
Substitutes the suffix for object files.  Note that this is
handled specially when it immediately follows @samp{%g, %u, or %U},
because of the need for those to form complete file names.  The
handling is such that @samp{%O} is treated exactly as if it had already
been substituted, except that @samp{%g, %u, and %U} do not currently
support additional @var{suffix} characters following @samp{%O} as they would
following, for example, @samp{.o}.

@item %p
Substitutes the standard macro predefinitions for the
current target machine.  Use this when running @code{cpp}.

@item %P
Like @samp{%p}, but puts @samp{__} before and after the name of each
predefined macro, except for macros that start with @samp{__} or with
@samp{_@var{L}}, where @var{L} is an uppercase letter.  This is for ISO
C@.

@item %I
Substitute any of @option{-iprefix} (made from @env{GCC_EXEC_PREFIX}),
@option{-isysroot} (made from @env{TARGET_SYSTEM_ROOT}), and
@option{-isystem} (made from @env{COMPILER_PATH} and @option{-B} options)
as necessary.

@item %s
Current argument is the name of a library or startup file of some sort.
Search for that file in a standard list of directories and substitute
the full name found.

@item %e@var{str}
Print @var{str} as an error message.  @var{str} is terminated by a newline.
Use this when inconsistent options are detected.

@item %(@var{name})
Substitute the contents of spec string @var{name} at this point.

@item %[@var{name}]
Like @samp{%(@dots{})} but put @samp{__} around @option{-D} arguments.

@item %x@{@var{option}@}
Accumulate an option for @samp{%X}.

@item %X
Output the accumulated linker options specified by @option{-Wl} or a @samp{%x}
spec string.

@item %Y
Output the accumulated assembler options specified by @option{-Wa}.

@item %Z
Output the accumulated preprocessor options specified by @option{-Wp}.

@item %a
Process the @code{asm} spec.  This is used to compute the
switches to be passed to the assembler.

@item %A
Process the @code{asm_final} spec.  This is a spec string for
passing switches to an assembler post-processor, if such a program is
needed.

@item %l
Process the @code{link} spec.  This is the spec for computing the
command line passed to the linker.  Typically it will make use of the
@samp{%L %G %S %D and %E} sequences.

@item %D
Dump out a @option{-L} option for each directory that GCC believes might
contain startup files.  If the target supports multilibs then the
current multilib directory will be prepended to each of these paths.

@item %M
Output the multilib directory with directory separators replaced with
@samp{_}.  If multilib directories are not set, or the multilib directory is
@file{.} then this option emits nothing.

@item %L
Process the @code{lib} spec.  This is a spec string for deciding which
libraries should be included on the command line to the linker.

@item %G
Process the @code{libgcc} spec.  This is a spec string for deciding
which GCC support library should be included on the command line to the linker.

@item %S
Process the @code{startfile} spec.  This is a spec for deciding which
object files should be the first ones passed to the linker.  Typically
this might be a file named @file{crt0.o}.

@item %E
Process the @code{endfile} spec.  This is a spec string that specifies
the last object files that will be passed to the linker.

@item %C
Process the @code{cpp} spec.  This is used to construct the arguments
to be passed to the C preprocessor.

@item %c
Process the @code{signed_char} spec.  This is intended to be used
to tell cpp whether a char is signed.  It typically has the definition:
@smallexample
%@{funsigned-char:-D__CHAR_UNSIGNED__@}
@end smallexample

@item %1
Process the @code{cc1} spec.  This is used to construct the options to be
passed to the actual C compiler (@samp{cc1}).

@item %2
Process the @code{cc1plus} spec.  This is used to construct the options to be
passed to the actual C++ compiler (@samp{cc1plus}).

@item %*
Substitute the variable part of a matched option.  See below.
Note that each comma in the substituted string is replaced by
a single space.

@item %<@code{S}
Remove all occurrences of @code{-S} from the command line.  Note---this
command is position dependent.  @samp{%} commands in the spec string
before this one will see @code{-S}, @samp{%} commands in the spec string
after this one will not.

@item %:@var{function}(@var{args})
Call the named function @var{function}, passing it @var{args}.
@var{args} is first processed as a nested spec string, then split
into an argument vector in the usual fashion.  The function returns
a string which is processed as if it had appeared literally as part
of the current spec.

The following built-in spec functions are provided:

@table @code
@item @code{if-exists}
The @code{if-exists} spec function takes one argument, an absolute
pathname to a file.  If the file exists, @code{if-exists} returns the
pathname.  Here is a small example of its usage:

@smallexample
*startfile:
crt0%O%s %:if-exists(crti%O%s) crtbegin%O%s
@end smallexample

@item @code{if-exists-else}
The @code{if-exists-else} spec function is similar to the @code{if-exists}
spec function, except that it takes two arguments.  The first argument is
an absolute pathname to a file.  If the file exists, @code{if-exists-else}
returns the pathname.  If it does not exist, it returns the second argument.
This way, @code{if-exists-else} can be used to select one file or another,
based on the existence of the first.  Here is a small example of its usage:

@smallexample 
*startfile:
crt0%O%s %:if-exists(crti%O%s) \
%:if-exists-else(crtbeginT%O%s crtbegin%O%s)
@end smallexample
@end table 

@item %@{@code{S}@}
Substitutes the @code{-S} switch, if that switch was given to GCC@.
If that switch was not specified, this substitutes nothing.  Note that
the leading dash is omitted when specifying this option, and it is
automatically inserted if the substitution is performed.  Thus the spec
string @samp{%@{foo@}} would match the command-line option @option{-foo}
and would output the command line option @option{-foo}.

@item %W@{@code{S}@}
Like %@{@code{S}@} but mark last argument supplied within as a file to be
deleted on failure.

@item %@{@code{S}*@}
Substitutes all the switches specified to GCC whose names start
with @code{-S}, but which also take an argument.  This is used for
switches like @option{-o}, @option{-D}, @option{-I}, etc.
GCC considers @option{-o foo} as being
one switch whose names starts with @samp{o}.  %@{o*@} would substitute this
text, including the space.  Thus two arguments would be generated.

@item %@{@code{S}*&@code{T}*@}
Like %@{@code{S}*@}, but preserve order of @code{S} and @code{T} options
(the order of @code{S} and @code{T} in the spec is not significant).
There can be any number of ampersand-separated variables; for each the
wild card is optional.  Useful for CPP as @samp{%@{D*&U*&A*@}}.

@item %@{@code{S}:@code{X}@}
Substitutes @code{X}, if the @samp{-S} switch was given to GCC@.

@item %@{!@code{S}:@code{X}@}
Substitutes @code{X}, if the @samp{-S} switch was @emph{not} given to GCC@.

@item %@{@code{S}*:@code{X}@}
Substitutes @code{X} if one or more switches whose names start with
@code{-S} are specified to GCC@.  Normally @code{X} is substituted only
once, no matter how many such switches appeared.  However, if @code{%*}
appears somewhere in @code{X}, then @code{X} will be substituted once
for each matching switch, with the @code{%*} replaced by the part of
that switch that matched the @code{*}.

@item %@{.@code{S}:@code{X}@}
Substitutes @code{X}, if processing a file with suffix @code{S}.

@item %@{!.@code{S}:@code{X}@}
Substitutes @code{X}, if @emph{not} processing a file with suffix @code{S}.

@item %@{@code{S}|@code{P}:@code{X}@}
Substitutes @code{X} if either @code{-S} or @code{-P} was given to GCC@.
This may be combined with @samp{!}, @samp{.}, and @code{*} sequences as well,
although they have a stronger binding than the @samp{|}.  If @code{%*}
appears in @code{X}, all of the alternatives must be starred, and only
the first matching alternative is substituted.

For example, a spec string like this:

@smallexample
%@{.c:-foo@} %@{!.c:-bar@} %@{.c|d:-baz@} %@{!.c|d:-boggle@}
@end smallexample

will output the following command-line options from the following input
command-line options:

@smallexample
fred.c        -foo -baz
jim.d         -bar -boggle
-d fred.c     -foo -baz -boggle
-d jim.d      -bar -baz -boggle
@end smallexample

@item %@{S:X; T:Y; :D@}

If @code{S} was given to GCC, substitues @code{X}; else if @code{T} was
given to GCC, substitues @code{Y}; else substitutes @code{D}.  There can
be as many clauses as you need.  This may be combined with @code{.}, 
@code{!}, @code{|}, and @code{*} as needed.


@end table

The conditional text @code{X} in a %@{@code{S}:@code{X}@} or similar
construct may contain other nested @samp{%} constructs or spaces, or
even newlines.  They are processed as usual, as described above.
Trailing white space in @code{X} is ignored.  White space may also
appear anywhere on the left side of the colon in these constructs,
except between @code{.} or @code{*} and the corresponding word.

The @option{-O}, @option{-f}, @option{-m}, and @option{-W} switches are
handled specifically in these constructs.  If another value of
@option{-O} or the negated form of a @option{-f}, @option{-m}, or
@option{-W} switch is found later in the command line, the earlier
switch value is ignored, except with @{@code{S}*@} where @code{S} is
just one letter, which passes all matching options.

The character @samp{|} at the beginning of the predicate text is used to
indicate that a command should be piped to the following command, but
only if @option{-pipe} is specified.

It is built into GCC which switches take arguments and which do not.
(You might think it would be useful to generalize this to allow each
compiler's spec to say which switches take arguments.  But this cannot
be done in a consistent fashion.  GCC cannot even decide which input
files have been specified without knowing which switches take arguments,
and it must know which input files to compile in order to tell which
compilers to run).

GCC also knows implicitly that arguments starting in @option{-l} are to be
treated as compiler output files, and passed to the linker in their
proper position among the other output files.

@c man begin OPTIONS

@node Target Options
@section Specifying Target Machine and Compiler Version
@cindex target options
@cindex cross compiling
@cindex specifying machine version
@cindex specifying compiler version and target machine
@cindex compiler version, specifying
@cindex target machine, specifying

The usual way to run GCC is to run the executable called @file{gcc}, or
@file{<machine>-gcc} when cross-compiling, or
@file{<machine>-gcc-<version>} to run a version other than the one that
was installed last.  Sometimes this is inconvenient, so GCC provides
options that will switch to another cross-compiler or version.

@table @gcctabopt
@item -b @var{machine}
@opindex b
The argument @var{machine} specifies the target machine for compilation.

The value to use for @var{machine} is the same as was specified as the
machine type when configuring GCC as a cross-compiler.  For
example, if a cross-compiler was configured with @samp{configure
i386v}, meaning to compile for an 80386 running System V, then you
would specify @option{-b i386v} to run that cross compiler.

@item -V @var{version}
@opindex V
The argument @var{version} specifies which version of GCC to run.
This is useful when multiple versions are installed.  For example,
@var{version} might be @samp{2.0}, meaning to run GCC version 2.0.
@end table

The @option{-V} and @option{-b} options work by running the
@file{<machine>-gcc-<version>} executable, so there's no real reason to
use them if you can just run that directly.

@node Submodel Options
@section Hardware Models and Configurations
@cindex submodel options
@cindex specifying hardware config
@cindex hardware models and configurations, specifying
@cindex machine dependent options

Earlier we discussed the standard option @option{-b} which chooses among
different installed compilers for completely different target
machines, such as VAX vs.@: 68000 vs.@: 80386.

In addition, each of these target machine types can have its own
special options, starting with @samp{-m}, to choose among various
hardware models or configurations---for example, 68010 vs 68020,
floating coprocessor or none.  A single installed version of the
compiler can compile for any model or configuration, according to the
options specified.

Some configurations of the compiler also support additional special
options, usually for compatibility with other compilers on the same
platform.

These options are defined by the macro @code{TARGET_SWITCHES} in the
machine description.  The default for the options is also defined by
that macro, which enables you to change the defaults.

@menu
* M680x0 Options::
* M68hc1x Options::
* VAX Options::
* SPARC Options::
* ARM Options::
* MN10200 Options::
* MN10300 Options::
* M32R/D Options::
* M88K Options::
* RS/6000 and PowerPC Options::
* Darwin Options::
* RT Options::
* MIPS Options::
* i386 and x86-64 Options::
* HPPA Options::
* Intel 960 Options::
* DEC Alpha Options::
* DEC Alpha/VMS Options::
* H8/300 Options::
* SH Options::
* System V Options::
* TMS320C3x/C4x Options::
* V850 Options::
* ARC Options::
* NS32K Options::
* AVR Options::
* MCore Options::
* IA-64 Options::
* D30V Options::
* S/390 and zSeries Options::
* CRIS Options::
* MMIX Options::
* PDP-11 Options::
* Xstormy16 Options::
* Xtensa Options::
* FRV Options::
@end menu

@node M680x0 Options
@subsection M680x0 Options
@cindex M680x0 options

These are the @samp{-m} options defined for the 68000 series.  The default
values for these options depends on which style of 68000 was selected when
the compiler was configured; the defaults for the most common choices are
given below.

@table @gcctabopt
@item -m68000
@itemx -mc68000
@opindex m68000
@opindex mc68000
Generate output for a 68000.  This is the default
when the compiler is configured for 68000-based systems.

Use this option for microcontrollers with a 68000 or EC000 core,
including the 68008, 68302, 68306, 68307, 68322, 68328 and 68356.

@item -m68020
@itemx -mc68020
@opindex m68020
@opindex mc68020
Generate output for a 68020.  This is the default
when the compiler is configured for 68020-based systems.

@item -m68881
@opindex m68881
Generate output containing 68881 instructions for floating point.
This is the default for most 68020 systems unless @option{--nfp} was
specified when the compiler was configured.

@item -m68030
@opindex m68030
Generate output for a 68030.  This is the default when the compiler is
configured for 68030-based systems.

@item -m68040
@opindex m68040
Generate output for a 68040.  This is the default when the compiler is
configured for 68040-based systems.

This option inhibits the use of 68881/68882 instructions that have to be
emulated by software on the 68040.  Use this option if your 68040 does not
have code to emulate those instructions.

@item -m68060
@opindex m68060
Generate output for a 68060.  This is the default when the compiler is
configured for 68060-based systems.

This option inhibits the use of 68020 and 68881/68882 instructions that
have to be emulated by software on the 68060.  Use this option if your 68060
does not have code to emulate those instructions.

@item -mcpu32
@opindex mcpu32
Generate output for a CPU32.  This is the default
when the compiler is configured for CPU32-based systems.

Use this option for microcontrollers with a
CPU32 or CPU32+ core, including the 68330, 68331, 68332, 68333, 68334,
68336, 68340, 68341, 68349 and 68360.

@item -m5200
@opindex m5200
Generate output for a 520X ``coldfire'' family cpu.  This is the default
when the compiler is configured for 520X-based systems.

Use this option for microcontroller with a 5200 core, including
the MCF5202, MCF5203, MCF5204 and MCF5202.


@item -m68020-40
@opindex m68020-40
Generate output for a 68040, without using any of the new instructions.
This results in code which can run relatively efficiently on either a
68020/68881 or a 68030 or a 68040.  The generated code does use the
68881 instructions that are emulated on the 68040.

@item -m68020-60
@opindex m68020-60
Generate output for a 68060, without using any of the new instructions.
This results in code which can run relatively efficiently on either a
68020/68881 or a 68030 or a 68040.  The generated code does use the
68881 instructions that are emulated on the 68060.

@item -msoft-float
@opindex msoft-float
Generate output containing library calls for floating point.
@strong{Warning:} the requisite libraries are not available for all m68k
targets.  Normally the facilities of the machine's usual C compiler are
used, but this can't be done directly in cross-compilation.  You must
make your own arrangements to provide suitable library functions for
cross-compilation.  The embedded targets @samp{m68k-*-aout} and
@samp{m68k-*-coff} do provide software floating point support.

@item -mshort
@opindex mshort
Consider type @code{int} to be 16 bits wide, like @code{short int}.

@item -mnobitfield
@opindex mnobitfield
Do not use the bit-field instructions.  The @option{-m68000}, @option{-mcpu32}
and @option{-m5200} options imply @w{@option{-mnobitfield}}.

@item -mbitfield
@opindex mbitfield
Do use the bit-field instructions.  The @option{-m68020} option implies
@option{-mbitfield}.  This is the default if you use a configuration
designed for a 68020.

@item -mrtd
@opindex mrtd
Use a different function-calling convention, in which functions
that take a fixed number of arguments return with the @code{rtd}
instruction, which pops their arguments while returning.  This
saves one instruction in the caller since there is no need to pop
the arguments there.

This calling convention is incompatible with the one normally
used on Unix, so you cannot use it if you need to call libraries
compiled with the Unix compiler.

Also, you must provide function prototypes for all functions that
take variable numbers of arguments (including @code{printf});
otherwise incorrect code will be generated for calls to those
functions.

In addition, seriously incorrect code will result if you call a
function with too many arguments.  (Normally, extra arguments are
harmlessly ignored.)

The @code{rtd} instruction is supported by the 68010, 68020, 68030,
68040, 68060 and CPU32 processors, but not by the 68000 or 5200.

@item -malign-int
@itemx -mno-align-int
@opindex malign-int
@opindex mno-align-int
Control whether GCC aligns @code{int}, @code{long}, @code{long long},
@code{float}, @code{double}, and @code{long double} variables on a 32-bit
boundary (@option{-malign-int}) or a 16-bit boundary (@option{-mno-align-int}).
Aligning variables on 32-bit boundaries produces code that runs somewhat
faster on processors with 32-bit busses at the expense of more memory.

@strong{Warning:} if you use the @option{-malign-int} switch, GCC will
align structures containing the above types  differently than
most published application binary interface specifications for the m68k.

@item -mpcrel
@opindex mpcrel
Use the pc-relative addressing mode of the 68000 directly, instead of
using a global offset table.  At present, this option implies @option{-fpic},
allowing at most a 16-bit offset for pc-relative addressing.  @option{-fPIC} is
not presently supported with @option{-mpcrel}, though this could be supported for
68020 and higher processors.

@item -mno-strict-align
@itemx -mstrict-align
@opindex mno-strict-align
@opindex mstrict-align
Do not (do) assume that unaligned memory references will be handled by
the system.

@end table

@node M68hc1x Options
@subsection M68hc1x Options
@cindex M68hc1x options

These are the @samp{-m} options defined for the 68hc11 and 68hc12
microcontrollers.  The default values for these options depends on
which style of microcontroller was selected when the compiler was configured;
the defaults for the most common choices are given below.

@table @gcctabopt
@item -m6811
@itemx -m68hc11
@opindex m6811
@opindex m68hc11
Generate output for a 68HC11.  This is the default
when the compiler is configured for 68HC11-based systems.

@item -m6812
@itemx -m68hc12
@opindex m6812
@opindex m68hc12
Generate output for a 68HC12.  This is the default
when the compiler is configured for 68HC12-based systems.

@item -m68S12
@itemx -m68hcs12
@opindex m68S12
@opindex m68hcs12
Generate output for a 68HCS12.  

@item -mauto-incdec
@opindex mauto-incdec
Enable the use of 68HC12 pre and post auto-increment and auto-decrement
addressing modes.

@item -minmax
@itemx -nominmax
@opindex minmax
@opindex mnominmax
Enable the use of 68HC12 min and max instructions.

@item -mlong-calls
@itemx -mno-long-calls
@opindex mlong-calls
@opindex mno-long-calls
Treat all calls as being far away (near).  If calls are assumed to be
far away, the compiler will use the @code{call} instruction to
call a function and the @code{rtc} instruction for returning.

@item -mshort
@opindex mshort
Consider type @code{int} to be 16 bits wide, like @code{short int}.

@item -msoft-reg-count=@var{count}
@opindex msoft-reg-count
Specify the number of pseudo-soft registers which are used for the
code generation.  The maximum number is 32.  Using more pseudo-soft
register may or may not result in better code depending on the program.
The default is 4 for 68HC11 and 2 for 68HC12.

@end table

@node VAX Options
@subsection VAX Options
@cindex VAX options

These @samp{-m} options are defined for the VAX:

@table @gcctabopt
@item -munix
@opindex munix
Do not output certain jump instructions (@code{aobleq} and so on)
that the Unix assembler for the VAX cannot handle across long
ranges.

@item -mgnu
@opindex mgnu
Do output those jump instructions, on the assumption that you
will assemble with the GNU assembler.

@item -mg
@opindex mg
Output code for g-format floating point numbers instead of d-format.
@end table

@node SPARC Options
@subsection SPARC Options
@cindex SPARC options

These @samp{-m} switches are supported on the SPARC:

@table @gcctabopt
@item -mno-app-regs
@itemx -mapp-regs
@opindex mno-app-regs
@opindex mapp-regs
Specify @option{-mapp-regs} to generate output using the global registers
2 through 4, which the SPARC SVR4 ABI reserves for applications.  This
is the default.

To be fully SVR4 ABI compliant at the cost of some performance loss,
specify @option{-mno-app-regs}.  You should compile libraries and system
software with this option.

@item -mfpu
@itemx -mhard-float
@opindex mfpu
@opindex mhard-float
Generate output containing floating point instructions.  This is the
default.

@item -mno-fpu
@itemx -msoft-float
@opindex mno-fpu
@opindex msoft-float
Generate output containing library calls for floating point.
@strong{Warning:} the requisite libraries are not available for all SPARC
targets.  Normally the facilities of the machine's usual C compiler are
used, but this cannot be done directly in cross-compilation.  You must make
your own arrangements to provide suitable library functions for
cross-compilation.  The embedded targets @samp{sparc-*-aout} and
@samp{sparclite-*-*} do provide software floating point support.

@option{-msoft-float} changes the calling convention in the output file;
therefore, it is only useful if you compile @emph{all} of a program with
this option.  In particular, you need to compile @file{libgcc.a}, the
library that comes with GCC, with @option{-msoft-float} in order for
this to work.

@item -mhard-quad-float
@opindex mhard-quad-float
Generate output containing quad-word (long double) floating point
instructions.

@item -msoft-quad-float
@opindex msoft-quad-float
Generate output containing library calls for quad-word (long double)
floating point instructions.  The functions called are those specified
in the SPARC ABI@.  This is the default.

As of this writing, there are no sparc implementations that have hardware
support for the quad-word floating point instructions.  They all invoke
a trap handler for one of these instructions, and then the trap handler
emulates the effect of the instruction.  Because of the trap handler overhead,
this is much slower than calling the ABI library routines.  Thus the
@option{-msoft-quad-float} option is the default.

@item -mno-flat
@itemx -mflat
@opindex mno-flat
@opindex mflat
With @option{-mflat}, the compiler does not generate save/restore instructions
and will use a ``flat'' or single register window calling convention.
This model uses %i7 as the frame pointer and is compatible with the normal
register window model.  Code from either may be intermixed.
The local registers and the input registers (0--5) are still treated as
``call saved'' registers and will be saved on the stack as necessary.

With @option{-mno-flat} (the default), the compiler emits save/restore
instructions (except for leaf functions) and is the normal mode of operation.

@item -mno-unaligned-doubles
@itemx -munaligned-doubles
@opindex mno-unaligned-doubles
@opindex munaligned-doubles
Assume that doubles have 8 byte alignment.  This is the default.

With @option{-munaligned-doubles}, GCC assumes that doubles have 8 byte
alignment only if they are contained in another type, or if they have an
absolute address.  Otherwise, it assumes they have 4 byte alignment.
Specifying this option avoids some rare compatibility problems with code
generated by other compilers.  It is not the default because it results
in a performance loss, especially for floating point code.

@item -mno-faster-structs
@itemx -mfaster-structs
@opindex mno-faster-structs
@opindex mfaster-structs
With @option{-mfaster-structs}, the compiler assumes that structures
should have 8 byte alignment.  This enables the use of pairs of
@code{ldd} and @code{std} instructions for copies in structure
assignment, in place of twice as many @code{ld} and @code{st} pairs.
However, the use of this changed alignment directly violates the SPARC
ABI@.  Thus, it's intended only for use on targets where the developer
acknowledges that their resulting code will not be directly in line with
the rules of the ABI@.

@item -mv8
@itemx -msparclite
@opindex mv8
@opindex msparclite
These two options select variations on the SPARC architecture.

By default (unless specifically configured for the Fujitsu SPARClite),
GCC generates code for the v7 variant of the SPARC architecture.

@option{-mv8} will give you SPARC v8 code.  The only difference from v7
code is that the compiler emits the integer multiply and integer
divide instructions which exist in SPARC v8 but not in SPARC v7.

@option{-msparclite} will give you SPARClite code.  This adds the integer
multiply, integer divide step and scan (@code{ffs}) instructions which
exist in SPARClite but not in SPARC v7.

These options are deprecated and will be deleted in a future GCC release.
They have been replaced with @option{-mcpu=xxx}.

@item -mcypress
@itemx -msupersparc
@opindex mcypress
@opindex msupersparc
These two options select the processor for which the code is optimized.

With @option{-mcypress} (the default), the compiler optimizes code for the
Cypress CY7C602 chip, as used in the SPARCStation/SPARCServer 3xx series.
This is also appropriate for the older SPARCStation 1, 2, IPX etc.

With @option{-msupersparc} the compiler optimizes code for the SuperSPARC cpu, as
used in the SPARCStation 10, 1000 and 2000 series.  This flag also enables use
of the full SPARC v8 instruction set.

These options are deprecated and will be deleted in a future GCC release.
They have been replaced with @option{-mcpu=xxx}.

@item -mcpu=@var{cpu_type}
@opindex mcpu
Set the instruction set, register set, and instruction scheduling parameters
for machine type @var{cpu_type}.  Supported values for @var{cpu_type} are
@samp{v7}, @samp{cypress}, @samp{v8}, @samp{supersparc}, @samp{sparclite},
@samp{hypersparc}, @samp{sparclite86x}, @samp{f930}, @samp{f934},
@samp{sparclet}, @samp{tsc701}, @samp{v9}, @samp{ultrasparc}, and
@samp{ultrasparc3}.

Default instruction scheduling parameters are used for values that select
an architecture and not an implementation.  These are @samp{v7}, @samp{v8},
@samp{sparclite}, @samp{sparclet}, @samp{v9}.

Here is a list of each supported architecture and their supported
implementations.

@smallexample
    v7:             cypress
    v8:             supersparc, hypersparc
    sparclite:      f930, f934, sparclite86x
    sparclet:       tsc701
    v9:             ultrasparc, ultrasparc3
@end smallexample

@item -mtune=@var{cpu_type}
@opindex mtune
Set the instruction scheduling parameters for machine type
@var{cpu_type}, but do not set the instruction set or register set that the
option @option{-mcpu=@var{cpu_type}} would.

The same values for @option{-mcpu=@var{cpu_type}} can be used for
@option{-mtune=@var{cpu_type}}, but the only useful values are those
that select a particular cpu implementation.  Those are @samp{cypress},
@samp{supersparc}, @samp{hypersparc}, @samp{f930}, @samp{f934},
@samp{sparclite86x}, @samp{tsc701}, @samp{ultrasparc}, and
@samp{ultrasparc3}.

@end table

These @samp{-m} switches are supported in addition to the above
on the SPARCLET processor.

@table @gcctabopt
@item -mlittle-endian
@opindex mlittle-endian
Generate code for a processor running in little-endian mode.

@item -mlive-g0
@opindex mlive-g0
Treat register @code{%g0} as a normal register.
GCC will continue to clobber it as necessary but will not assume
it always reads as 0.

@item -mbroken-saverestore
@opindex mbroken-saverestore
Generate code that does not use non-trivial forms of the @code{save} and
@code{restore} instructions.  Early versions of the SPARCLET processor do
not correctly handle @code{save} and @code{restore} instructions used with
arguments.  They correctly handle them used without arguments.  A @code{save}
instruction used without arguments increments the current window pointer
but does not allocate a new stack frame.  It is assumed that the window
overflow trap handler will properly handle this case as will interrupt
handlers.
@end table

These @samp{-m} switches are supported in addition to the above
on SPARC V9 processors in 64-bit environments.

@table @gcctabopt
@item -mlittle-endian
@opindex mlittle-endian
Generate code for a processor running in little-endian mode.

@item -m32
@itemx -m64
@opindex m32
@opindex m64
Generate code for a 32-bit or 64-bit environment.
The 32-bit environment sets int, long and pointer to 32 bits.
The 64-bit environment sets int to 32 bits and long and pointer
to 64 bits.

@item -mcmodel=medlow
@opindex mcmodel=medlow
Generate code for the Medium/Low code model: the program must be linked
in the low 32 bits of the address space.  Pointers are 64 bits.
Programs can be statically or dynamically linked.

@item -mcmodel=medmid
@opindex mcmodel=medmid
Generate code for the Medium/Middle code model: the program must be linked
in the low 44 bits of the address space, the text segment must be less than
2G bytes, and data segment must be within 2G of the text segment.
Pointers are 64 bits.

@item -mcmodel=medany
@opindex mcmodel=medany
Generate code for the Medium/Anywhere code model: the program may be linked
anywhere in the address space, the text segment must be less than
2G bytes, and data segment must be within 2G of the text segment.
Pointers are 64 bits.

@item -mcmodel=embmedany
@opindex mcmodel=embmedany
Generate code for the Medium/Anywhere code model for embedded systems:
assume a 32-bit text and a 32-bit data segment, both starting anywhere
(determined at link time).  Register %g4 points to the base of the
data segment.  Pointers are still 64 bits.
Programs are statically linked, PIC is not supported.

@item -mstack-bias
@itemx -mno-stack-bias
@opindex mstack-bias
@opindex mno-stack-bias
With @option{-mstack-bias}, GCC assumes that the stack pointer, and
frame pointer if present, are offset by @minus{}2047 which must be added back
when making stack frame references.
Otherwise, assume no such offset is present.
@end table

@node ARM Options
@subsection ARM Options
@cindex ARM options

These @samp{-m} options are defined for Advanced RISC Machines (ARM)
architectures:

@table @gcctabopt
@item -mapcs-frame
@opindex mapcs-frame
Generate a stack frame that is compliant with the ARM Procedure Call
Standard for all functions, even if this is not strictly necessary for
correct execution of the code.  Specifying @option{-fomit-frame-pointer}
with this option will cause the stack frames not to be generated for
leaf functions.  The default is @option{-mno-apcs-frame}.

@item -mapcs
@opindex mapcs
This is a synonym for @option{-mapcs-frame}.

@item -mapcs-26
@opindex mapcs-26
Generate code for a processor running with a 26-bit program counter,
and conforming to the function calling standards for the APCS 26-bit
option.  This option replaces the @option{-m2} and @option{-m3} options
of previous releases of the compiler.

@item -mapcs-32
@opindex mapcs-32
Generate code for a processor running with a 32-bit program counter,
and conforming to the function calling standards for the APCS 32-bit
option.  This option replaces the @option{-m6} option of previous releases
of the compiler.

@ignore
@c not currently implemented
@item -mapcs-stack-check
@opindex mapcs-stack-check
Generate code to check the amount of stack space available upon entry to
every function (that actually uses some stack space).  If there is
insufficient space available then either the function
@samp{__rt_stkovf_split_small} or @samp{__rt_stkovf_split_big} will be
called, depending upon the amount of stack space required.  The run time
system is required to provide these functions.  The default is
@option{-mno-apcs-stack-check}, since this produces smaller code.

@c not currently implemented
@item -mapcs-float
@opindex mapcs-float
Pass floating point arguments using the float point registers.  This is
one of the variants of the APCS@.  This option is recommended if the
target hardware has a floating point unit or if a lot of floating point
arithmetic is going to be performed by the code.  The default is
@option{-mno-apcs-float}, since integer only code is slightly increased in
size if @option{-mapcs-float} is used.

@c not currently implemented
@item -mapcs-reentrant
@opindex mapcs-reentrant
Generate reentrant, position independent code.  The default is
@option{-mno-apcs-reentrant}.
@end ignore

@item -mthumb-interwork
@opindex mthumb-interwork
Generate code which supports calling between the ARM and Thumb
instruction sets.  Without this option the two instruction sets cannot
be reliably used inside one program.  The default is
@option{-mno-thumb-interwork}, since slightly larger code is generated
when @option{-mthumb-interwork} is specified.

@item -mno-sched-prolog
@opindex mno-sched-prolog
Prevent the reordering of instructions in the function prolog, or the
merging of those instruction with the instructions in the function's
body.  This means that all functions will start with a recognizable set
of instructions (or in fact one of a choice from a small set of
different function prologues), and this information can be used to
locate the start if functions inside an executable piece of code.  The
default is @option{-msched-prolog}.

@item -mhard-float
@opindex mhard-float
Generate output containing floating point instructions.  This is the
default.

@item -msoft-float
@opindex msoft-float
Generate output containing library calls for floating point.
@strong{Warning:} the requisite libraries are not available for all ARM
targets.  Normally the facilities of the machine's usual C compiler are
used, but this cannot be done directly in cross-compilation.  You must make
your own arrangements to provide suitable library functions for
cross-compilation.

@option{-msoft-float} changes the calling convention in the output file;
therefore, it is only useful if you compile @emph{all} of a program with
this option.  In particular, you need to compile @file{libgcc.a}, the
library that comes with GCC, with @option{-msoft-float} in order for
this to work.

@item -mlittle-endian
@opindex mlittle-endian
Generate code for a processor running in little-endian mode.  This is
the default for all standard configurations.

@item -mbig-endian
@opindex mbig-endian
Generate code for a processor running in big-endian mode; the default is
to compile code for a little-endian processor.

@item -mwords-little-endian
@opindex mwords-little-endian
This option only applies when generating code for big-endian processors.
Generate code for a little-endian word order but a big-endian byte
order.  That is, a byte order of the form @samp{32107654}.  Note: this
option should only be used if you require compatibility with code for
big-endian ARM processors generated by versions of the compiler prior to
2.8.

@item -malignment-traps
@opindex malignment-traps
Generate code that will not trap if the MMU has alignment traps enabled.
On ARM architectures prior to ARMv4, there were no instructions to
access half-word objects stored in memory.  However, when reading from
memory a feature of the ARM architecture allows a word load to be used,
even if the address is unaligned, and the processor core will rotate the
data as it is being loaded.  This option tells the compiler that such
misaligned accesses will cause a MMU trap and that it should instead
synthesize the access as a series of byte accesses.  The compiler can
still use word accesses to load half-word data if it knows that the
address is aligned to a word boundary.

This option is ignored when compiling for ARM architecture 4 or later,
since these processors have instructions to directly access half-word
objects in memory.

@item -mno-alignment-traps
@opindex mno-alignment-traps
Generate code that assumes that the MMU will not trap unaligned
accesses.  This produces better code when the target instruction set
does not have half-word memory operations (i.e.@: implementations prior to
ARMv4).

Note that you cannot use this option to access unaligned word objects,
since the processor will only fetch one 32-bit aligned object from
memory.

The default setting for most targets is @option{-mno-alignment-traps}, since
this produces better code when there are no half-word memory
instructions available.

@item -mshort-load-bytes
@itemx -mno-short-load-words
@opindex mshort-load-bytes
@opindex mno-short-load-words
These are deprecated aliases for @option{-malignment-traps}.

@item -mno-short-load-bytes
@itemx -mshort-load-words
@opindex mno-short-load-bytes
@opindex mshort-load-words
This are deprecated aliases for @option{-mno-alignment-traps}.

@item -mcpu=@var{name}
@opindex mcpu
This specifies the name of the target ARM processor.  GCC uses this name
to determine what kind of instructions it can emit when generating
assembly code.  Permissible names are: @samp{arm2}, @samp{arm250},
@samp{arm3}, @samp{arm6}, @samp{arm60}, @samp{arm600}, @samp{arm610},
@samp{arm620}, @samp{arm7}, @samp{arm7m}, @samp{arm7d}, @samp{arm7dm},
@samp{arm7di}, @samp{arm7dmi}, @samp{arm70}, @samp{arm700},
@samp{arm700i}, @samp{arm710}, @samp{arm710c}, @samp{arm7100},
@samp{arm7500}, @samp{arm7500fe}, @samp{arm7tdmi}, @samp{arm8},
@samp{strongarm}, @samp{strongarm110}, @samp{strongarm1100},
@samp{arm8}, @samp{arm810}, @samp{arm9}, @samp{arm9e}, @samp{arm920},
@samp{arm920t}, @samp{arm940t}, @samp{arm9tdmi}, @samp{arm10tdmi},
@samp{arm1020t}, @samp{xscale}, @samp{ep9312}.

@itemx -mtune=@var{name}
@opindex mtune
This option is very similar to the @option{-mcpu=} option, except that
instead of specifying the actual target processor type, and hence
restricting which instructions can be used, it specifies that GCC should
tune the performance of the code as if the target were of the type
specified in this option, but still choosing the instructions that it
will generate based on the cpu specified by a @option{-mcpu=} option.
For some ARM implementations better performance can be obtained by using
this option.

@item -march=@var{name}
@opindex march
This specifies the name of the target ARM architecture.  GCC uses this
name to determine what kind of instructions it can emit when generating
assembly code.  This option can be used in conjunction with or instead
of the @option{-mcpu=} option.  Permissible names are: @samp{armv2},
@samp{armv2a}, @samp{armv3}, @samp{armv3m}, @samp{armv4}, @samp{armv4t},
@samp{armv5}, @samp{armv5t}, @samp{armv5te}, @samp{ep9312}.

@item -mfpe=@var{number}
@itemx -mfp=@var{number}
@opindex mfpe
@opindex mfp
This specifies the version of the floating point emulation available on
the target.  Permissible values are 2 and 3.  @option{-mfp=} is a synonym
for @option{-mfpe=}, for compatibility with older versions of GCC@.

@item -mstructure-size-boundary=@var{n}
@opindex mstructure-size-boundary
The size of all structures and unions will be rounded up to a multiple
of the number of bits set by this option.  Permissible values are 8 and
32.  The default value varies for different toolchains.  For the COFF
targeted toolchain the default value is 8.  Specifying the larger number
can produce faster, more efficient code, but can also increase the size
of the program.  The two values are potentially incompatible.  Code
compiled with one value cannot necessarily expect to work with code or
libraries compiled with the other value, if they exchange information
using structures or unions.

@item -mabort-on-noreturn
@opindex mabort-on-noreturn
Generate a call to the function @code{abort} at the end of a
@code{noreturn} function.  It will be executed if the function tries to
return.

@item -mlong-calls
@itemx -mno-long-calls
@opindex mlong-calls
@opindex mno-long-calls
Tells the compiler to perform function calls by first loading the
address of the function into a register and then performing a subroutine
call on this register.  This switch is needed if the target function
will lie outside of the 64 megabyte addressing range of the offset based
version of subroutine call instruction.

Even if this switch is enabled, not all function calls will be turned
into long calls.  The heuristic is that static functions, functions
which have the @samp{short-call} attribute, functions that are inside
the scope of a @samp{#pragma no_long_calls} directive and functions whose
definitions have already been compiled within the current compilation
unit, will not be turned into long calls.  The exception to this rule is
that weak function definitions, functions with the @samp{long-call}
attribute or the @samp{section} attribute, and functions that are within
the scope of a @samp{#pragma long_calls} directive, will always be
turned into long calls.

This feature is not enabled by default.  Specifying
@option{-mno-long-calls} will restore the default behavior, as will
placing the function calls within the scope of a @samp{#pragma
long_calls_off} directive.  Note these switches have no effect on how
the compiler generates code to handle function calls via function
pointers.

@item -mnop-fun-dllimport
@opindex mnop-fun-dllimport
Disable support for the @code{dllimport} attribute.

@item -msingle-pic-base
@opindex msingle-pic-base
Treat the register used for PIC addressing as read-only, rather than
loading it in the prologue for each function.  The run-time system is
responsible for initializing this register with an appropriate value
before execution begins.

@item -mpic-register=@var{reg}
@opindex mpic-register
Specify the register to be used for PIC addressing.  The default is R10
unless stack-checking is enabled, when R9 is used.

@item -mcirrus-fix-invalid-insns
@opindex -mcirrus-fix-invalid-insns
@opindex -mno-cirrus-fix-invalid-insns
Insert NOPs into the instruction stream to in order to work around
problems with invalid Maverick instruction combinations.  This option
is only valid if the @option{-mcpu=ep9312} option has been used to
enable generation of instructions for the Cirrus Maverick floating
point co-processor.  This option is not enabled by default, since the
problem is only present in older Maverick implementations.  The default
can be re-enabled by use of the @option{-mno-cirrus-fix-invalid-insns}
switch.

@item -mpoke-function-name
@opindex mpoke-function-name
Write the name of each function into the text section, directly
preceding the function prologue.  The generated code is similar to this:

@smallexample
     t0
         .ascii "arm_poke_function_name", 0
         .align
     t1
         .word 0xff000000 + (t1 - t0)
     arm_poke_function_name
         mov     ip, sp
         stmfd   sp!, @{fp, ip, lr, pc@}
         sub     fp, ip, #4
@end smallexample

When performing a stack backtrace, code can inspect the value of
@code{pc} stored at @code{fp + 0}.  If the trace function then looks at
location @code{pc - 12} and the top 8 bits are set, then we know that
there is a function name embedded immediately preceding this location
and has length @code{((pc[-3]) & 0xff000000)}.

@item -mthumb
@opindex mthumb
Generate code for the 16-bit Thumb instruction set.  The default is to
use the 32-bit ARM instruction set.

@item -mtpcs-frame
@opindex mtpcs-frame
Generate a stack frame that is compliant with the Thumb Procedure Call
Standard for all non-leaf functions.  (A leaf function is one that does
not call any other functions.)  The default is @option{-mno-tpcs-frame}.

@item -mtpcs-leaf-frame
@opindex mtpcs-leaf-frame
Generate a stack frame that is compliant with the Thumb Procedure Call
Standard for all leaf functions.  (A leaf function is one that does
not call any other functions.)  The default is @option{-mno-apcs-leaf-frame}.

@item -mcallee-super-interworking
@opindex mcallee-super-interworking
Gives all externally visible functions in the file being compiled an ARM
instruction set header which switches to Thumb mode before executing the
rest of the function.  This allows these functions to be called from
non-interworking code.

@item -mcaller-super-interworking
@opindex mcaller-super-interworking
Allows calls via function pointers (including virtual functions) to
execute correctly regardless of whether the target code has been
compiled for interworking or not.  There is a small overhead in the cost
of executing a function pointer if this option is enabled.

@end table

@node MN10200 Options
@subsection MN10200 Options
@cindex MN10200 options

These @option{-m} options are defined for Matsushita MN10200 architectures:
@table @gcctabopt

@item -mrelax
@opindex mrelax
Indicate to the linker that it should perform a relaxation optimization pass
to shorten branches, calls and absolute memory addresses.  This option only
has an effect when used on the command line for the final link step.

This option makes symbolic debugging impossible.
@end table

@node MN10300 Options
@subsection MN10300 Options
@cindex MN10300 options

These @option{-m} options are defined for Matsushita MN10300 architectures:

@table @gcctabopt
@item -mmult-bug
@opindex mmult-bug
Generate code to avoid bugs in the multiply instructions for the MN10300
processors.  This is the default.

@item -mno-mult-bug
@opindex mno-mult-bug
Do not generate code to avoid bugs in the multiply instructions for the
MN10300 processors.

@item -mam33
@opindex mam33
Generate code which uses features specific to the AM33 processor.

@item -mno-am33
@opindex mno-am33
Do not generate code which uses features specific to the AM33 processor.  This
is the default.

@item -mno-crt0
@opindex mno-crt0
Do not link in the C run-time initialization object file.

@item -mrelax
@opindex mrelax
Indicate to the linker that it should perform a relaxation optimization pass
to shorten branches, calls and absolute memory addresses.  This option only
has an effect when used on the command line for the final link step.

This option makes symbolic debugging impossible.
@end table


@node M32R/D Options
@subsection M32R/D Options
@cindex M32R/D options

These @option{-m} options are defined for Mitsubishi M32R/D architectures:

@table @gcctabopt
@item -m32rx
@opindex m32rx
Generate code for the M32R/X@.

@item -m32r
@opindex m32r
Generate code for the M32R@.  This is the default.

@item -mcode-model=small
@opindex mcode-model=small
Assume all objects live in the lower 16MB of memory (so that their addresses
can be loaded with the @code{ld24} instruction), and assume all subroutines
are reachable with the @code{bl} instruction.
This is the default.

The addressability of a particular object can be set with the
@code{model} attribute.

@item -mcode-model=medium
@opindex mcode-model=medium
Assume objects may be anywhere in the 32-bit address space (the compiler
will generate @code{seth/add3} instructions to load their addresses), and
assume all subroutines are reachable with the @code{bl} instruction.

@item -mcode-model=large
@opindex mcode-model=large
Assume objects may be anywhere in the 32-bit address space (the compiler
will generate @code{seth/add3} instructions to load their addresses), and
assume subroutines may not be reachable with the @code{bl} instruction
(the compiler will generate the much slower @code{seth/add3/jl}
instruction sequence).

@item -msdata=none
@opindex msdata=none
Disable use of the small data area.  Variables will be put into
one of @samp{.data}, @samp{bss}, or @samp{.rodata} (unless the
@code{section} attribute has been specified).
This is the default.

The small data area consists of sections @samp{.sdata} and @samp{.sbss}.
Objects may be explicitly put in the small data area with the
@code{section} attribute using one of these sections.

@item -msdata=sdata
@opindex msdata=sdata
Put small global and static data in the small data area, but do not
generate special code to reference them.

@item -msdata=use
@opindex msdata=use
Put small global and static data in the small data area, and generate
special instructions to reference them.

@item -G @var{num}
@opindex G
@cindex smaller data references
Put global and static objects less than or equal to @var{num} bytes
into the small data or bss sections instead of the normal data or bss
sections.  The default value of @var{num} is 8.
The @option{-msdata} option must be set to one of @samp{sdata} or @samp{use}
for this option to have any effect.

All modules should be compiled with the same @option{-G @var{num}} value.
Compiling with different values of @var{num} may or may not work; if it
doesn't the linker will give an error message---incorrect code will not be
generated.

@end table

@node M88K Options
@subsection M88K Options
@cindex M88k options

These @samp{-m} options are defined for Motorola 88k architectures:

@table @gcctabopt
@item -m88000
@opindex m88000
Generate code that works well on both the m88100 and the
m88110.

@item -m88100
@opindex m88100
Generate code that works best for the m88100, but that also
runs on the m88110.

@item -m88110
@opindex m88110
Generate code that works best for the m88110, and may not run
on the m88100.

@item -mbig-pic
@opindex mbig-pic
Obsolete option to be removed from the next revision.
Use @option{-fPIC}.

@item -midentify-revision
@opindex midentify-revision
@cindex identifying source, compiler (88k)
Include an @code{ident} directive in the assembler output recording the
source file name, compiler name and version, timestamp, and compilation
flags used.

@item -mno-underscores
@opindex mno-underscores
@cindex underscores, avoiding (88k)
In assembler output, emit symbol names without adding an underscore
character at the beginning of each name.  The default is to use an
underscore as prefix on each name.

@item -mocs-debug-info
@itemx -mno-ocs-debug-info
@opindex mocs-debug-info
@opindex mno-ocs-debug-info
@cindex OCS (88k)
@cindex debugging, 88k OCS
Include (or omit) additional debugging information (about registers used
in each stack frame) as specified in the 88open Object Compatibility
Standard, ``OCS''@.  This extra information allows debugging of code that
has had the frame pointer eliminated.  The default for SVr4 and Delta 88
SVr3.2 is to include this information; other 88k configurations omit this
information by default.

@item -mocs-frame-position
@opindex mocs-frame-position
@cindex register positions in frame (88k)
When emitting COFF debugging information for automatic variables and
parameters stored on the stack, use the offset from the canonical frame
address, which is the stack pointer (register 31) on entry to the
function.  The SVr4 and Delta88 SVr3.2, and BCS configurations use
@option{-mocs-frame-position}; other 88k configurations have the default
@option{-mno-ocs-frame-position}.

@item -mno-ocs-frame-position
@opindex mno-ocs-frame-position
@cindex register positions in frame (88k)
When emitting COFF debugging information for automatic variables and
parameters stored on the stack, use the offset from the frame pointer
register (register 30).  When this option is in effect, the frame
pointer is not eliminated when debugging information is selected by the
-g switch.

@item -moptimize-arg-area
@opindex moptimize-arg-area
@cindex arguments in frame (88k)
Save space by reorganizing the stack frame.  This option generates code
that does not agree with the 88open specifications, but uses less
memory.

@itemx -mno-optimize-arg-area
@opindex mno-optimize-arg-area
Do not reorganize the stack frame to save space.  This is the default.
The generated conforms to the specification, but uses more memory.

@item -mshort-data-@var{num}
@opindex mshort-data
@cindex smaller data references (88k)
@cindex r0-relative references (88k)
Generate smaller data references by making them relative to @code{r0},
which allows loading a value using a single instruction (rather than the
usual two).  You control which data references are affected by
specifying @var{num} with this option.  For example, if you specify
@option{-mshort-data-512}, then the data references affected are those
involving displacements of less than 512 bytes.
@option{-mshort-data-@var{num}} is not effective for @var{num} greater
than 64k.

@item -mserialize-volatile
@opindex mserialize-volatile
@itemx -mno-serialize-volatile
@opindex mno-serialize-volatile
@cindex sequential consistency on 88k
Do, or don't, generate code to guarantee sequential consistency
of volatile memory references.  By default, consistency is
guaranteed.

The order of memory references made by the MC88110 processor does
not always match the order of the instructions requesting those
references.  In particular, a load instruction may execute before
a preceding store instruction.  Such reordering violates
sequential consistency of volatile memory references, when there
are multiple processors.   When consistency must be guaranteed,
GCC generates special instructions, as needed, to force
execution in the proper order.

The MC88100 processor does not reorder memory references and so
always provides sequential consistency.  However, by default, GCC
generates the special instructions to guarantee consistency
even when you use @option{-m88100}, so that the code may be run on an
MC88110 processor.  If you intend to run your code only on the
MC88100 processor, you may use @option{-mno-serialize-volatile}.

The extra code generated to guarantee consistency may affect the
performance of your application.  If you know that you can safely
forgo this guarantee, you may use @option{-mno-serialize-volatile}.

@item -msvr4
@itemx -msvr3
@opindex msvr4
@opindex msvr3
@cindex assembler syntax, 88k
@cindex SVr4
Turn on (@option{-msvr4}) or off (@option{-msvr3}) compiler extensions
related to System V release 4 (SVr4).  This controls the following:

@enumerate
@item
Which variant of the assembler syntax to emit.
@item
@option{-msvr4} makes the C preprocessor recognize @samp{#pragma weak}
that is used on System V release 4.
@item
@option{-msvr4} makes GCC issue additional declaration directives used in
SVr4.
@end enumerate

@option{-msvr4} is the default for the m88k-motorola-sysv4 configuration.
@option{-msvr3} is the default for all other m88k configurations.

@item -mversion-03.00
@opindex mversion-03.00
This option is obsolete, and is ignored.
@c ??? which asm syntax better for GAS?  option there too?

@item -mno-check-zero-division
@itemx -mcheck-zero-division
@opindex mno-check-zero-division
@opindex mcheck-zero-division
@cindex zero division on 88k
Do, or don't, generate code to guarantee that integer division by
zero will be detected.  By default, detection is guaranteed.

Some models of the MC88100 processor fail to trap upon integer
division by zero under certain conditions.  By default, when
compiling code that might be run on such a processor, GCC
generates code that explicitly checks for zero-valued divisors
and traps with exception number 503 when one is detected.  Use of
@option{-mno-check-zero-division} suppresses such checking for code
generated to run on an MC88100 processor.

GCC assumes that the MC88110 processor correctly detects all instances
of integer division by zero.  When @option{-m88110} is specified, no
explicit checks for zero-valued divisors are generated, and both
@option{-mcheck-zero-division} and @option{-mno-check-zero-division} are
ignored.

@item -muse-div-instruction
@opindex muse-div-instruction
@cindex divide instruction, 88k
Use the div instruction for signed integer division on the
MC88100 processor.  By default, the div instruction is not used.

On the MC88100 processor the signed integer division instruction
div) traps to the operating system on a negative operand.  The
operating system transparently completes the operation, but at a
large cost in execution time.  By default, when compiling code
that might be run on an MC88100 processor, GCC emulates signed
integer division using the unsigned integer division instruction
divu), thereby avoiding the large penalty of a trap to the
operating system.  Such emulation has its own, smaller, execution
cost in both time and space.  To the extent that your code's
important signed integer division operations are performed on two
nonnegative operands, it may be desirable to use the div
instruction directly.

On the MC88110 processor the div instruction (also known as the
divs instruction) processes negative operands without trapping to
the operating system.  When @option{-m88110} is specified,
@option{-muse-div-instruction} is ignored, and the div instruction is used
for signed integer division.

Note that the result of dividing @code{INT_MIN} by @minus{}1 is undefined.  In
particular, the behavior of such a division with and without
@option{-muse-div-instruction} may differ.

@item -mtrap-large-shift
@itemx -mhandle-large-shift
@opindex mtrap-large-shift
@opindex mhandle-large-shift
@cindex bit shift overflow (88k)
@cindex large bit shifts (88k)
Include code to detect bit-shifts of more than 31 bits; respectively,
trap such shifts or emit code to handle them properly.  By default GCC
makes no special provision for large bit shifts.

@item -mwarn-passed-structs
@opindex mwarn-passed-structs
@cindex structure passing (88k)
Warn when a function passes a struct as an argument or result.
Structure-passing conventions have changed during the evolution of the C
language, and are often the source of portability problems.  By default,
GCC issues no such warning.
@end table

@c break page here to avoid unsightly interparagraph stretch.
@c -zw, 2001-8-17
@page

@node RS/6000 and PowerPC Options
@subsection IBM RS/6000 and PowerPC Options
@cindex RS/6000 and PowerPC Options
@cindex IBM RS/6000 and PowerPC Options

These @samp{-m} options are defined for the IBM RS/6000 and PowerPC:
@table @gcctabopt
@item -mpower
@itemx -mno-power
@itemx -mpower2
@itemx -mno-power2
@itemx -mpowerpc
@itemx -mno-powerpc
@itemx -mpowerpc-gpopt
@itemx -mno-powerpc-gpopt
@itemx -mpowerpc-gfxopt
@itemx -mno-powerpc-gfxopt
@itemx -mpowerpc64
@itemx -mno-powerpc64
@opindex mpower
@opindex mno-power
@opindex mpower2
@opindex mno-power2
@opindex mpowerpc
@opindex mno-powerpc
@opindex mpowerpc-gpopt
@opindex mno-powerpc-gpopt
@opindex mpowerpc-gfxopt
@opindex mno-powerpc-gfxopt
@opindex mpowerpc64
@opindex mno-powerpc64
GCC supports two related instruction set architectures for the
RS/6000 and PowerPC@.  The @dfn{POWER} instruction set are those
instructions supported by the @samp{rios} chip set used in the original
RS/6000 systems and the @dfn{PowerPC} instruction set is the
architecture of the Motorola MPC5xx, MPC6xx, MPC8xx microprocessors, and
the IBM 4xx microprocessors.

Neither architecture is a subset of the other.  However there is a
large common subset of instructions supported by both.  An MQ
register is included in processors supporting the POWER architecture.

You use these options to specify which instructions are available on the
processor you are using.  The default value of these options is
determined when configuring GCC@.  Specifying the
@option{-mcpu=@var{cpu_type}} overrides the specification of these
options.  We recommend you use the @option{-mcpu=@var{cpu_type}} option
rather than the options listed above.

The @option{-mpower} option allows GCC to generate instructions that
are found only in the POWER architecture and to use the MQ register.
Specifying @option{-mpower2} implies @option{-power} and also allows GCC
to generate instructions that are present in the POWER2 architecture but
not the original POWER architecture.

The @option{-mpowerpc} option allows GCC to generate instructions that
are found only in the 32-bit subset of the PowerPC architecture.
Specifying @option{-mpowerpc-gpopt} implies @option{-mpowerpc} and also allows
GCC to use the optional PowerPC architecture instructions in the
General Purpose group, including floating-point square root.  Specifying
@option{-mpowerpc-gfxopt} implies @option{-mpowerpc} and also allows GCC to
use the optional PowerPC architecture instructions in the Graphics
group, including floating-point select.

The @option{-mpowerpc64} option allows GCC to generate the additional
64-bit instructions that are found in the full PowerPC64 architecture
and to treat GPRs as 64-bit, doubleword quantities.  GCC defaults to
@option{-mno-powerpc64}.

If you specify both @option{-mno-power} and @option{-mno-powerpc}, GCC
will use only the instructions in the common subset of both
architectures plus some special AIX common-mode calls, and will not use
the MQ register.  Specifying both @option{-mpower} and @option{-mpowerpc}
permits GCC to use any instruction from either architecture and to
allow use of the MQ register; specify this for the Motorola MPC601.

@item -mnew-mnemonics
@itemx -mold-mnemonics
@opindex mnew-mnemonics
@opindex mold-mnemonics
Select which mnemonics to use in the generated assembler code.  With
@option{-mnew-mnemonics}, GCC uses the assembler mnemonics defined for
the PowerPC architecture.  With @option{-mold-mnemonics} it uses the
assembler mnemonics defined for the POWER architecture.  Instructions
defined in only one architecture have only one mnemonic; GCC uses that
mnemonic irrespective of which of these options is specified.

GCC defaults to the mnemonics appropriate for the architecture in
use.  Specifying @option{-mcpu=@var{cpu_type}} sometimes overrides the
value of these option.  Unless you are building a cross-compiler, you
should normally not specify either @option{-mnew-mnemonics} or
@option{-mold-mnemonics}, but should instead accept the default.

@item -mcpu=@var{cpu_type}
@opindex mcpu
Set architecture type, register usage, choice of mnemonics, and
instruction scheduling parameters for machine type @var{cpu_type}.
Supported values for @var{cpu_type} are @samp{rios}, @samp{rios1},
@samp{rsc}, @samp{rios2}, @samp{rs64a}, @samp{601}, @samp{602},
@samp{603}, @samp{603e}, @samp{604}, @samp{604e}, @samp{620},
@samp{630}, @samp{740}, @samp{7400}, @samp{7450}, @samp{750},
@samp{power}, @samp{power2}, @samp{powerpc}, @samp{403}, @samp{505},
@samp{801}, @samp{821}, @samp{823}, and @samp{860} and @samp{common}.

@option{-mcpu=common} selects a completely generic processor.  Code
generated under this option will run on any POWER or PowerPC processor.
GCC will use only the instructions in the common subset of both
architectures, and will not use the MQ register.  GCC assumes a generic
processor model for scheduling purposes.

@option{-mcpu=power}, @option{-mcpu=power2}, @option{-mcpu=powerpc}, and
@option{-mcpu=powerpc64} specify generic POWER, POWER2, pure 32-bit
PowerPC (i.e., not MPC601), and 64-bit PowerPC architecture machine
types, with an appropriate, generic processor model assumed for
scheduling purposes.

The other options specify a specific processor.  Code generated under
those options will run best on that processor, and may not run at all on
others.

The @option{-mcpu} options automatically enable or disable other
@option{-m} options as follows:

@table @samp
@item common
@option{-mno-power}, @option{-mno-powerpc}

@item power
@itemx power2
@itemx rios1
@itemx rios2
@itemx rsc
@option{-mpower}, @option{-mno-powerpc}, @option{-mno-new-mnemonics}

@item powerpc
@itemx rs64a
@itemx 602
@itemx 603
@itemx 603e
@itemx 604
@itemx 620
@itemx 630
@itemx 740
@itemx 7400
@itemx 7450
@itemx 750
@itemx 505
@option{-mno-power}, @option{-mpowerpc}, @option{-mnew-mnemonics}

@item 601
@option{-mpower}, @option{-mpowerpc}, @option{-mnew-mnemonics}

@item 403
@itemx 821
@itemx 860
@option{-mno-power}, @option{-mpowerpc}, @option{-mnew-mnemonics}, @option{-msoft-float}
@end table

@item -mtune=@var{cpu_type}
@opindex mtune
Set the instruction scheduling parameters for machine type
@var{cpu_type}, but do not set the architecture type, register usage, or
choice of mnemonics, as @option{-mcpu=@var{cpu_type}} would.  The same
values for @var{cpu_type} are used for @option{-mtune} as for
@option{-mcpu}.  If both are specified, the code generated will use the
architecture, registers, and mnemonics set by @option{-mcpu}, but the
scheduling parameters set by @option{-mtune}.

@item -maltivec
@itemx -mno-altivec
@opindex maltivec
@opindex mno-altivec
These switches enable or disable the use of built-in functions that
allow access to the AltiVec instruction set.  You may also need to set
@option{-mabi=altivec} to adjust the current ABI with AltiVec ABI
enhancements.

@item -mabi=spe
@opindex mabi=spe
Extend the current ABI with SPE ABI extensions.  This does not change
the default ABI, instead it adds the SPE ABI extensions to the current
ABI@.

@item -mabi=no-spe
@opindex mabi=no-spe
Disable Booke SPE ABI extensions for the current ABI.

@item -misel=@var{yes/no}
@itemx -misel
@opindex misel
This switch enables or disables the generation of ISEL instructions.

@item -mspe=@var{yes/no}
@itemx -mspe
@opindex mspe
This switch enables or disables the generation of SPE simd
instructions.

@item -mfloat-gprs=@var{yes/no}
@itemx -mfloat-gprs
@opindex mfloat-gprs
This switch enables or disables the generation of floating point
operations on the general purpose registers for architectures that
support it.  This option is currently only available on the MPC8540.

@item -mfull-toc
@itemx -mno-fp-in-toc
@itemx -mno-sum-in-toc
@itemx -mminimal-toc
@opindex mfull-toc
@opindex mno-fp-in-toc
@opindex mno-sum-in-toc
@opindex mminimal-toc
Modify generation of the TOC (Table Of Contents), which is created for
every executable file.  The @option{-mfull-toc} option is selected by
default.  In that case, GCC will allocate at least one TOC entry for
each unique non-automatic variable reference in your program.  GCC
will also place floating-point constants in the TOC@.  However, only
16,384 entries are available in the TOC@.

If you receive a linker error message that saying you have overflowed
the available TOC space, you can reduce the amount of TOC space used
with the @option{-mno-fp-in-toc} and @option{-mno-sum-in-toc} options.
@option{-mno-fp-in-toc} prevents GCC from putting floating-point
constants in the TOC and @option{-mno-sum-in-toc} forces GCC to
generate code to calculate the sum of an address and a constant at
run-time instead of putting that sum into the TOC@.  You may specify one
or both of these options.  Each causes GCC to produce very slightly
slower and larger code at the expense of conserving TOC space.

If you still run out of space in the TOC even when you specify both of
these options, specify @option{-mminimal-toc} instead.  This option causes
GCC to make only one TOC entry for every file.  When you specify this
option, GCC will produce code that is slower and larger but which
uses extremely little TOC space.  You may wish to use this option
only on files that contain less frequently executed code.

@item -maix64
@itemx -maix32
@opindex maix64
@opindex maix32
Enable 64-bit AIX ABI and calling convention: 64-bit pointers, 64-bit
@code{long} type, and the infrastructure needed to support them.
Specifying @option{-maix64} implies @option{-mpowerpc64} and
@option{-mpowerpc}, while @option{-maix32} disables the 64-bit ABI and
implies @option{-mno-powerpc64}.  GCC defaults to @option{-maix32}.

@item -mxl-call
@itemx -mno-xl-call
@opindex mxl-call
@opindex mno-xl-call
On AIX, pass floating-point arguments to prototyped functions beyond the
register save area (RSA) on the stack in addition to argument FPRs.  The
AIX calling convention was extended but not initially documented to
handle an obscure K&R C case of calling a function that takes the
address of its arguments with fewer arguments than declared.  AIX XL
compilers access floating point arguments which do not fit in the
RSA from the stack when a subroutine is compiled without
optimization.  Because always storing floating-point arguments on the
stack is inefficient and rarely needed, this option is not enabled by
default and only is necessary when calling subroutines compiled by AIX
XL compilers without optimization.

@item -mpe
@opindex mpe
Support @dfn{IBM RS/6000 SP} @dfn{Parallel Environment} (PE)@.  Link an
application written to use message passing with special startup code to
enable the application to run.  The system must have PE installed in the
standard location (@file{/usr/lpp/ppe.poe/}), or the @file{specs} file
must be overridden with the @option{-specs=} option to specify the
appropriate directory location.  The Parallel Environment does not
support threads, so the @option{-mpe} option and the @option{-pthread}
option are incompatible.

@item -malign-natural
@itemx -malign-power
@opindex malign-natural
@opindex malign-power
On AIX, Darwin, and 64-bit PowerPC Linux, the option
@option{-malign-natural} overrides the ABI-defined alignment of larger
types, such as floating-point doubles, on their natural size-based boundary.
The option @option{-malign-power} instructs GCC to follow the ABI-specified
alignment rules.  GCC defaults to the standard alignment defined in the ABI.

@item -msoft-float
@itemx -mhard-float
@opindex msoft-float
@opindex mhard-float
Generate code that does not use (uses) the floating-point register set.
Software floating point emulation is provided if you use the
@option{-msoft-float} option, and pass the option to GCC when linking.

@item -mmultiple
@itemx -mno-multiple
@opindex mmultiple
@opindex mno-multiple
Generate code that uses (does not use) the load multiple word
instructions and the store multiple word instructions.  These
instructions are generated by default on POWER systems, and not
generated on PowerPC systems.  Do not use @option{-mmultiple} on little
endian PowerPC systems, since those instructions do not work when the
processor is in little endian mode.  The exceptions are PPC740 and
PPC750 which permit the instructions usage in little endian mode.

@item -mstring
@itemx -mno-string
@opindex mstring
@opindex mno-string
Generate code that uses (does not use) the load string instructions
and the store string word instructions to save multiple registers and
do small block moves.  These instructions are generated by default on
POWER systems, and not generated on PowerPC systems.  Do not use
@option{-mstring} on little endian PowerPC systems, since those
instructions do not work when the processor is in little endian mode.
The exceptions are PPC740 and PPC750 which permit the instructions
usage in little endian mode.

@item -mupdate
@itemx -mno-update
@opindex mupdate
@opindex mno-update
Generate code that uses (does not use) the load or store instructions
that update the base register to the address of the calculated memory
location.  These instructions are generated by default.  If you use
@option{-mno-update}, there is a small window between the time that the
stack pointer is updated and the address of the previous frame is
stored, which means code that walks the stack frame across interrupts or
signals may get corrupted data.

@item -mfused-madd
@itemx -mno-fused-madd
@opindex mfused-madd
@opindex mno-fused-madd
Generate code that uses (does not use) the floating point multiply and
accumulate instructions.  These instructions are generated by default if
hardware floating is used.

@item -mno-bit-align
@itemx -mbit-align
@opindex mno-bit-align
@opindex mbit-align
On System V.4 and embedded PowerPC systems do not (do) force structures
and unions that contain bit-fields to be aligned to the base type of the
bit-field.

For example, by default a structure containing nothing but 8
@code{unsigned} bit-fields of length 1 would be aligned to a 4 byte
boundary and have a size of 4 bytes.  By using @option{-mno-bit-align},
the structure would be aligned to a 1 byte boundary and be one byte in
size.

@item -mno-strict-align
@itemx -mstrict-align
@opindex mno-strict-align
@opindex mstrict-align
On System V.4 and embedded PowerPC systems do not (do) assume that
unaligned memory references will be handled by the system.

@item -mrelocatable
@itemx -mno-relocatable
@opindex mrelocatable
@opindex mno-relocatable
On embedded PowerPC systems generate code that allows (does not allow)
the program to be relocated to a different address at runtime.  If you
use @option{-mrelocatable} on any module, all objects linked together must
be compiled with @option{-mrelocatable} or @option{-mrelocatable-lib}.

@item -mrelocatable-lib
@itemx -mno-relocatable-lib
@opindex mrelocatable-lib
@opindex mno-relocatable-lib
On embedded PowerPC systems generate code that allows (does not allow)
the program to be relocated to a different address at runtime.  Modules
compiled with @option{-mrelocatable-lib} can be linked with either modules
compiled without @option{-mrelocatable} and @option{-mrelocatable-lib} or
with modules compiled with the @option{-mrelocatable} options.

@item -mno-toc
@itemx -mtoc
@opindex mno-toc
@opindex mtoc
On System V.4 and embedded PowerPC systems do not (do) assume that
register 2 contains a pointer to a global area pointing to the addresses
used in the program.

@item -mlittle
@itemx -mlittle-endian
@opindex mlittle
@opindex mlittle-endian
On System V.4 and embedded PowerPC systems compile code for the
processor in little endian mode.  The @option{-mlittle-endian} option is
the same as @option{-mlittle}.

@item -mbig
@itemx -mbig-endian
@opindex mbig
@opindex mbig-endian
On System V.4 and embedded PowerPC systems compile code for the
processor in big endian mode.  The @option{-mbig-endian} option is
the same as @option{-mbig}.

@item -mdynamic-no-pic
@opindex mdynamic-no-pic
On Darwin and Mac OS X systems, compile code so that it is not
relocatable, but that its external references are relocatable.  The
resulting code is suitable for applications, but not shared
libraries.

@item -mcall-sysv
@opindex mcall-sysv
On System V.4 and embedded PowerPC systems compile code using calling
conventions that adheres to the March 1995 draft of the System V
Application Binary Interface, PowerPC processor supplement.  This is the
default unless you configured GCC using @samp{powerpc-*-eabiaix}.

@item -mcall-sysv-eabi
@opindex mcall-sysv-eabi
Specify both @option{-mcall-sysv} and @option{-meabi} options.

@item -mcall-sysv-noeabi
@opindex mcall-sysv-noeabi
Specify both @option{-mcall-sysv} and @option{-mno-eabi} options.

@item -mcall-solaris
@opindex mcall-solaris
On System V.4 and embedded PowerPC systems compile code for the Solaris
operating system.

@item -mcall-linux
@opindex mcall-linux
On System V.4 and embedded PowerPC systems compile code for the
Linux-based GNU system.

@item -mcall-gnu
@opindex mcall-gnu
On System V.4 and embedded PowerPC systems compile code for the
Hurd-based GNU system.

@item -mcall-netbsd
@opindex mcall-netbsd
On System V.4 and embedded PowerPC systems compile code for the
NetBSD operating system.

@item -maix-struct-return
@opindex maix-struct-return
Return all structures in memory (as specified by the AIX ABI)@.

@item -msvr4-struct-return
@opindex msvr4-struct-return
Return structures smaller than 8 bytes in registers (as specified by the
SVR4 ABI)@.

@item -mabi=altivec
@opindex mabi=altivec
Extend the current ABI with AltiVec ABI extensions.  This does not
change the default ABI, instead it adds the AltiVec ABI extensions to
the current ABI@.

@item -mabi=no-altivec
@opindex mabi=no-altivec
Disable AltiVec ABI extensions for the current ABI.

@item -mprototype
@itemx -mno-prototype
@opindex mprototype
@opindex mno-prototype
On System V.4 and embedded PowerPC systems assume that all calls to
variable argument functions are properly prototyped.  Otherwise, the
compiler must insert an instruction before every non prototyped call to
set or clear bit 6 of the condition code register (@var{CR}) to
indicate whether floating point values were passed in the floating point
registers in case the function takes a variable arguments.  With
@option{-mprototype}, only calls to prototyped variable argument functions
will set or clear the bit.

@item -msim
@opindex msim
On embedded PowerPC systems, assume that the startup module is called
@file{sim-crt0.o} and that the standard C libraries are @file{libsim.a} and
@file{libc.a}.  This is the default for @samp{powerpc-*-eabisim}.
configurations.

@item -mmvme
@opindex mmvme
On embedded PowerPC systems, assume that the startup module is called
@file{crt0.o} and the standard C libraries are @file{libmvme.a} and
@file{libc.a}.

@item -mads
@opindex mads
On embedded PowerPC systems, assume that the startup module is called
@file{crt0.o} and the standard C libraries are @file{libads.a} and
@file{libc.a}.

@item -myellowknife
@opindex myellowknife
On embedded PowerPC systems, assume that the startup module is called
@file{crt0.o} and the standard C libraries are @file{libyk.a} and
@file{libc.a}.

@item -mvxworks
@opindex mvxworks
On System V.4 and embedded PowerPC systems, specify that you are
compiling for a VxWorks system.

@item -mwindiss
@opindex mwindiss
Specify that you are compiling for the WindISS simulation environment.

@item -memb
@opindex memb
On embedded PowerPC systems, set the @var{PPC_EMB} bit in the ELF flags
header to indicate that @samp{eabi} extended relocations are used.

@item -meabi
@itemx -mno-eabi
@opindex meabi
@opindex mno-eabi
On System V.4 and embedded PowerPC systems do (do not) adhere to the
Embedded Applications Binary Interface (eabi) which is a set of
modifications to the System V.4 specifications.  Selecting @option{-meabi}
means that the stack is aligned to an 8 byte boundary, a function
@code{__eabi} is called to from @code{main} to set up the eabi
environment, and the @option{-msdata} option can use both @code{r2} and
@code{r13} to point to two separate small data areas.  Selecting
@option{-mno-eabi} means that the stack is aligned to a 16 byte boundary,
do not call an initialization function from @code{main}, and the
@option{-msdata} option will only use @code{r13} to point to a single
small data area.  The @option{-meabi} option is on by default if you
configured GCC using one of the @samp{powerpc*-*-eabi*} options.

@item -msdata=eabi
@opindex msdata=eabi
On System V.4 and embedded PowerPC systems, put small initialized
@code{const} global and static data in the @samp{.sdata2} section, which
is pointed to by register @code{r2}.  Put small initialized
non-@code{const} global and static data in the @samp{.sdata} section,
which is pointed to by register @code{r13}.  Put small uninitialized
global and static data in the @samp{.sbss} section, which is adjacent to
the @samp{.sdata} section.  The @option{-msdata=eabi} option is
incompatible with the @option{-mrelocatable} option.  The
@option{-msdata=eabi} option also sets the @option{-memb} option.

@item -msdata=sysv
@opindex msdata=sysv
On System V.4 and embedded PowerPC systems, put small global and static
data in the @samp{.sdata} section, which is pointed to by register
@code{r13}.  Put small uninitialized global and static data in the
@samp{.sbss} section, which is adjacent to the @samp{.sdata} section.
The @option{-msdata=sysv} option is incompatible with the
@option{-mrelocatable} option.

@item -msdata=default
@itemx -msdata
@opindex msdata=default
@opindex msdata
On System V.4 and embedded PowerPC systems, if @option{-meabi} is used,
compile code the same as @option{-msdata=eabi}, otherwise compile code the
same as @option{-msdata=sysv}.

@item -msdata-data
@opindex msdata-data
On System V.4 and embedded PowerPC systems, put small global and static
data in the @samp{.sdata} section.  Put small uninitialized global and
static data in the @samp{.sbss} section.  Do not use register @code{r13}
to address small data however.  This is the default behavior unless
other @option{-msdata} options are used.

@item -msdata=none
@itemx -mno-sdata
@opindex msdata=none
@opindex mno-sdata
On embedded PowerPC systems, put all initialized global and static data
in the @samp{.data} section, and all uninitialized data in the
@samp{.bss} section.

@item -G @var{num}
@opindex G
@cindex smaller data references (PowerPC)
@cindex .sdata/.sdata2 references (PowerPC)
On embedded PowerPC systems, put global and static items less than or
equal to @var{num} bytes into the small data or bss sections instead of
the normal data or bss section.  By default, @var{num} is 8.  The
@option{-G @var{num}} switch is also passed to the linker.
All modules should be compiled with the same @option{-G @var{num}} value.

@item -mregnames
@itemx -mno-regnames
@opindex mregnames
@opindex mno-regnames
On System V.4 and embedded PowerPC systems do (do not) emit register
names in the assembly language output using symbolic forms.

@item -mlongcall
@itemx -mno-longcall
@opindex mlongcall
@opindex mno-longcall
Default to making all function calls via pointers, so that functions
which reside further than 64 megabytes (67,108,864 bytes) from the
current location can be called.  This setting can be overridden by the
@code{shortcall} function attribute, or by @code{#pragma longcall(0)}.

Some linkers are capable of detecting out-of-range calls and generating
glue code on the fly.  On these systems, long calls are unnecessary and
generate slower code.  As of this writing, the AIX linker can do this,
as can the GNU linker for PowerPC/64.  It is planned to add this feature
to the GNU linker for 32-bit PowerPC systems as well.

In the future, we may cause GCC to ignore all longcall specifications
when the linker is known to generate glue.

@item -pthread
@opindex pthread
Adds support for multithreading with the @dfn{pthreads} library.
This option sets flags for both the preprocessor and linker.

@end table

@node Darwin Options
@subsection Darwin Options
@cindex Darwin options

These options are defined for all architectures running the Darwin operating
system.  They are useful for compatibility with other Mac OS compilers.

@table @gcctabopt
@item -all_load    
@opindex all_load   
Loads all members of static archive libraries.
See man ld(1) for more information.

@item -arch_errors_fatal
@opindex arch_errors_fatal
Cause the errors having to do with files that have the wrong architecture
to be fatal.

@item -bind_at_load
@opindex bind_at_load
Causes the output file to be marked such that the dynamic linker will
bind all undefined references when the file is loaded or launched.

@item -bundle     
@opindex bundle
Produce a Mach-o bundle format file.
See man ld(1) for more information.

@item -bundle_loader @var{executable}
@opindex bundle_loader
This specifies the @var{executable} that will be loading the build
output file being linked. See man ld(1) for more information.

@item -allowable_client  @var{client_name}
@item -arch_only

@item -client_name       
@item -compatibility_version
@item -current_version    
@item -dependency-file
@item -dylib_file    
@item -dylinker_install_name
@item -dynamic
@item -dynamiclib   
@item -exported_symbols_list  
@item -filelist
@item -flat_namespace   
@item -force_cpusubtype_ALL
@item -force_flat_namespace   
@item -headerpad_max_install_names
@item -image_base  
@item -init
@item -install_name
@item -keep_private_externs
@item -multi_module
@item -multiply_defined      
@item -multiply_defined_unused      
@item -noall_load  
@item -nomultidefs
@item -noprebind     
@item -noseglinkedit
@item -pagezero_size    
@item -prebind
@item -prebind_all_twolevel_modules
@item -private_bundle
@item -read_only_relocs
@item -sectalign  
@item -sectobjectsymbols    
@item -whyload
@item -seg1addr 
@item -sectcreate
@item -sectobjectsymbols
@item -sectorder
@item -seg_addr_table
@item -seg_addr_table_filename
@item -seglinkedit
@item -segprot   
@item -segs_read_only_addr
@item -segs_read_write_addr
@item -single_module   
@item -static
@item -sub_library
@item -sub_umbrella 
@item -twolevel_namespace
@item -umbrella
@item -undefined
@item -unexported_symbols_list
@item -weak_reference_mismatches
@item -whatsloaded  

@opindex allowable_client
@opindex arch_only    
@opindex client_name
@opindex compatibility_version
@opindex current_version
@opindex dependency-file
@opindex dylib_file
@opindex dylinker_install_name
@opindex dynamic
@opindex dynamiclib
@opindex exported_symbols_list
@opindex filelist  
@opindex flat_namespace    
@opindex force_cpusubtype_ALL
@opindex force_flat_namespace
@opindex headerpad_max_install_names
@opindex image_base
@opindex init     
@opindex install_name
@opindex keep_private_externs
@opindex multi_module   
@opindex multiply_defined
@opindex multiply_defined_unused   
@opindex noall_load  
@opindex nomultidefs   
@opindex noprebind
@opindex noseglinkedit      
@opindex pagezero_size
@opindex prebind
@opindex prebind_all_twolevel_modules
@opindex private_bundle 
@opindex read_only_relocs
@opindex sectalign   
@opindex sectobjectsymbols    
@opindex whyload  
@opindex seg1addr
@opindex sectcreate       
@opindex sectobjectsymbols 
@opindex sectorder     
@opindex seg_addr_table
@opindex seg_addr_table_filename
@opindex seglinkedit
@opindex segprot
@opindex segs_read_only_addr
@opindex segs_read_write_addr
@opindex single_module
@opindex static
@opindex sub_library
@opindex sub_umbrella
@opindex twolevel_namespace
@opindex umbrella
@opindex undefined
@opindex unexported_symbols_list
@opindex weak_reference_mismatches
@opindex whatsloaded

This options are available for Darwin linker. Darwin linker man page
describes them in detail.
@end table


@node RT Options
@subsection IBM RT Options
@cindex RT options
@cindex IBM RT options

These @samp{-m} options are defined for the IBM RT PC:

@table @gcctabopt
@item -min-line-mul
@opindex min-line-mul
Use an in-line code sequence for integer multiplies.  This is the
default.

@item -mcall-lib-mul
@opindex mcall-lib-mul
Call @code{lmul$$} for integer multiples.

@item -mfull-fp-blocks
@opindex mfull-fp-blocks
Generate full-size floating point data blocks, including the minimum
amount of scratch space recommended by IBM@.  This is the default.

@item -mminimum-fp-blocks
@opindex mminimum-fp-blocks
Do not include extra scratch space in floating point data blocks.  This
results in smaller code, but slower execution, since scratch space must
be allocated dynamically.

@cindex @file{stdarg.h} and RT PC
@item -mfp-arg-in-fpregs
@opindex mfp-arg-in-fpregs
Use a calling sequence incompatible with the IBM calling convention in
which floating point arguments are passed in floating point registers.
Note that @code{stdarg.h} will not work with floating point operands
if this option is specified.

@item -mfp-arg-in-gregs
@opindex mfp-arg-in-gregs
Use the normal calling convention for floating point arguments.  This is
the default.

@item -mhc-struct-return
@opindex mhc-struct-return
Return structures of more than one word in memory, rather than in a
register.  This provides compatibility with the MetaWare HighC (hc)
compiler.  Use the option @option{-fpcc-struct-return} for compatibility
with the Portable C Compiler (pcc).

@item -mnohc-struct-return
@opindex mnohc-struct-return
Return some structures of more than one word in registers, when
convenient.  This is the default.  For compatibility with the
IBM-supplied compilers, use the option @option{-fpcc-struct-return} or the
option @option{-mhc-struct-return}.
@end table

@node MIPS Options
@subsection MIPS Options
@cindex MIPS options

These @samp{-m} options are defined for the MIPS family of computers:

@table @gcctabopt

@item -march=@var{arch}
@opindex march
Generate code that will run on @var{arch}, which can be the name of a
generic MIPS ISA, or the name of a particular processor.
The ISA names are:
@samp{mips1}, @samp{mips2}, @samp{mips3}, @samp{mips4},
@samp{mips32}, @samp{mips32r2}, and @samp{mips64}.
The processor names are:
@samp{4kc}, @samp{4kp}, @samp{5kc}, @samp{20kc},
@samp{m4k},
@samp{r2000}, @samp{r3000}, @samp{r3900}, @samp{r4000}, @samp{r4400},
@samp{r4600}, @samp{r4650}, @samp{r6000}, @samp{r8000},
@samp{orion},
@samp{sb1},
@samp{vr4100}, @samp{vr4300}, and @samp{vr5000}.
The special value @samp{from-abi} selects the
most compatible architecture for the selected ABI (that is,
@samp{mips1} for 32-bit ABIs and @samp{mips3} for 64-bit ABIs)@.

In processor names, a final @samp{000} can be abbreviated as @samp{k}
(for example, @samp{-march=r2k}).  Prefixes are optional, and
@samp{vr} may be written @samp{r}.

GCC defines two macros based on the value of this option.  The first
is @samp{_MIPS_ARCH}, which gives the name of target architecture, as
a string.  The second has the form @samp{_MIPS_ARCH_@var{foo}},
where @var{foo} is the capitalized value of @samp{_MIPS_ARCH}@.
For example, @samp{-march=r2000} will set @samp{_MIPS_ARCH}
to @samp{"r2000"} and define the macro @samp{_MIPS_ARCH_R2000}.

Note that the @samp{_MIPS_ARCH} macro uses the processor names given
above.  In other words, it will have the full prefix and will not
abbreviate @samp{000} as @samp{k}.  In the case of @samp{from-abi},
the macro names the resolved architecture (either @samp{"mips1"} or
@samp{"mips3"}).  It names the default architecture when no
@option{-march} option is given.

@item -mtune=@var{arch}
@opindex mtune
Optimize for @var{arch}.  Among other things, this option controls
the way instructions are scheduled, and the perceived cost of arithmetic
operations.  The list of @var{arch} values is the same as for
@option{-march}.

When this option is not used, GCC will optimize for the processor
specified by @option{-march}.  By using @option{-march} and
@option{-mtune} together, it is possible to generate code that will
run on a family of processors, but optimize the code for one
particular member of that family.

@samp{-mtune} defines the macros @samp{_MIPS_TUNE} and
@samp{_MIPS_TUNE_@var{foo}}, which work in the same way as the
@samp{-march} ones described above.

@item -mips1
@opindex mips1
Equivalent to @samp{-march=mips1}.

@item -mips2
@opindex mips2
Equivalent to @samp{-march=mips2}.

@item -mips3
@opindex mips3
Equivalent to @samp{-march=mips3}.

@item -mips4
@opindex mips4
Equivalent to @samp{-march=mips4}.

@item -mips32
@opindex mips32
Equivalent to @samp{-march=mips32}.

@item -mips32r2
@opindex mips32r2
Equivalent to @samp{-march=mips32r2}.

@item -mips64
@opindex mips64
Equivalent to @samp{-march=mips64}.

@item -mfused-madd
@itemx -mno-fused-madd
@opindex mfused-madd
@opindex mno-fused-madd
Generate code that uses (does not use) the floating point multiply and
accumulate instructions, when they are available.  These instructions
are generated by default if they are available, but this may be
undesirable if the extra precision causes problems or on certain chips
in the mode where denormals are rounded to zero where denormals
generated by multiply and accumulate instructions cause exceptions
anyway.

@item -mfp32
@opindex mfp32
Assume that floating point registers are 32 bits wide.

@item -mfp64
@opindex mfp64
Assume that floating point registers are 64 bits wide.

@item -mgp32
@opindex mgp32
Assume that general purpose registers are 32 bits wide.

@item -mgp64
@opindex mgp64
Assume that general purpose registers are 64 bits wide.

@item -mint64
@opindex mint64
Force int and long types to be 64 bits wide.  See @option{-mlong32} for an
explanation of the default, and the width of pointers.

@item -mlong64
@opindex mlong64
Force long types to be 64 bits wide.  See @option{-mlong32} for an
explanation of the default, and the width of pointers.

@item -mlong32
@opindex mlong32
Force long, int, and pointer types to be 32 bits wide.

The default size of ints, longs and pointers depends on the ABI@.  All
the supported ABIs use 32-bit ints.  The n64 ABI uses 64-bit longs, as
does the 64-bit Cygnus EABI; the others use 32-bit longs.  Pointers
are the same size as longs, or the same size as integer registers,
whichever is smaller.

@item -mabi=32
@itemx -mabi=o64
@itemx -mabi=n32
@itemx -mabi=64
@itemx -mabi=eabi
@itemx -mabi=meabi
@opindex mabi=32
@opindex mabi=o64
@opindex mabi=n32
@opindex mabi=64
@opindex mabi=eabi
@opindex mabi=meabi
Generate code for the given ABI@.

Note that there are two embedded ABIs: @option{-mabi=eabi}
selects the one defined by Cygnus while @option{-meabi=meabi}
selects the one defined by MIPS@.  Both these ABIs have
32-bit and 64-bit variants.  Normally, GCC will generate
64-bit code when you select a 64-bit architecture, but you
can use @option{-mgp32} to get 32-bit code instead.

@item -mabi-fake-default
@opindex mabi-fake-default
You don't want to know what this option does.  No, really.  I mean
it.  Move on to the next option.

What?  You're still here?  Oh, well@enddots{}  Ok, here's the deal.  GCC
wants the default set of options to get the root of the multilib tree,
and the shared library SONAMEs without any multilib-indicating
suffixes.  This is not convenience for @samp{mips64-linux-gnu}, since
we want to default to the N32 ABI, while still being binary-compatible
with @samp{mips-linux-gnu} if you stick to the O32 ABI@.  Being
binary-compatible means shared libraries should have the same SONAMEs,
and libraries should live in the same location.  Having O32 libraries
in a sub-directory named say @file{o32} is not acceptable.

So we trick GCC into believing that O32 is the default ABI, except
that we override the default with some internal command-line
processing magic.  Problem is, if we stopped at that, and you then
created a multilib-aware package that used the output of @command{gcc
-print-multi-lib} to decide which multilibs to build, and how, and
you'd find yourself in an awkward situation when you found out that
some of the options listed ended up mapping to the same multilib, and
none of your libraries was actually built for the multilib that
@option{-print-multi-lib} claims to be the default.  So we added this
option that disables the default switcher, falling back to GCC's
original notion of the default library.  Confused yet?

For short: don't ever use this option, unless you find it in the list
of additional options to be used when building for multilibs, in the
output of @option{gcc -print-multi-lib}.

@item -mmips-as
@opindex mmips-as
Generate code for the MIPS assembler, and invoke @file{mips-tfile} to
add normal debug information.  This is the default for all
platforms except for the OSF/1 reference platform, using the OSF/rose
object format.  If the either of the @option{-gstabs} or @option{-gstabs+}
switches are used, the @file{mips-tfile} program will encapsulate the
stabs within MIPS ECOFF@.

@item -mgas
@opindex mgas
Generate code for the GNU assembler.  This is the default on the OSF/1
reference platform, using the OSF/rose object format.  Also, this is
the default if the configure option @option{--with-gnu-as} is used.

@item -msplit-addresses
@itemx -mno-split-addresses
@opindex msplit-addresses
@opindex mno-split-addresses
Generate code to load the high and low parts of address constants separately.
This allows GCC to optimize away redundant loads of the high order
bits of addresses.  This optimization requires GNU as and GNU ld.
This optimization is enabled by default for some embedded targets where
GNU as and GNU ld are standard.

@item -mrnames
@itemx -mno-rnames
@opindex mrnames
@opindex mno-rnames
The @option{-mrnames} switch says to output code using the MIPS software
names for the registers, instead of the hardware names (ie, @var{a0}
instead of @var{$4}).  The only known assembler that supports this option
is the Algorithmics assembler.

@item -mgpopt
@itemx -mno-gpopt
@opindex mgpopt
@opindex mno-gpopt
The @option{-mgpopt} switch says to write all of the data declarations
before the instructions in the text section, this allows the MIPS
assembler to generate one word memory references instead of using two
words for short global or static data items.  This is on by default if
optimization is selected.

@item -mmemcpy
@itemx -mno-memcpy
@opindex mmemcpy
@opindex mno-memcpy
The @option{-mmemcpy} switch makes all block moves call the appropriate
string function (@samp{memcpy} or @samp{bcopy}) instead of possibly
generating inline code.

@item -mmips-tfile
@itemx -mno-mips-tfile
@opindex mmips-tfile
@opindex mno-mips-tfile
The @option{-mno-mips-tfile} switch causes the compiler not
postprocess the object file with the @file{mips-tfile} program,
after the MIPS assembler has generated it to add debug support.  If
@file{mips-tfile} is not run, then no local variables will be
available to the debugger.  In addition, @file{stage2} and
@file{stage3} objects will have the temporary file names passed to the
assembler embedded in the object file, which means the objects will
not compare the same.  The @option{-mno-mips-tfile} switch should only
be used when there are bugs in the @file{mips-tfile} program that
prevents compilation.

@item -msoft-float
@opindex msoft-float
Generate output containing library calls for floating point.
@strong{Warning:} the requisite libraries are not part of GCC@.
Normally the facilities of the machine's usual C compiler are used, but
this can't be done directly in cross-compilation.  You must make your
own arrangements to provide suitable library functions for
cross-compilation.

@item -mhard-float
@opindex mhard-float
Generate output containing floating point instructions.  This is the
default if you use the unmodified sources.

@item -mabicalls
@itemx -mno-abicalls
@opindex mabicalls
@opindex mno-abicalls
Emit (or do not emit) the pseudo operations @samp{.abicalls},
@samp{.cpload}, and @samp{.cprestore} that some System V.4 ports use for
position independent code.

@item -mlong-calls
@itemx -mno-long-calls
@opindex mlong-calls
@opindex mno-long-calls
Do all calls with the @samp{JALR} instruction, which requires
loading up a function's address into a register before the call.
You need to use this switch, if you call outside of the current
512 megabyte segment to functions that are not through pointers.

@item -mhalf-pic
@itemx -mno-half-pic
@opindex mhalf-pic
@opindex mno-half-pic
Put pointers to extern references into the data section and load them
up, rather than put the references in the text section.

@item -membedded-pic
@itemx -mno-embedded-pic
@opindex membedded-pic
@opindex mno-embedded-pic
Generate PIC code suitable for some embedded systems.  All calls are
made using PC relative address, and all data is addressed using the $gp
register.  No more than 65536 bytes of global data may be used.  This
requires GNU as and GNU ld which do most of the work.  This currently
only works on targets which use ECOFF; it does not work with ELF@.

@item -membedded-data
@itemx -mno-embedded-data
@opindex membedded-data
@opindex mno-embedded-data
Allocate variables to the read-only data section first if possible, then
next in the small data section if possible, otherwise in data.  This gives
slightly slower code than the default, but reduces the amount of RAM required
when executing, and thus may be preferred for some embedded systems.

@item -muninit-const-in-rodata
@itemx -mno-uninit-const-in-rodata
@opindex muninit-const-in-rodata
@opindex mno-uninit-const-in-rodata
When used together with @option{-membedded-data}, it will always store uninitialized
const variables in the read-only data section.

@item -msingle-float
@itemx -mdouble-float
@opindex msingle-float
@opindex mdouble-float
The @option{-msingle-float} switch tells gcc to assume that the floating
point coprocessor only supports single precision operations, as on the
@samp{r4650} chip.  The @option{-mdouble-float} switch permits gcc to use
double precision operations.  This is the default.

@item -mmad
@itemx -mno-mad
@opindex mmad
@opindex mno-mad
Permit use of the @samp{mad}, @samp{madu} and @samp{mul} instructions,
as on the @samp{r4650} chip.

@item -m4650
@opindex m4650
Turns on @option{-msingle-float}, @option{-mmad}, and, at least for now,
@option{-mcpu=r4650}.

@item -mips16
@itemx -mno-mips16
@opindex mips16
@opindex mno-mips16
Enable 16-bit instructions.

@item -mentry
@opindex mentry
Use the entry and exit pseudo ops.  This option can only be used with
@option{-mips16}.

@item -EL
@opindex EL
Compile code for the processor in little endian mode.
The requisite libraries are assumed to exist.

@item -EB
@opindex EB
Compile code for the processor in big endian mode.
The requisite libraries are assumed to exist.

@item -G @var{num}
@opindex G
@cindex smaller data references (MIPS)
@cindex gp-relative references (MIPS)
Put global and static items less than or equal to @var{num} bytes into
the small data or bss sections instead of the normal data or bss
section.  This allows the assembler to emit one word memory reference
instructions based on the global pointer (@var{gp} or @var{$28}),
instead of the normal two words used.  By default, @var{num} is 8 when
the MIPS assembler is used, and 0 when the GNU assembler is used.  The
@option{-G @var{num}} switch is also passed to the assembler and linker.
All modules should be compiled with the same @option{-G @var{num}}
value.

@item -nocpp
@opindex nocpp
Tell the MIPS assembler to not run its preprocessor over user
assembler files (with a @samp{.s} suffix) when assembling them.

@item -mfix7000
@opindex mfix7000
Pass an option to gas which will cause nops to be inserted if
the read of the destination register of an mfhi or mflo instruction
occurs in the following two instructions.

@item -no-crt0
@opindex no-crt0
Do not include the default crt0.

@item -mflush-func=@var{func}
@itemx -mno-flush-func
@opindex mflush-func
Specifies the function to call to flush the I and D caches, or to not
call any such function.  If called, the function must take the same
arguments as the common @code{_flush_func()}, that is, the address of the
memory range for which the cache is being flushed, the size of the
memory range, and the number 3 (to flush both caches).  The default
depends on the target gcc was configured for, but commonly is either
@samp{_flush_func} or @samp{__cpu_flush}.

@item -mbranch-likely
@itemx -mno-branch-likely
@opindex mbranch-likely
@opindex mno-branch-likely
Enable or disable use of Branch Likely instructions, regardless of the
default for the selected architecture.  By default, Branch Likely
instructions may be generated if they are supported by the selected
architecture.  An exception is for the MIPS32 and MIPS64 architectures
and processors which implement those architectures; for those, Branch
Likely instructions will not be generated by default because the MIPS32
and MIPS64 architectures specifically deprecate their use.
@end table

@node i386 and x86-64 Options
@subsection Intel 386 and AMD x86-64 Options
@cindex i386 Options
@cindex x86-64 Options
@cindex Intel 386 Options
@cindex AMD x86-64 Options

These @samp{-m} options are defined for the i386 and x86-64 family of
computers:

@table @gcctabopt
@item -mtune=@var{cpu-type}
@opindex mtune
Tune to @var{cpu-type} everything applicable about the generated code, except
for the ABI and the set of available instructions.  The choices for
@var{cpu-type} are @samp{i386}, @samp{i486}, @samp{i586}, @samp{i686},
@samp{pentium}, @samp{pentium-mmx}, @samp{pentiumpro}, @samp{pentium2},
@samp{pentium3}, @samp{pentium4}, @samp{k6}, @samp{k6-2}, @samp{k6-3},
@samp{athlon}, @samp{athlon-tbird}, @samp{athlon-4}, @samp{athlon-xp},
@samp{athlon-mp}, @samp{winchip-c6}, @samp{winchip2}, @samp{k8}, @samp{c3}
and @samp{c3-2}.

While picking a specific @var{cpu-type} will schedule things appropriately
for that particular chip, the compiler will not generate any code that
does not run on the i386 without the @option{-march=@var{cpu-type}} option
being used.  @samp{i586} is equivalent to @samp{pentium} and @samp{i686}
is equivalent to @samp{pentiumpro}.  @samp{k6} and @samp{athlon} are the
AMD chips as opposed to the Intel ones.

@item -march=@var{cpu-type}
@opindex march
Generate instructions for the machine type @var{cpu-type}.  The choices
for @var{cpu-type} are the same as for @option{-mtune}.  Moreover,
specifying @option{-march=@var{cpu-type}} implies @option{-mtune=@var{cpu-type}}.

@item -mcpu=@var{cpu-type}
@opindex mcpu
A deprecated synonym for @option{-mtune}.

@item -m386
@itemx -m486
@itemx -mpentium
@itemx -mpentiumpro
@opindex m386
@opindex m486
@opindex mpentium
@opindex mpentiumpro
These options are synonyms for @option{-mtune=i386}, @option{-mtune=i486},
@option{-mtune=pentium}, and @option{-mtune=pentiumpro} respectively.
These synonyms are deprecated.

@item -mfpmath=@var{unit}
@opindex march
generate floating point arithmetics for selected unit @var{unit}.  the choices
for @var{unit} are:

@table @samp
@item 387
Use the standard 387 floating point coprocessor present majority of chips and
emulated otherwise.  Code compiled with this option will run almost everywhere.
The temporary results are computed in 80bit precision instead of precision
specified by the type resulting in slightly different results compared to most
of other chips. See @option{-ffloat-store} for more detailed description.

This is the default choice for i386 compiler.

@item sse
Use scalar floating point instructions present in the SSE instruction set.
This instruction set is supported by Pentium3 and newer chips, in the AMD line
by Athlon-4, Athlon-xp and Athlon-mp chips.  The earlier version of SSE
instruction set supports only single precision arithmetics, thus the double and
extended precision arithmetics is still done using 387.  Later version, present
only in Pentium4 and the future AMD x86-64 chips supports double precision
arithmetics too.

For i387 you need to use @option{-march=@var{cpu-type}}, @option{-msse} or
@option{-msse2} switches to enable SSE extensions and make this option
effective.  For x86-64 compiler, these extensions are enabled by default.

The resulting code should be considerably faster in majority of cases and avoid
the numerical instability problems of 387 code, but may break some existing
code that expects temporaries to be 80bit.

This is the default choice for x86-64 compiler.

@item sse,387
Attempt to utilize both instruction sets at once.  This effectively double the
amount of available registers and on chips with separate execution units for
387 and SSE the execution resources too.  Use this option with care, as it is
still experimental, because gcc register allocator does not model separate
functional units well resulting in instable performance.
@end table

@item -masm=@var{dialect}
@opindex masm=@var{dialect}
Output asm instructions using selected @var{dialect}. Supported choices are
@samp{intel} or @samp{att} (the default one).

@item -mieee-fp
@itemx -mno-ieee-fp
@opindex mieee-fp
@opindex mno-ieee-fp
Control whether or not the compiler uses IEEE floating point
comparisons.  These handle correctly the case where the result of a
comparison is unordered.

@item -msoft-float
@opindex msoft-float
Generate output containing library calls for floating point.
@strong{Warning:} the requisite libraries are not part of GCC@.
Normally the facilities of the machine's usual C compiler are used, but
this can't be done directly in cross-compilation.  You must make your
own arrangements to provide suitable library functions for
cross-compilation.

On machines where a function returns floating point results in the 80387
register stack, some floating point opcodes may be emitted even if
@option{-msoft-float} is used.

@item -mno-fp-ret-in-387
@opindex mno-fp-ret-in-387
Do not use the FPU registers for return values of functions.

The usual calling convention has functions return values of types
@code{float} and @code{double} in an FPU register, even if there
is no FPU@.  The idea is that the operating system should emulate
an FPU@.

The option @option{-mno-fp-ret-in-387} causes such values to be returned
in ordinary CPU registers instead.

@item -mno-fancy-math-387
@opindex mno-fancy-math-387
Some 387 emulators do not support the @code{sin}, @code{cos} and
@code{sqrt} instructions for the 387.  Specify this option to avoid
generating those instructions.  This option is the default on FreeBSD,
OpenBSD and NetBSD@.  This option is overridden when @option{-march}
indicates that the target cpu will always have an FPU and so the
instruction will not need emulation.  As of revision 2.6.1, these
instructions are not generated unless you also use the
@option{-funsafe-math-optimizations} switch.

@item -malign-double
@itemx -mno-align-double
@opindex malign-double
@opindex mno-align-double
Control whether GCC aligns @code{double}, @code{long double}, and
@code{long long} variables on a two word boundary or a one word
boundary.  Aligning @code{double} variables on a two word boundary will
produce code that runs somewhat faster on a @samp{Pentium} at the
expense of more memory.

@strong{Warning:} if you use the @option{-malign-double} switch,
structures containing the above types will be aligned differently than
the published application binary interface specifications for the 386
and will not be binary compatible with structures in code compiled
without that switch.

@item -m128bit-long-double
@opindex m128bit-long-double
Control the size of @code{long double} type. i386 application binary interface
specify the size to be 12 bytes, while modern architectures (Pentium and newer)
prefer @code{long double} aligned to 8 or 16 byte boundary.  This is
impossible to reach with 12 byte long doubles in the array accesses.

@strong{Warning:} if you use the @option{-m128bit-long-double} switch, the
structures and arrays containing @code{long double} will change their size as
well as function calling convention for function taking @code{long double}
will be modified.

@item -m96bit-long-double
@opindex m96bit-long-double
Set the size of @code{long double} to 96 bits as required by the i386
application binary interface.  This is the default.

@item -msvr3-shlib
@itemx -mno-svr3-shlib
@opindex msvr3-shlib
@opindex mno-svr3-shlib
Control whether GCC places uninitialized local variables into the
@code{bss} or @code{data} segments.  @option{-msvr3-shlib} places them
into @code{bss}.  These options are meaningful only on System V Release 3.

@item -mrtd
@opindex mrtd
Use a different function-calling convention, in which functions that
take a fixed number of arguments return with the @code{ret} @var{num}
instruction, which pops their arguments while returning.  This saves one
instruction in the caller since there is no need to pop the arguments
there.

You can specify that an individual function is called with this calling
sequence with the function attribute @samp{stdcall}.  You can also
override the @option{-mrtd} option by using the function attribute
@samp{cdecl}.  @xref{Function Attributes}.

@strong{Warning:} this calling convention is incompatible with the one
normally used on Unix, so you cannot use it if you need to call
libraries compiled with the Unix compiler.

Also, you must provide function prototypes for all functions that
take variable numbers of arguments (including @code{printf});
otherwise incorrect code will be generated for calls to those
functions.

In addition, seriously incorrect code will result if you call a
function with too many arguments.  (Normally, extra arguments are
harmlessly ignored.)

@item -mregparm=@var{num}
@opindex mregparm
Control how many registers are used to pass integer arguments.  By
default, no registers are used to pass arguments, and at most 3
registers can be used.  You can control this behavior for a specific
function by using the function attribute @samp{regparm}.
@xref{Function Attributes}.

@strong{Warning:} if you use this switch, and
@var{num} is nonzero, then you must build all modules with the same
value, including any libraries.  This includes the system libraries and
startup modules.

@item -mpreferred-stack-boundary=@var{num}
@opindex mpreferred-stack-boundary
Attempt to keep the stack boundary aligned to a 2 raised to @var{num}
byte boundary.  If @option{-mpreferred-stack-boundary} is not specified,
the default is 4 (16 bytes or 128 bits), except when optimizing for code
size (@option{-Os}), in which case the default is the minimum correct
alignment (4 bytes for x86, and 8 bytes for x86-64).

On Pentium and PentiumPro, @code{double} and @code{long double} values
should be aligned to an 8 byte boundary (see @option{-malign-double}) or
suffer significant run time performance penalties.  On Pentium III, the
Streaming SIMD Extension (SSE) data type @code{__m128} suffers similar
penalties if it is not 16 byte aligned.

To ensure proper alignment of this values on the stack, the stack boundary
must be as aligned as that required by any value stored on the stack.
Further, every function must be generated such that it keeps the stack
aligned.  Thus calling a function compiled with a higher preferred
stack boundary from a function compiled with a lower preferred stack
boundary will most likely misalign the stack.  It is recommended that
libraries that use callbacks always use the default setting.

This extra alignment does consume extra stack space, and generally
increases code size.  Code that is sensitive to stack space usage, such
as embedded systems and operating system kernels, may want to reduce the
preferred alignment to @option{-mpreferred-stack-boundary=2}.

@item -mmmx
@itemx -mno-mmx
@item -msse
@itemx -mno-sse
@item -msse2
@itemx -mno-sse2
@item -m3dnow
@itemx -mno-3dnow
@opindex mmmx
@opindex mno-mmx
@opindex msse
@opindex mno-sse
@opindex m3dnow
@opindex mno-3dnow
These switches enable or disable the use of built-in functions that allow
direct access to the MMX, SSE and 3Dnow extensions of the instruction set.

@xref{X86 Built-in Functions}, for details of the functions enabled
and disabled by these switches.

To have SSE/SSE2 instructions generated automatically from floating-point
code, see @option{-mfpmath=sse}.

@item -mpush-args
@itemx -mno-push-args
@opindex mpush-args
@opindex mno-push-args
Use PUSH operations to store outgoing parameters.  This method is shorter
and usually equally fast as method using SUB/MOV operations and is enabled
by default.  In some cases disabling it may improve performance because of
improved scheduling and reduced dependencies.

@item -maccumulate-outgoing-args
@opindex maccumulate-outgoing-args
If enabled, the maximum amount of space required for outgoing arguments will be
computed in the function prologue.  This is faster on most modern CPUs
because of reduced dependencies, improved scheduling and reduced stack usage
when preferred stack boundary is not equal to 2.  The drawback is a notable
increase in code size.  This switch implies @option{-mno-push-args}.

@item -mthreads
@opindex mthreads
Support thread-safe exception handling on @samp{Mingw32}.  Code that relies
on thread-safe exception handling must compile and link all code with the
@option{-mthreads} option.  When compiling, @option{-mthreads} defines
@option{-D_MT}; when linking, it links in a special thread helper library
@option{-lmingwthrd} which cleans up per thread exception handling data.

@item -mno-align-stringops
@opindex mno-align-stringops
Do not align destination of inlined string operations.  This switch reduces
code size and improves performance in case the destination is already aligned,
but gcc don't know about it.

@item -minline-all-stringops
@opindex minline-all-stringops
By default GCC inlines string operations only when destination is known to be
aligned at least to 4 byte boundary.  This enables more inlining, increase code
size, but may improve performance of code that depends on fast memcpy, strlen
and memset for short lengths.

@item -momit-leaf-frame-pointer
@opindex momit-leaf-frame-pointer
Don't keep the frame pointer in a register for leaf functions.  This
avoids the instructions to save, set up and restore frame pointers and
makes an extra register available in leaf functions.  The option
@option{-fomit-frame-pointer} removes the frame pointer for all functions
which might make debugging harder.
@end table

These @samp{-m} switches are supported in addition to the above
on AMD x86-64 processors in 64-bit environments.

@table @gcctabopt
@item -m32
@itemx -m64
@opindex m32
@opindex m64
Generate code for a 32-bit or 64-bit environment.
The 32-bit environment sets int, long and pointer to 32 bits and
generates code that runs on any i386 system.
The 64-bit environment sets int to 32 bits and long and pointer
to 64 bits and generates code for AMD's x86-64 architecture.

@item -mno-red-zone
@opindex no-red-zone
Do not use a so called red zone for x86-64 code.  The red zone is mandated
by the x86-64 ABI, it is a 128-byte area beyond the location of the
stack pointer that will not be modified by signal or interrupt handlers
and therefore can be used for temporary data without adjusting the stack
pointer.  The flag @option{-mno-red-zone} disables this red zone.

@item -mcmodel=small
@opindex mcmodel=small
Generate code for the small code model: the program and its symbols must
be linked in the lower 2 GB of the address space.  Pointers are 64 bits.
Programs can be statically or dynamically linked.  This is the default
code model.

@item -mcmodel=kernel
@opindex mcmodel=kernel
Generate code for the kernel code model.  The kernel runs in the
negative 2 GB of the address space.
This model has to be used for Linux kernel code.

@item -mcmodel=medium
@opindex mcmodel=medium
Generate code for the medium model: The program is linked in the lower 2
GB of the address space but symbols can be located anywhere in the
address space.  Programs can be statically or dynamically linked, but
building of shared libraries are not supported with the medium model.

@item -mcmodel=large
@opindex mcmodel=large
Generate code for the large model: This model makes no assumptions
about addresses and sizes of sections.  Currently GCC does not implement
this model.
@end table

@node HPPA Options
@subsection HPPA Options
@cindex HPPA Options

These @samp{-m} options are defined for the HPPA family of computers:

@table @gcctabopt
@item -march=@var{architecture-type}
@opindex march
Generate code for the specified architecture.  The choices for
@var{architecture-type} are @samp{1.0} for PA 1.0, @samp{1.1} for PA
1.1, and @samp{2.0} for PA 2.0 processors.  Refer to
@file{/usr/lib/sched.models} on an HP-UX system to determine the proper
architecture option for your machine.  Code compiled for lower numbered
architectures will run on higher numbered architectures, but not the
other way around.

PA 2.0 support currently requires gas snapshot 19990413 or later.  The
next release of binutils (current is 2.9.1) will probably contain PA 2.0
support.

@item -mpa-risc-1-0
@itemx -mpa-risc-1-1
@itemx -mpa-risc-2-0
@opindex mpa-risc-1-0
@opindex mpa-risc-1-1
@opindex mpa-risc-2-0
Synonyms for @option{-march=1.0}, @option{-march=1.1}, and @option{-march=2.0} respectively.

@item -mbig-switch
@opindex mbig-switch
Generate code suitable for big switch tables.  Use this option only if
the assembler/linker complain about out of range branches within a switch
table.

@item -mjump-in-delay
@opindex mjump-in-delay
Fill delay slots of function calls with unconditional jump instructions
by modifying the return pointer for the function call to be the target
of the conditional jump.

@item -mdisable-fpregs
@opindex mdisable-fpregs
Prevent floating point registers from being used in any manner.  This is
necessary for compiling kernels which perform lazy context switching of
floating point registers.  If you use this option and attempt to perform
floating point operations, the compiler will abort.

@item -mdisable-indexing
@opindex mdisable-indexing
Prevent the compiler from using indexing address modes.  This avoids some
rather obscure problems when compiling MIG generated code under MACH@.

@item -mno-space-regs
@opindex mno-space-regs
Generate code that assumes the target has no space registers.  This allows
GCC to generate faster indirect calls and use unscaled index address modes.

Such code is suitable for level 0 PA systems and kernels.

@item -mfast-indirect-calls
@opindex mfast-indirect-calls
Generate code that assumes calls never cross space boundaries.  This
allows GCC to emit code which performs faster indirect calls.

This option will not work in the presence of shared libraries or nested
functions.

@item -mlong-load-store
@opindex mlong-load-store
Generate 3-instruction load and store sequences as sometimes required by
the HP-UX 10 linker.  This is equivalent to the @samp{+k} option to
the HP compilers.

@item -mportable-runtime
@opindex mportable-runtime
Use the portable calling conventions proposed by HP for ELF systems.

@item -mgas
@opindex mgas
Enable the use of assembler directives only GAS understands.

@item -mschedule=@var{cpu-type}
@opindex mschedule
Schedule code according to the constraints for the machine type
@var{cpu-type}.  The choices for @var{cpu-type} are @samp{700}
@samp{7100}, @samp{7100LC}, @samp{7200}, @samp{7300} and @samp{8000}.  Refer
to @file{/usr/lib/sched.models} on an HP-UX system to determine the
proper scheduling option for your machine.  The default scheduling is
@samp{8000}.

@item -mlinker-opt
@opindex mlinker-opt
Enable the optimization pass in the HP-UX linker.  Note this makes symbolic
debugging impossible.  It also triggers a bug in the HP-UX 8 and HP-UX 9
linkers in which they give bogus error messages when linking some programs.

@item -msoft-float
@opindex msoft-float
Generate output containing library calls for floating point.
@strong{Warning:} the requisite libraries are not available for all HPPA
targets.  Normally the facilities of the machine's usual C compiler are
used, but this cannot be done directly in cross-compilation.  You must make
your own arrangements to provide suitable library functions for
cross-compilation.  The embedded target @samp{hppa1.1-*-pro}
does provide software floating point support.

@option{-msoft-float} changes the calling convention in the output file;
therefore, it is only useful if you compile @emph{all} of a program with
this option.  In particular, you need to compile @file{libgcc.a}, the
library that comes with GCC, with @option{-msoft-float} in order for
this to work.

@item -msio
@opindex msio
Generate the predefine, @code{_SIO}, for server IO.  The default is
@option{-mwsio}.  This generates the predefines, @code{__hp9000s700},
@code{__hp9000s700__} and @code{_WSIO}, for workstation IO.  These
options are available under HP-UX and HI-UX.

@item -mgnu-ld
@opindex gnu-ld
Use GNU ld specific options.  This passes @option{-shared} to ld when
building a shared library.  It is the default when GCC is configured,
explicitly or implicitly, with the GNU linker.  This option does not
have any affect on which ld is called, it only changes what parameters
are passed to that ld.  The ld that is called is determined by the
@option{--with-ld} configure option, gcc's program search path, and
finally by the user's @env{PATH}.  The linker used by GCC can be printed
using @samp{which `gcc -print-prog-name=ld`}.

@item -mhp-ld
@opindex hp-ld
Use HP ld specific options.  This passes @option{-b} to ld when building
a shared library and passes @option{+Accept TypeMismatch} to ld on all
links.  It is the default when GCC is configured, explicitly or
implicitly, with the HP linker.  This option does not have any affect on
which ld is called, it only changes what parameters are passed to that
ld.  The ld that is called is determined by the @option{--with-ld}
configure option, gcc's program search path, and finally by the user's
@env{PATH}.  The linker used by GCC can be printed using @samp{which
`gcc -print-prog-name=ld`}.

@item -mlong-calls
@opindex mno-long-calls
Generate code that uses long call sequences.  This ensures that a call
is always able to reach linker generated stubs.  The default is to generate
long calls only when the distance from the call site to the beginning
of the function or translation unit, as the case may be, exceeds a
predefined limit set by the branch type being used.  The limits for
normal calls are 7,600,000 and 240,000 bytes, respectively for the
PA 2.0 and PA 1.X architectures.  Sibcalls are always limited at
240,000 bytes.

Distances are measured from the beginning of functions when using the
@option{-ffunction-sections} option, or when using the @option{-mgas}
and @option{-mno-portable-runtime} options together under HP-UX with
the SOM linker.

It is normally not desirable to use this option as it will degrade
performance.  However, it may be useful in large applications,
particularly when partial linking is used to build the application.

The types of long calls used depends on the capabilities of the
assembler and linker, and the type of code being generated.  The
impact on systems that support long absolute calls, and long pic
symbol-difference or pc-relative calls should be relatively small.
However, an indirect call is used on 32-bit ELF systems in pic code
and it is quite long.

@item -nolibdld
@opindex nolibdld
Suppress the generation of link options to search libdld.sl when the
@option{-static} option is specified on HP-UX 10 and later.

@item -static
@opindex static
The HP-UX implementation of setlocale in libc has a dependency on
libdld.sl.  There isn't an archive version of libdld.sl.  Thus,
when the @option{-static} option is specified, special link options
are needed to resolve this dependency.

On HP-UX 10 and later, the GCC driver adds the necessary options to
link with libdld.sl when the @option{-static} option is specified.
This causes the resulting binary to be dynamic.  On the 64-bit port,
the linkers generate dynamic binaries by default in any case.  The
@option{-nolibdld} option can be used to prevent the GCC driver from
adding these link options.

@item -threads
@opindex threads
Add support for multithreading with the @dfn{dce thread} library
under HP-UX.  This option sets flags for both the preprocessor and
linker.
@end table

@node Intel 960 Options
@subsection Intel 960 Options

These @samp{-m} options are defined for the Intel 960 implementations:

@table @gcctabopt
@item -m@var{cpu-type}
@opindex mka
@opindex mkb
@opindex mmc
@opindex mca
@opindex mcf
@opindex msa
@opindex msb
Assume the defaults for the machine type @var{cpu-type} for some of
the other options, including instruction scheduling, floating point
support, and addressing modes.  The choices for @var{cpu-type} are
@samp{ka}, @samp{kb}, @samp{mc}, @samp{ca}, @samp{cf},
@samp{sa}, and @samp{sb}.
The default is
@samp{kb}.

@item -mnumerics
@itemx -msoft-float
@opindex mnumerics
@opindex msoft-float
The @option{-mnumerics} option indicates that the processor does support
floating-point instructions.  The @option{-msoft-float} option indicates
that floating-point support should not be assumed.

@item -mleaf-procedures
@itemx -mno-leaf-procedures
@opindex mleaf-procedures
@opindex mno-leaf-procedures
Do (or do not) attempt to alter leaf procedures to be callable with the
@code{bal} instruction as well as @code{call}.  This will result in more
efficient code for explicit calls when the @code{bal} instruction can be
substituted by the assembler or linker, but less efficient code in other
cases, such as calls via function pointers, or using a linker that doesn't
support this optimization.

@item -mtail-call
@itemx -mno-tail-call
@opindex mtail-call
@opindex mno-tail-call
Do (or do not) make additional attempts (beyond those of the
machine-independent portions of the compiler) to optimize tail-recursive
calls into branches.  You may not want to do this because the detection of
cases where this is not valid is not totally complete.  The default is
@option{-mno-tail-call}.

@item -mcomplex-addr
@itemx -mno-complex-addr
@opindex mcomplex-addr
@opindex mno-complex-addr
Assume (or do not assume) that the use of a complex addressing mode is a
win on this implementation of the i960.  Complex addressing modes may not
be worthwhile on the K-series, but they definitely are on the C-series.
The default is currently @option{-mcomplex-addr} for all processors except
the CB and CC@.

@item -mcode-align
@itemx -mno-code-align
@opindex mcode-align
@opindex mno-code-align
Align code to 8-byte boundaries for faster fetching (or don't bother).
Currently turned on by default for C-series implementations only.

@ignore
@item -mclean-linkage
@itemx -mno-clean-linkage
@opindex mclean-linkage
@opindex mno-clean-linkage
These options are not fully implemented.
@end ignore

@item -mic-compat
@itemx -mic2.0-compat
@itemx -mic3.0-compat
@opindex mic-compat
@opindex mic2.0-compat
@opindex mic3.0-compat
Enable compatibility with iC960 v2.0 or v3.0.

@item -masm-compat
@itemx -mintel-asm
@opindex masm-compat
@opindex mintel-asm
Enable compatibility with the iC960 assembler.

@item -mstrict-align
@itemx -mno-strict-align
@opindex mstrict-align
@opindex mno-strict-align
Do not permit (do permit) unaligned accesses.

@item -mold-align
@opindex mold-align
Enable structure-alignment compatibility with Intel's gcc release version
1.3 (based on gcc 1.37).  This option implies @option{-mstrict-align}.

@item -mlong-double-64
@opindex mlong-double-64
Implement type @samp{long double} as 64-bit floating point numbers.
Without the option @samp{long double} is implemented by 80-bit
floating point numbers.  The only reason we have it because there is
no 128-bit @samp{long double} support in @samp{fp-bit.c} yet.  So it
is only useful for people using soft-float targets.  Otherwise, we
should recommend against use of it.

@end table

@node DEC Alpha Options
@subsection DEC Alpha Options

These @samp{-m} options are defined for the DEC Alpha implementations:

@table @gcctabopt
@item -mno-soft-float
@itemx -msoft-float
@opindex mno-soft-float
@opindex msoft-float
Use (do not use) the hardware floating-point instructions for
floating-point operations.  When @option{-msoft-float} is specified,
functions in @file{libgcc.a} will be used to perform floating-point
operations.  Unless they are replaced by routines that emulate the
floating-point operations, or compiled in such a way as to call such
emulations routines, these routines will issue floating-point
operations.   If you are compiling for an Alpha without floating-point
operations, you must ensure that the library is built so as not to call
them.

Note that Alpha implementations without floating-point operations are
required to have floating-point registers.

@item -mfp-reg
@itemx -mno-fp-regs
@opindex mfp-reg
@opindex mno-fp-regs
Generate code that uses (does not use) the floating-point register set.
@option{-mno-fp-regs} implies @option{-msoft-float}.  If the floating-point
register set is not used, floating point operands are passed in integer
registers as if they were integers and floating-point results are passed
in @code{$0} instead of @code{$f0}.  This is a non-standard calling sequence,
so any function with a floating-point argument or return value called by code
compiled with @option{-mno-fp-regs} must also be compiled with that
option.

A typical use of this option is building a kernel that does not use,
and hence need not save and restore, any floating-point registers.

@item -mieee
@opindex mieee
The Alpha architecture implements floating-point hardware optimized for
maximum performance.  It is mostly compliant with the IEEE floating
point standard.  However, for full compliance, software assistance is
required.  This option generates code fully IEEE compliant code
@emph{except} that the @var{inexact-flag} is not maintained (see below).
If this option is turned on, the preprocessor macro @code{_IEEE_FP} is
defined during compilation.  The resulting code is less efficient but is
able to correctly support denormalized numbers and exceptional IEEE
values such as not-a-number and plus/minus infinity.  Other Alpha
compilers call this option @option{-ieee_with_no_inexact}.

@item -mieee-with-inexact
@opindex mieee-with-inexact
This is like @option{-mieee} except the generated code also maintains
the IEEE @var{inexact-flag}.  Turning on this option causes the
generated code to implement fully-compliant IEEE math.  In addition to
@code{_IEEE_FP}, @code{_IEEE_FP_EXACT} is defined as a preprocessor
macro.  On some Alpha implementations the resulting code may execute
significantly slower than the code generated by default.  Since there is
very little code that depends on the @var{inexact-flag}, you should
normally not specify this option.  Other Alpha compilers call this
option @option{-ieee_with_inexact}.

@item -mfp-trap-mode=@var{trap-mode}
@opindex mfp-trap-mode
This option controls what floating-point related traps are enabled.
Other Alpha compilers call this option @option{-fptm @var{trap-mode}}.
The trap mode can be set to one of four values:

@table @samp
@item n
This is the default (normal) setting.  The only traps that are enabled
are the ones that cannot be disabled in software (e.g., division by zero
trap).

@item u
In addition to the traps enabled by @samp{n}, underflow traps are enabled
as well.

@item su
Like @samp{su}, but the instructions are marked to be safe for software
completion (see Alpha architecture manual for details).

@item sui
Like @samp{su}, but inexact traps are enabled as well.
@end table

@item -mfp-rounding-mode=@var{rounding-mode}
@opindex mfp-rounding-mode
Selects the IEEE rounding mode.  Other Alpha compilers call this option
@option{-fprm @var{rounding-mode}}.  The @var{rounding-mode} can be one
of:

@table @samp
@item n
Normal IEEE rounding mode.  Floating point numbers are rounded towards
the nearest machine number or towards the even machine number in case
of a tie.

@item m
Round towards minus infinity.

@item c
Chopped rounding mode.  Floating point numbers are rounded towards zero.

@item d
Dynamic rounding mode.  A field in the floating point control register
(@var{fpcr}, see Alpha architecture reference manual) controls the
rounding mode in effect.  The C library initializes this register for
rounding towards plus infinity.  Thus, unless your program modifies the
@var{fpcr}, @samp{d} corresponds to round towards plus infinity.
@end table

@item -mtrap-precision=@var{trap-precision}
@opindex mtrap-precision
In the Alpha architecture, floating point traps are imprecise.  This
means without software assistance it is impossible to recover from a
floating trap and program execution normally needs to be terminated.
GCC can generate code that can assist operating system trap handlers
in determining the exact location that caused a floating point trap.
Depending on the requirements of an application, different levels of
precisions can be selected:

@table @samp
@item p
Program precision.  This option is the default and means a trap handler
can only identify which program caused a floating point exception.

@item f
Function precision.  The trap handler can determine the function that
caused a floating point exception.

@item i
Instruction precision.  The trap handler can determine the exact
instruction that caused a floating point exception.
@end table

Other Alpha compilers provide the equivalent options called
@option{-scope_safe} and @option{-resumption_safe}.

@item -mieee-conformant
@opindex mieee-conformant
This option marks the generated code as IEEE conformant.  You must not
use this option unless you also specify @option{-mtrap-precision=i} and either
@option{-mfp-trap-mode=su} or @option{-mfp-trap-mode=sui}.  Its only effect
is to emit the line @samp{.eflag 48} in the function prologue of the
generated assembly file.  Under DEC Unix, this has the effect that
IEEE-conformant math library routines will be linked in.

@item -mbuild-constants
@opindex mbuild-constants
Normally GCC examines a 32- or 64-bit integer constant to
see if it can construct it from smaller constants in two or three
instructions.  If it cannot, it will output the constant as a literal and
generate code to load it from the data segment at runtime.

Use this option to require GCC to construct @emph{all} integer constants
using code, even if it takes more instructions (the maximum is six).

You would typically use this option to build a shared library dynamic
loader.  Itself a shared library, it must relocate itself in memory
before it can find the variables and constants in its own data segment.

@item -malpha-as
@itemx -mgas
@opindex malpha-as
@opindex mgas
Select whether to generate code to be assembled by the vendor-supplied
assembler (@option{-malpha-as}) or by the GNU assembler @option{-mgas}.

@item -mbwx
@itemx -mno-bwx
@itemx -mcix
@itemx -mno-cix
@itemx -mfix
@itemx -mno-fix
@itemx -mmax
@itemx -mno-max
@opindex mbwx
@opindex mno-bwx
@opindex mcix
@opindex mno-cix
@opindex mfix
@opindex mno-fix
@opindex mmax
@opindex mno-max
Indicate whether GCC should generate code to use the optional BWX,
CIX, FIX and MAX instruction sets.  The default is to use the instruction
sets supported by the CPU type specified via @option{-mcpu=} option or that
of the CPU on which GCC was built if none was specified.

@item -mfloat-vax
@itemx -mfloat-ieee
@opindex mfloat-vax
@opindex mfloat-ieee
Generate code that uses (does not use) VAX F and G floating point
arithmetic instead of IEEE single and double precision.

@item -mexplicit-relocs
@itemx -mno-explicit-relocs
@opindex mexplicit-relocs
@opindex mno-explicit-relocs
Older Alpha assemblers provided no way to generate symbol relocations
except via assembler macros.  Use of these macros does not allow
optimal instruction scheduling.  GNU binutils as of version 2.12
supports a new syntax that allows the compiler to explicitly mark
which relocations should apply to which instructions.  This option
is mostly useful for debugging, as GCC detects the capabilities of
the assembler when it is built and sets the default accordingly.

@item -msmall-data
@itemx -mlarge-data
@opindex msmall-data
@opindex mlarge-data
When @option{-mexplicit-relocs} is in effect, static data is
accessed via @dfn{gp-relative} relocations.  When @option{-msmall-data}
is used, objects 8 bytes long or smaller are placed in a @dfn{small data area}
(the @code{.sdata} and @code{.sbss} sections) and are accessed via
16-bit relocations off of the @code{$gp} register.  This limits the
size of the small data area to 64KB, but allows the variables to be
directly accessed via a single instruction.

The default is @option{-mlarge-data}.  With this option the data area
is limited to just below 2GB.  Programs that require more than 2GB of
data must use @code{malloc} or @code{mmap} to allocate the data in the
heap instead of in the program's data segment.

When generating code for shared libraries, @option{-fpic} implies
@option{-msmall-data} and @option{-fPIC} implies @option{-mlarge-data}.

@item -msmall-text
@itemx -mlarge-text
@opindex msmall-text
@opindex mlarge-text
When @option{-msmall-text} is used, the compiler assumes that the
code of the entire program (or shared library) fits in 4MB, and is
thus reachable with a branch instruction.  When @option{-msmall-data}
is used, the compiler can assume that all local symbols share the
same @code{$gp} value, and thus reduce the number of instructions
required for a function call from 4 to 1.

The default is @option{-mlarge-text}.

@item -mcpu=@var{cpu_type}
@opindex mcpu
Set the instruction set and instruction scheduling parameters for
machine type @var{cpu_type}.  You can specify either the @samp{EV}
style name or the corresponding chip number.  GCC supports scheduling
parameters for the EV4, EV5 and EV6 family of processors and will
choose the default values for the instruction set from the processor
you specify.  If you do not specify a processor type, GCC will default
to the processor on which the compiler was built.

Supported values for @var{cpu_type} are

@table @samp
@item ev4
@item ev45
@itemx 21064
Schedules as an EV4 and has no instruction set extensions.

@item ev5
@itemx 21164
Schedules as an EV5 and has no instruction set extensions.

@item ev56
@itemx 21164a
Schedules as an EV5 and supports the BWX extension.

@item pca56
@itemx 21164pc
@itemx 21164PC
Schedules as an EV5 and supports the BWX and MAX extensions.

@item ev6
@itemx 21264
Schedules as an EV6 and supports the BWX, FIX, and MAX extensions.

@item ev67
@item 21264a
Schedules as an EV6 and supports the BWX, CIX, FIX, and MAX extensions.
@end table

@item -mtune=@var{cpu_type}
@opindex mtune
Set only the instruction scheduling parameters for machine type
@var{cpu_type}.  The instruction set is not changed.

@item -mmemory-latency=@var{time}
@opindex mmemory-latency
Sets the latency the scheduler should assume for typical memory
references as seen by the application.  This number is highly
dependent on the memory access patterns used by the application
and the size of the external cache on the machine.

Valid options for @var{time} are

@table @samp
@item @var{number}
A decimal number representing clock cycles.

@item L1
@itemx L2
@itemx L3
@itemx main
The compiler contains estimates of the number of clock cycles for
``typical'' EV4 & EV5 hardware for the Level 1, 2 & 3 caches
(also called Dcache, Scache, and Bcache), as well as to main memory.
Note that L3 is only valid for EV5.

@end table
@end table

@node DEC Alpha/VMS Options
@subsection DEC Alpha/VMS Options

These @samp{-m} options are defined for the DEC Alpha/VMS implementations:

@table @gcctabopt
@item -mvms-return-codes
@opindex mvms-return-codes
Return VMS condition codes from main.  The default is to return POSIX
style condition (e.g.@ error) codes.
@end table

@node H8/300 Options
@subsection H8/300 Options

These @samp{-m} options are defined for the H8/300 implementations:

@table @gcctabopt
@item -mrelax
@opindex mrelax
Shorten some address references at link time, when possible; uses the
linker option @option{-relax}.  @xref{H8/300,, @code{ld} and the H8/300,
ld.info, Using ld}, for a fuller description.

@item -mh
@opindex mh
Generate code for the H8/300H@.

@item -ms
@opindex ms
Generate code for the H8S@.

@item -mn
@opindex mn
Generate code for the H8S and H8/300H in the normal mode.  This switch
must be used either with -mh or -ms.

@item -ms2600
@opindex ms2600
Generate code for the H8S/2600.  This switch must be used with @option{-ms}.

@item -mint32
@opindex mint32
Make @code{int} data 32 bits by default.

@item -malign-300
@opindex malign-300
On the H8/300H and H8S, use the same alignment rules as for the H8/300.
The default for the H8/300H and H8S is to align longs and floats on 4
byte boundaries.
@option{-malign-300} causes them to be aligned on 2 byte boundaries.
This option has no effect on the H8/300.
@end table

@node SH Options
@subsection SH Options

These @samp{-m} options are defined for the SH implementations:

@table @gcctabopt
@item -m1
@opindex m1
Generate code for the SH1.

@item -m2
@opindex m2
Generate code for the SH2.

@item -m2e
Generate code for the SH2e.

@item -m3
@opindex m3
Generate code for the SH3.

@item -m3e
@opindex m3e
Generate code for the SH3e.

@item -m4-nofpu
@opindex m4-nofpu
Generate code for the SH4 without a floating-point unit.

@item -m4-single-only
@opindex m4-single-only
Generate code for the SH4 with a floating-point unit that only
supports single-precision arithmetic.

@item -m4-single
@opindex m4-single
Generate code for the SH4 assuming the floating-point unit is in
single-precision mode by default.

@item -m4
@opindex m4
Generate code for the SH4.

@item -mb
@opindex mb
Compile code for the processor in big endian mode.

@item -ml
@opindex ml
Compile code for the processor in little endian mode.

@item -mdalign
@opindex mdalign
Align doubles at 64-bit boundaries.  Note that this changes the calling
conventions, and thus some functions from the standard C library will
not work unless you recompile it first with @option{-mdalign}.

@item -mrelax
@opindex mrelax
Shorten some address references at link time, when possible; uses the
linker option @option{-relax}.

@item -mbigtable
@opindex mbigtable
Use 32-bit offsets in @code{switch} tables.  The default is to use
16-bit offsets.

@item -mfmovd
@opindex mfmovd
Enable the use of the instruction @code{fmovd}.

@item -mhitachi
@opindex mhitachi
Comply with the calling conventions defined by Hitachi.

@item -mnomacsave
@opindex mnomacsave
Mark the @code{MAC} register as call-clobbered, even if
@option{-mhitachi} is given.

@item -mieee
@opindex mieee
Increase IEEE-compliance of floating-point code.

@item -misize
@opindex misize
Dump instruction size and location in the assembly code.

@item -mpadstruct
@opindex mpadstruct
This option is deprecated.  It pads structures to multiple of 4 bytes,
which is incompatible with the SH ABI@.

@item -mspace
@opindex mspace
Optimize for space instead of speed.  Implied by @option{-Os}.

@item -mprefergot
@opindex mprefergot
When generating position-independent code, emit function calls using
the Global Offset Table instead of the Procedure Linkage Table.

@item -musermode
@opindex musermode
Generate a library function call to invalidate instruction cache
entries, after fixing up a trampoline.  This library function call
doesn't assume it can write to the whole memory address space.  This
is the default when the target is @code{sh-*-linux*}.
@end table

@node System V Options
@subsection Options for System V

These additional options are available on System V Release 4 for
compatibility with other compilers on those systems:

@table @gcctabopt
@item -G
@opindex G
Create a shared object.
It is recommended that @option{-symbolic} or @option{-shared} be used instead.

@item -Qy
@opindex Qy
Identify the versions of each tool used by the compiler, in a
@code{.ident} assembler directive in the output.

@item -Qn
@opindex Qn
Refrain from adding @code{.ident} directives to the output file (this is
the default).

@item -YP,@var{dirs}
@opindex YP
Search the directories @var{dirs}, and no others, for libraries
specified with @option{-l}.

@item -Ym,@var{dir}
@opindex Ym
Look in the directory @var{dir} to find the M4 preprocessor.
The assembler uses this option.
@c This is supposed to go with a -Yd for predefined M4 macro files, but
@c the generic assembler that comes with Solaris takes just -Ym.
@end table

@node TMS320C3x/C4x Options
@subsection TMS320C3x/C4x Options
@cindex TMS320C3x/C4x Options

These @samp{-m} options are defined for TMS320C3x/C4x implementations:

@table @gcctabopt

@item -mcpu=@var{cpu_type}
@opindex mcpu
Set the instruction set, register set, and instruction scheduling
parameters for machine type @var{cpu_type}.  Supported values for
@var{cpu_type} are @samp{c30}, @samp{c31}, @samp{c32}, @samp{c40}, and
@samp{c44}.  The default is @samp{c40} to generate code for the
TMS320C40.

@item -mbig-memory
@item -mbig
@itemx -msmall-memory
@itemx -msmall
@opindex mbig-memory
@opindex mbig
@opindex msmall-memory
@opindex msmall
Generates code for the big or small memory model.  The small memory
model assumed that all data fits into one 64K word page.  At run-time
the data page (DP) register must be set to point to the 64K page
containing the .bss and .data program sections.  The big memory model is
the default and requires reloading of the DP register for every direct
memory access.

@item -mbk
@itemx -mno-bk
@opindex mbk
@opindex mno-bk
Allow (disallow) allocation of general integer operands into the block
count register BK@.

@item -mdb
@itemx -mno-db
@opindex mdb
@opindex mno-db
Enable (disable) generation of code using decrement and branch,
DBcond(D), instructions.  This is enabled by default for the C4x.  To be
on the safe side, this is disabled for the C3x, since the maximum
iteration count on the C3x is @math{2^{23} + 1} (but who iterates loops more than
@math{2^{23}} times on the C3x?).  Note that GCC will try to reverse a loop so
that it can utilize the decrement and branch instruction, but will give
up if there is more than one memory reference in the loop.  Thus a loop
where the loop counter is decremented can generate slightly more
efficient code, in cases where the RPTB instruction cannot be utilized.

@item -mdp-isr-reload
@itemx -mparanoid
@opindex mdp-isr-reload
@opindex mparanoid
Force the DP register to be saved on entry to an interrupt service
routine (ISR), reloaded to point to the data section, and restored on
exit from the ISR@.  This should not be required unless someone has
violated the small memory model by modifying the DP register, say within
an object library.

@item -mmpyi
@itemx -mno-mpyi
@opindex mmpyi
@opindex mno-mpyi
For the C3x use the 24-bit MPYI instruction for integer multiplies
instead of a library call to guarantee 32-bit results.  Note that if one
of the operands is a constant, then the multiplication will be performed
using shifts and adds.  If the @option{-mmpyi} option is not specified for the C3x,
then squaring operations are performed inline instead of a library call.

@item -mfast-fix
@itemx -mno-fast-fix
@opindex mfast-fix
@opindex mno-fast-fix
The C3x/C4x FIX instruction to convert a floating point value to an
integer value chooses the nearest integer less than or equal to the
floating point value rather than to the nearest integer.  Thus if the
floating point number is negative, the result will be incorrectly
truncated an additional code is necessary to detect and correct this
case.  This option can be used to disable generation of the additional
code required to correct the result.

@item -mrptb
@itemx -mno-rptb
@opindex mrptb
@opindex mno-rptb
Enable (disable) generation of repeat block sequences using the RPTB
instruction for zero overhead looping.  The RPTB construct is only used
for innermost loops that do not call functions or jump across the loop
boundaries.  There is no advantage having nested RPTB loops due to the
overhead required to save and restore the RC, RS, and RE registers.
This is enabled by default with @option{-O2}.

@item -mrpts=@var{count}
@itemx -mno-rpts
@opindex mrpts
@opindex mno-rpts
Enable (disable) the use of the single instruction repeat instruction
RPTS@.  If a repeat block contains a single instruction, and the loop
count can be guaranteed to be less than the value @var{count}, GCC will
emit a RPTS instruction instead of a RPTB@.  If no value is specified,
then a RPTS will be emitted even if the loop count cannot be determined
at compile time.  Note that the repeated instruction following RPTS does
not have to be reloaded from memory each iteration, thus freeing up the
CPU buses for operands.  However, since interrupts are blocked by this
instruction, it is disabled by default.

@item -mloop-unsigned
@itemx -mno-loop-unsigned
@opindex mloop-unsigned
@opindex mno-loop-unsigned
The maximum iteration count when using RPTS and RPTB (and DB on the C40)
is @math{2^{31} + 1} since these instructions test if the iteration count is
negative to terminate the loop.  If the iteration count is unsigned
there is a possibility than the @math{2^{31} + 1} maximum iteration count may be
exceeded.  This switch allows an unsigned iteration count.

@item -mti
@opindex mti
Try to emit an assembler syntax that the TI assembler (asm30) is happy
with.  This also enforces compatibility with the API employed by the TI
C3x C compiler.  For example, long doubles are passed as structures
rather than in floating point registers.

@item -mregparm
@itemx -mmemparm
@opindex mregparm
@opindex mmemparm
Generate code that uses registers (stack) for passing arguments to functions.
By default, arguments are passed in registers where possible rather
than by pushing arguments on to the stack.

@item -mparallel-insns
@itemx -mno-parallel-insns
@opindex mparallel-insns
@opindex mno-parallel-insns
Allow the generation of parallel instructions.  This is enabled by
default with @option{-O2}.

@item -mparallel-mpy
@itemx -mno-parallel-mpy
@opindex mparallel-mpy
@opindex mno-parallel-mpy
Allow the generation of MPY||ADD and MPY||SUB parallel instructions,
provided @option{-mparallel-insns} is also specified.  These instructions have
tight register constraints which can pessimize the code generation
of large functions.

@end table

@node V850 Options
@subsection V850 Options
@cindex V850 Options

These @samp{-m} options are defined for V850 implementations:

@table @gcctabopt
@item -mlong-calls
@itemx -mno-long-calls
@opindex mlong-calls
@opindex mno-long-calls
Treat all calls as being far away (near).  If calls are assumed to be
far away, the compiler will always load the functions address up into a
register, and call indirect through the pointer.

@item -mno-ep
@itemx -mep
@opindex mno-ep
@opindex mep
Do not optimize (do optimize) basic blocks that use the same index
pointer 4 or more times to copy pointer into the @code{ep} register, and
use the shorter @code{sld} and @code{sst} instructions.  The @option{-mep}
option is on by default if you optimize.

@item -mno-prolog-function
@itemx -mprolog-function
@opindex mno-prolog-function
@opindex mprolog-function
Do not use (do use) external functions to save and restore registers at
the prolog and epilog of a function.  The external functions are slower,
but use less code space if more than one function saves the same number
of registers.  The @option{-mprolog-function} option is on by default if
you optimize.

@item -mspace
@opindex mspace
Try to make the code as small as possible.  At present, this just turns
on the @option{-mep} and @option{-mprolog-function} options.

@item -mtda=@var{n}
@opindex mtda
Put static or global variables whose size is @var{n} bytes or less into
the tiny data area that register @code{ep} points to.  The tiny data
area can hold up to 256 bytes in total (128 bytes for byte references).

@item -msda=@var{n}
@opindex msda
Put static or global variables whose size is @var{n} bytes or less into
the small data area that register @code{gp} points to.  The small data
area can hold up to 64 kilobytes.

@item -mzda=@var{n}
@opindex mzda
Put static or global variables whose size is @var{n} bytes or less into
the first 32 kilobytes of memory.

@item -mv850
@opindex mv850
Specify that the target processor is the V850.

@item -mbig-switch
@opindex mbig-switch
Generate code suitable for big switch tables.  Use this option only if
the assembler/linker complain about out of range branches within a switch
table.

@item -mapp-regs
@opindex -mapp-regs
This option will cause r2 and r5 to be used in the code generated by
the compiler.  This setting is the default.

@item -mno-app-regs
@opindex -mno-app-regs
This option will cause r2 and r5 to be treated as fixed registers.
  
@item -mv850e
@opindex -mv850e
Specify that the target processor is the V850E.  The preprocessor
constant @samp{__v850e__} will be defined if this option is used.

If neither @option{-mv850} nor @option{-mv850e} are defined
then a default target processor will be chosen and the relevant
@samp{__v850*__} preprocessor constant will be defined.

The preprocessor constants @samp{__v850} and @samp{__v851__} are always
defined, regardless of which processor variant is the target.

@item -mdisable-callt
@opindex -mdisable-callt
This option will suppress generation of the CALLT instruction for the
v850e flavors of the v850 architecture.  The default is
@option{-mno-disable-callt} which allows the CALLT instruction to be used.

@end table

@node ARC Options
@subsection ARC Options
@cindex ARC Options

These options are defined for ARC implementations:

@table @gcctabopt
@item -EL
@opindex EL
Compile code for little endian mode.  This is the default.

@item -EB
@opindex EB
Compile code for big endian mode.

@item -mmangle-cpu
@opindex mmangle-cpu
Prepend the name of the cpu to all public symbol names.
In multiple-processor systems, there are many ARC variants with different
instruction and register set characteristics.  This flag prevents code
compiled for one cpu to be linked with code compiled for another.
No facility exists for handling variants that are ``almost identical''.
This is an all or nothing option.

@item -mcpu=@var{cpu}
@opindex mcpu
Compile code for ARC variant @var{cpu}.
Which variants are supported depend on the configuration.
All variants support @option{-mcpu=base}, this is the default.

@item -mtext=@var{text-section}
@itemx -mdata=@var{data-section}
@itemx -mrodata=@var{readonly-data-section}
@opindex mtext
@opindex mdata
@opindex mrodata
Put functions, data, and readonly data in @var{text-section},
@var{data-section}, and @var{readonly-data-section} respectively
by default.  This can be overridden with the @code{section} attribute.
@xref{Variable Attributes}.

@end table

@node NS32K Options
@subsection NS32K Options
@cindex NS32K options

These are the @samp{-m} options defined for the 32000 series.  The default
values for these options depends on which style of 32000 was selected when
the compiler was configured; the defaults for the most common choices are
given below.

@table @gcctabopt
@item -m32032
@itemx -m32032
@opindex m32032
@opindex m32032
Generate output for a 32032.  This is the default
when the compiler is configured for 32032 and 32016 based systems.

@item -m32332
@itemx -m32332
@opindex m32332
@opindex m32332
Generate output for a 32332.  This is the default
when the compiler is configured for 32332-based systems.

@item -m32532
@itemx -m32532
@opindex m32532
@opindex m32532
Generate output for a 32532.  This is the default
when the compiler is configured for 32532-based systems.

@item -m32081
@opindex m32081
Generate output containing 32081 instructions for floating point.
This is the default for all systems.

@item -m32381
@opindex m32381
Generate output containing 32381 instructions for floating point.  This
also implies @option{-m32081}.  The 32381 is only compatible with the 32332
and 32532 cpus.  This is the default for the pc532-netbsd configuration.

@item -mmulti-add
@opindex mmulti-add
Try and generate multiply-add floating point instructions @code{polyF}
and @code{dotF}.  This option is only available if the @option{-m32381}
option is in effect.  Using these instructions requires changes to
register allocation which generally has a negative impact on
performance.  This option should only be enabled when compiling code
particularly likely to make heavy use of multiply-add instructions.

@item -mnomulti-add
@opindex mnomulti-add
Do not try and generate multiply-add floating point instructions
@code{polyF} and @code{dotF}.  This is the default on all platforms.

@item -msoft-float
@opindex msoft-float
Generate output containing library calls for floating point.
@strong{Warning:} the requisite libraries may not be available.

@item -mieee-compare
@itemx -mno-ieee-compare
@opindex mieee-compare
@opindex mno-ieee-compare
Control whether or not the compiler uses IEEE floating point
comparisons.  These handle correctly the case where the result of a
comparison is unordered.
@strong{Warning:} the requisite kernel support may not be available.

@item -mnobitfield
@opindex mnobitfield
Do not use the bit-field instructions.  On some machines it is faster to
use shifting and masking operations.  This is the default for the pc532.

@item -mbitfield
@opindex mbitfield
Do use the bit-field instructions.  This is the default for all platforms
except the pc532.

@item -mrtd
@opindex mrtd
Use a different function-calling convention, in which functions
that take a fixed number of arguments return pop their
arguments on return with the @code{ret} instruction.

This calling convention is incompatible with the one normally
used on Unix, so you cannot use it if you need to call libraries
compiled with the Unix compiler.

Also, you must provide function prototypes for all functions that
take variable numbers of arguments (including @code{printf});
otherwise incorrect code will be generated for calls to those
functions.

In addition, seriously incorrect code will result if you call a
function with too many arguments.  (Normally, extra arguments are
harmlessly ignored.)

This option takes its name from the 680x0 @code{rtd} instruction.


@item -mregparam
@opindex mregparam
Use a different function-calling convention where the first two arguments
are passed in registers.

This calling convention is incompatible with the one normally
used on Unix, so you cannot use it if you need to call libraries
compiled with the Unix compiler.

@item -mnoregparam
@opindex mnoregparam
Do not pass any arguments in registers.  This is the default for all
targets.

@item -msb
@opindex msb
It is OK to use the sb as an index register which is always loaded with
zero.  This is the default for the pc532-netbsd target.

@item -mnosb
@opindex mnosb
The sb register is not available for use or has not been initialized to
zero by the run time system.  This is the default for all targets except
the pc532-netbsd.  It is also implied whenever @option{-mhimem} or
@option{-fpic} is set.

@item -mhimem
@opindex mhimem
Many ns32000 series addressing modes use displacements of up to 512MB@.
If an address is above 512MB then displacements from zero can not be used.
This option causes code to be generated which can be loaded above 512MB@.
This may be useful for operating systems or ROM code.

@item -mnohimem
@opindex mnohimem
Assume code will be loaded in the first 512MB of virtual address space.
This is the default for all platforms.


@end table

@node AVR Options
@subsection AVR Options
@cindex AVR Options

These options are defined for AVR implementations:

@table @gcctabopt
@item -mmcu=@var{mcu}
@opindex mmcu
Specify ATMEL AVR instruction set or MCU type.

Instruction set avr1 is for the minimal AVR core, not supported by the C
compiler, only for assembler programs (MCU types: at90s1200, attiny10,
attiny11, attiny12, attiny15, attiny28).

Instruction set avr2 (default) is for the classic AVR core with up to
8K program memory space (MCU types: at90s2313, at90s2323, attiny22,
at90s2333, at90s2343, at90s4414, at90s4433, at90s4434, at90s8515,
at90c8534, at90s8535).

Instruction set avr3 is for the classic AVR core with up to 128K program
memory space (MCU types: atmega103, atmega603, at43usb320, at76c711).

Instruction set avr4 is for the enhanced AVR core with up to 8K program
memory space (MCU types: atmega8, atmega83, atmega85).

Instruction set avr5 is for the enhanced AVR core with up to 128K program
memory space (MCU types: atmega16, atmega161, atmega163, atmega32, atmega323,
atmega64, atmega128, at43usb355, at94k).

@item -msize
@opindex msize
Output instruction sizes to the asm file.

@item -minit-stack=@var{N}
@opindex minit-stack
Specify the initial stack address, which may be a symbol or numeric value,
@samp{__stack} is the default.

@item -mno-interrupts
@opindex mno-interrupts
Generated code is not compatible with hardware interrupts.
Code size will be smaller.

@item -mcall-prologues
@opindex mcall-prologues
Functions prologues/epilogues expanded as call to appropriate
subroutines.  Code size will be smaller.

@item -mno-tablejump
@opindex mno-tablejump
Do not generate tablejump insns which sometimes increase code size.

@item -mtiny-stack
@opindex mtiny-stack
Change only the low 8 bits of the stack pointer.
@end table

@node MCore Options
@subsection MCore Options
@cindex MCore options

These are the @samp{-m} options defined for the Motorola M*Core
processors.

@table @gcctabopt

@item -mhardlit
@itemx -mno-hardlit
@opindex mhardlit
@opindex mno-hardlit
Inline constants into the code stream if it can be done in two
instructions or less.

@item -mdiv
@itemx -mno-div
@opindex mdiv
@opindex mno-div
Use the divide instruction.  (Enabled by default).

@item -mrelax-immediate
@itemx -mno-relax-immediate
@opindex mrelax-immediate
@opindex mno-relax-immediate
Allow arbitrary sized immediates in bit operations.

@item -mwide-bitfields
@itemx -mno-wide-bitfields
@opindex mwide-bitfields
@opindex mno-wide-bitfields
Always treat bit-fields as int-sized.

@item -m4byte-functions
@itemx -mno-4byte-functions
@opindex m4byte-functions
@opindex mno-4byte-functions
Force all functions to be aligned to a four byte boundary.

@item -mcallgraph-data
@itemx -mno-callgraph-data
@opindex mcallgraph-data
@opindex mno-callgraph-data
Emit callgraph information.

@item -mslow-bytes
@itemx -mno-slow-bytes
@opindex mslow-bytes
@opindex mno-slow-bytes
Prefer word access when reading byte quantities.

@item -mlittle-endian
@itemx -mbig-endian
@opindex mlittle-endian
@opindex mbig-endian
Generate code for a little endian target.

@item -m210
@itemx -m340
@opindex m210
@opindex m340
Generate code for the 210 processor.
@end table

@node IA-64 Options
@subsection IA-64 Options
@cindex IA-64 Options

These are the @samp{-m} options defined for the Intel IA-64 architecture.

@table @gcctabopt
@item -mbig-endian
@opindex mbig-endian
Generate code for a big endian target.  This is the default for HP-UX@.

@item -mlittle-endian
@opindex mlittle-endian
Generate code for a little endian target.  This is the default for AIX5
and Linux.

@item -mgnu-as
@itemx -mno-gnu-as
@opindex mgnu-as
@opindex mno-gnu-as
Generate (or don't) code for the GNU assembler.  This is the default.
@c Also, this is the default if the configure option @option{--with-gnu-as}
@c is used.

@item -mgnu-ld
@itemx -mno-gnu-ld
@opindex mgnu-ld
@opindex mno-gnu-ld
Generate (or don't) code for the GNU linker.  This is the default.
@c Also, this is the default if the configure option @option{--with-gnu-ld}
@c is used.

@item -mno-pic
@opindex mno-pic
Generate code that does not use a global pointer register.  The result
is not position independent code, and violates the IA-64 ABI@.

@item -mvolatile-asm-stop
@itemx -mno-volatile-asm-stop
@opindex mvolatile-asm-stop
@opindex mno-volatile-asm-stop
Generate (or don't) a stop bit immediately before and after volatile asm
statements.

@item -mb-step
@opindex mb-step
Generate code that works around Itanium B step errata.

@item -mregister-names
@itemx -mno-register-names
@opindex mregister-names
@opindex mno-register-names
Generate (or don't) @samp{in}, @samp{loc}, and @samp{out} register names for
the stacked registers.  This may make assembler output more readable.

@item -mno-sdata
@itemx -msdata
@opindex mno-sdata
@opindex msdata
Disable (or enable) optimizations that use the small data section.  This may
be useful for working around optimizer bugs.

@item -mconstant-gp
@opindex mconstant-gp
Generate code that uses a single constant global pointer value.  This is
useful when compiling kernel code.

@item -mauto-pic
@opindex mauto-pic
Generate code that is self-relocatable.  This implies @option{-mconstant-gp}.
This is useful when compiling firmware code.

@item -minline-float-divide-min-latency
@opindex minline-float-divide-min-latency
Generate code for inline divides of floating point values
using the minimum latency algorithm.

@item -minline-float-divide-max-throughput
@opindex minline-float-divide-max-throughput
Generate code for inline divides of floating point values
using the maximum throughput algorithm.

@item -minline-int-divide-min-latency
@opindex minline-int-divide-min-latency
Generate code for inline divides of integer values
using the minimum latency algorithm.

@item -minline-int-divide-max-throughput
@opindex minline-int-divide-max-throughput
Generate code for inline divides of integer values
using the maximum throughput algorithm.

@item -mno-dwarf2-asm
@itemx -mdwarf2-asm
@opindex mno-dwarf2-asm
@opindex mdwarf2-asm
Don't (or do) generate assembler code for the DWARF2 line number debugging
info.  This may be useful when not using the GNU assembler.

@item -mfixed-range=@var{register-range}
@opindex mfixed-range
Generate code treating the given register range as fixed registers.
A fixed register is one that the register allocator can not use.  This is
useful when compiling kernel code.  A register range is specified as
two registers separated by a dash.  Multiple register ranges can be
specified separated by a comma.

@item -mearly-stop-bits
@itemx -mno-early-stop-bits
@opindex mearly-stop-bits
@opindex mno-early-stop-bits
Allow stop bits to be placed earlier than immediately preceding the
instruction that triggered the stop bit.  This can improve instruction
scheduling, but does not always do so.
@end table

@node D30V Options
@subsection D30V Options
@cindex D30V Options

These @samp{-m} options are defined for D30V implementations:

@table @gcctabopt
@item -mextmem
@opindex mextmem
Link the @samp{.text}, @samp{.data}, @samp{.bss}, @samp{.strings},
@samp{.rodata}, @samp{.rodata1}, @samp{.data1} sections into external
memory, which starts at location @code{0x80000000}.

@item -mextmemory
@opindex mextmemory
Same as the @option{-mextmem} switch.

@item -monchip
@opindex monchip
Link the @samp{.text} section into onchip text memory, which starts at
location @code{0x0}.  Also link @samp{.data}, @samp{.bss},
@samp{.strings}, @samp{.rodata}, @samp{.rodata1}, @samp{.data1} sections
into onchip data memory, which starts at location @code{0x20000000}.

@item -mno-asm-optimize
@itemx -masm-optimize
@opindex mno-asm-optimize
@opindex masm-optimize
Disable (enable) passing @option{-O} to the assembler when optimizing.
The assembler uses the @option{-O} option to automatically parallelize
adjacent short instructions where possible.

@item -mbranch-cost=@var{n}
@opindex mbranch-cost
Increase the internal costs of branches to @var{n}.  Higher costs means
that the compiler will issue more instructions to avoid doing a branch.
The default is 2.

@item -mcond-exec=@var{n}
@opindex mcond-exec
Specify the maximum number of conditionally executed instructions that
replace a branch.  The default is 4.
@end table

@node S/390 and zSeries Options
@subsection S/390 and zSeries Options
@cindex S/390 and zSeries Options

These are the @samp{-m} options defined for the S/390 and zSeries architecture.

@table @gcctabopt
@item -mhard-float
@itemx -msoft-float
@opindex mhard-float
@opindex msoft-float
Use (do not use) the hardware floating-point instructions and registers
for floating-point operations.  When @option{-msoft-float} is specified,
functions in @file{libgcc.a} will be used to perform floating-point
operations.  When @option{-mhard-float} is specified, the compiler
generates IEEE floating-point instructions.  This is the default.

@item -mbackchain
@itemx -mno-backchain
@opindex mbackchain
@opindex mno-backchain
Generate (or do not generate) code which maintains an explicit
backchain within the stack frame that points to the caller's frame.
This is currently needed to allow debugging.  The default is to
generate the backchain.

@item -msmall-exec
@itemx -mno-small-exec
@opindex msmall-exec
@opindex mno-small-exec
Generate (or do not generate) code using the @code{bras} instruction
to do subroutine calls.
This only works reliably if the total executable size does not
exceed 64k.  The default is to use the @code{basr} instruction instead,
which does not have this limitation.

@item -m64
@itemx -m31
@opindex m64
@opindex m31
When @option{-m31} is specified, generate code compliant to the
Linux for S/390 ABI@.  When @option{-m64} is specified, generate
code compliant to the Linux for zSeries ABI@.  This allows GCC in
particular to generate 64-bit instructions.  For the @samp{s390}
targets, the default is @option{-m31}, while the @samp{s390x}
targets default to @option{-m64}.

@item -mzarch
@itemx -mesa
@opindex mzarch
@opindex mesa
When @option{-mzarch} is specified, generate code using the 
instructions available on z/Architecture. 
When @option{-mesa} is specified, generate code using the 
instructions available on ESA/390. Note that @option{-mesa} is
not possible with @option{-m64}.
For the @samp{s390} targets, the default is @option{-mesa}, 
while the @samp{s390x} targets default to @option{-mzarch}.

@item -mmvcle
@itemx -mno-mvcle
@opindex mmvcle
@opindex mno-mvcle
Generate (or do not generate) code using the @code{mvcle} instruction
to perform block moves.  When @option{-mno-mvcle} is specified,
use a @code{mvc} loop instead.  This is the default.

@item -mdebug
@itemx -mno-debug
@opindex mdebug
@opindex mno-debug
Print (or do not print) additional debug information when compiling.
The default is to not print debug information.

@item -march=@var{arch}
@opindex march
Generate code that will run on @var{arch}, which is the name of system
representing a certain processor type. Possible values for
@var{cpu-type} are @samp{g5}, @samp{g6} and @samp{z900}. 

@item -mtune=@var{arch}
@opindex mtune
Tune to @var{cpu-type} everything applicable about the generated code,
 except for the ABI and the set of available instructions. 
The list of @var{arch} values is the same as for @option{-march}.

@end table

@node CRIS Options
@subsection CRIS Options
@cindex CRIS Options

These options are defined specifically for the CRIS ports.

@table @gcctabopt
@item -march=@var{architecture-type}
@itemx -mcpu=@var{architecture-type}
@opindex march
@opindex mcpu
Generate code for the specified architecture.  The choices for
@var{architecture-type} are @samp{v3}, @samp{v8} and @samp{v10} for
respectively ETRAX@w{ }4, ETRAX@w{ }100, and ETRAX@w{ }100@w{ }LX.
Default is @samp{v0} except for cris-axis-linux-gnu, where the default is
@samp{v10}.

@item -mtune=@var{architecture-type}
@opindex mtune
Tune to @var{architecture-type} everything applicable about the generated
code, except for the ABI and the set of available instructions.  The
choices for @var{architecture-type} are the same as for
@option{-march=@var{architecture-type}}.

@item -mmax-stack-frame=@var{n}
@opindex mmax-stack-frame
Warn when the stack frame of a function exceeds @var{n} bytes.

@item -melinux-stacksize=@var{n}
@opindex melinux-stacksize
Only available with the @samp{cris-axis-aout} target.  Arranges for
indications in the program to the kernel loader that the stack of the
program should be set to @var{n} bytes.

@item -metrax4
@itemx -metrax100
@opindex metrax4
@opindex metrax100
The options @option{-metrax4} and @option{-metrax100} are synonyms for
@option{-march=v3} and @option{-march=v8} respectively.

@item -mpdebug
@opindex mpdebug
Enable CRIS-specific verbose debug-related information in the assembly
code.  This option also has the effect to turn off the @samp{#NO_APP}
formatted-code indicator to the assembler at the beginning of the
assembly file.

@item -mcc-init
@opindex mcc-init
Do not use condition-code results from previous instruction; always emit
compare and test instructions before use of condition codes.

@item -mno-side-effects
@opindex mno-side-effects
Do not emit instructions with side-effects in addressing modes other than
post-increment.

@item -mstack-align
@itemx -mno-stack-align
@itemx -mdata-align
@itemx -mno-data-align
@itemx -mconst-align
@itemx -mno-const-align
@opindex mstack-align
@opindex mno-stack-align
@opindex mdata-align
@opindex mno-data-align
@opindex mconst-align
@opindex mno-const-align
These options (no-options) arranges (eliminate arrangements) for the
stack-frame, individual data and constants to be aligned for the maximum
single data access size for the chosen CPU model.  The default is to
arrange for 32-bit alignment.  ABI details such as structure layout are
not affected by these options.

@item -m32-bit
@itemx -m16-bit
@itemx -m8-bit
@opindex m32-bit
@opindex m16-bit
@opindex m8-bit
Similar to the stack- data- and const-align options above, these options
arrange for stack-frame, writable data and constants to all be 32-bit,
16-bit or 8-bit aligned.  The default is 32-bit alignment.

@item -mno-prologue-epilogue
@itemx -mprologue-epilogue
@opindex mno-prologue-epilogue
@opindex mprologue-epilogue
With @option{-mno-prologue-epilogue}, the normal function prologue and
epilogue that sets up the stack-frame are omitted and no return
instructions or return sequences are generated in the code.  Use this
option only together with visual inspection of the compiled code: no
warnings or errors are generated when call-saved registers must be saved,
or storage for local variable needs to be allocated.

@item -mno-gotplt
@itemx -mgotplt
@opindex mno-gotplt
@opindex mgotplt
With @option{-fpic} and @option{-fPIC}, don't generate (do generate)
instruction sequences that load addresses for functions from the PLT part
of the GOT rather than (traditional on other architectures) calls to the
PLT.  The default is @option{-mgotplt}.

@item -maout
@opindex maout
Legacy no-op option only recognized with the cris-axis-aout target.

@item -melf
@opindex melf
Legacy no-op option only recognized with the cris-axis-elf and
cris-axis-linux-gnu targets.

@item -melinux
@opindex melinux
Only recognized with the cris-axis-aout target, where it selects a
GNU/linux-like multilib, include files and instruction set for
@option{-march=v8}.

@item -mlinux
@opindex mlinux
Legacy no-op option only recognized with the cris-axis-linux-gnu target.

@item -sim
@opindex sim
This option, recognized for the cris-axis-aout and cris-axis-elf arranges
to link with input-output functions from a simulator library.  Code,
initialized data and zero-initialized data are allocated consecutively.

@item -sim2
@opindex sim2
Like @option{-sim}, but pass linker options to locate initialized data at
0x40000000 and zero-initialized data at 0x80000000.
@end table

@node MMIX Options
@subsection MMIX Options
@cindex MMIX Options

These options are defined for the MMIX:

@table @gcctabopt
@item -mlibfuncs
@itemx -mno-libfuncs
@opindex mlibfuncs
@opindex mno-libfuncs
Specify that intrinsic library functions are being compiled, passing all
values in registers, no matter the size.

@item -mepsilon
@itemx -mno-epsilon
@opindex mepsilon
@opindex mno-epsilon
Generate floating-point comparison instructions that compare with respect
to the @code{rE} epsilon register.

@item -mabi=mmixware
@itemx -mabi=gnu
@opindex mabi-mmixware
@opindex mabi=gnu
Generate code that passes function parameters and return values that (in
the called function) are seen as registers @code{$0} and up, as opposed to
the GNU ABI which uses global registers @code{$231} and up.

@item -mzero-extend
@itemx -mno-zero-extend
@opindex mzero-extend
@opindex mno-zero-extend
When reading data from memory in sizes shorter than 64 bits, use (do not
use) zero-extending load instructions by default, rather than
sign-extending ones.

@item -mknuthdiv
@itemx -mno-knuthdiv
@opindex mknuthdiv
@opindex mno-knuthdiv
Make the result of a division yielding a remainder have the same sign as
the divisor.  With the default, @option{-mno-knuthdiv}, the sign of the
remainder follows the sign of the dividend.  Both methods are
arithmetically valid, the latter being almost exclusively used.

@item -mtoplevel-symbols
@itemx -mno-toplevel-symbols
@opindex mtoplevel-symbols
@opindex mno-toplevel-symbols
Prepend (do not prepend) a @samp{:} to all global symbols, so the assembly
code can be used with the @code{PREFIX} assembly directive.

@item -melf
@opindex melf
Generate an executable in the ELF format, rather than the default
@samp{mmo} format used by the @command{mmix} simulator.

@item -mbranch-predict
@itemx -mno-branch-predict
@opindex mbranch-predict
@opindex mno-branch-predict
Use (do not use) the probable-branch instructions, when static branch
prediction indicates a probable branch.

@item -mbase-addresses
@itemx -mno-base-addresses
@opindex mbase-addresses
@opindex mno-base-addresses
Generate (do not generate) code that uses @emph{base addresses}.  Using a
base address automatically generates a request (handled by the assembler
and the linker) for a constant to be set up in a global register.  The
register is used for one or more base address requests within the range 0
to 255 from the value held in the register.  The generally leads to short
and fast code, but the number of different data items that can be
addressed is limited.  This means that a program that uses lots of static
data may require @option{-mno-base-addresses}.

@item -msingle-exit
@itemx -mno-single-exit
@opindex msingle-exit
@opindex mno-single-exit
Force (do not force) generated code to have a single exit point in each
function.
@end table

@node PDP-11 Options
@subsection PDP-11 Options
@cindex PDP-11 Options

These options are defined for the PDP-11:

@table @gcctabopt
@item -mfpu
@opindex mfpu
Use hardware FPP floating point.  This is the default.  (FIS floating
point on the PDP-11/40 is not supported.)

@item -msoft-float
@opindex msoft-float
Do not use hardware floating point.

@item -mac0
@opindex mac0
Return floating-point results in ac0 (fr0 in Unix assembler syntax).

@item -mno-ac0
@opindex mno-ac0
Return floating-point results in memory.  This is the default.

@item -m40
@opindex m40
Generate code for a PDP-11/40.

@item -m45
@opindex m45
Generate code for a PDP-11/45.  This is the default.

@item -m10
@opindex m10
Generate code for a PDP-11/10.

@item -mbcopy-builtin
@opindex bcopy-builtin
Use inline @code{movstrhi} patterns for copying memory.  This is the
default.

@item -mbcopy
@opindex mbcopy
Do not use inline @code{movstrhi} patterns for copying memory.

@item -mint16
@itemx -mno-int32
@opindex mint16
@opindex mno-int32
Use 16-bit @code{int}.  This is the default.

@item -mint32
@itemx -mno-int16
@opindex mint32
@opindex mno-int16
Use 32-bit @code{int}.

@item -mfloat64
@itemx -mno-float32
@opindex mfloat64
@opindex mno-float32
Use 64-bit @code{float}.  This is the default.

@item -mfloat32
@item -mno-float64
@opindex mfloat32
@opindex mno-float64
Use 32-bit @code{float}.

@item -mabshi
@opindex mabshi
Use @code{abshi2} pattern.  This is the default.

@item -mno-abshi
@opindex mno-abshi
Do not use @code{abshi2} pattern.

@item -mbranch-expensive
@opindex mbranch-expensive
Pretend that branches are expensive.  This is for experimenting with
code generation only.

@item -mbranch-cheap
@opindex mbranch-cheap
Do not pretend that branches are expensive.  This is the default.

@item -msplit
@opindex msplit
Generate code for a system with split I&D.

@item -mno-split
@opindex mno-split
Generate code for a system without split I&D.  This is the default.

@item -munix-asm
@opindex munix-asm
Use Unix assembler syntax.  This is the default when configured for
@samp{pdp11-*-bsd}.

@item -mdec-asm
@opindex mdec-asm
Use DEC assembler syntax.  This is the default when configured for any
PDP-11 target other than @samp{pdp11-*-bsd}.
@end table

@node Xstormy16 Options
@subsection Xstormy16 Options
@cindex Xstormy16 Options

These options are defined for Xstormy16:

@table @gcctabopt
@item -msim
@opindex msim
Choose startup files and linker script suitable for the simulator.
@end table

@node FRV Options
@subsection FRV Options
@cindex FRV Options

@table @gcctabopt
@item -mgpr-32
@opindex mgpr-32

Only use the first 32 general purpose registers.

@item -mgpr-64
@opindex mgpr-64

Use all 64 general purpose registers.

@item -mfpr-32
@opindex mfpr-32

Use only the first 32 floating point registers.

@item -mfpr-64
@opindex mfpr-64

Use all 64 floating point registers

@item -mhard-float
@opindex mhard-float

Use hardware instructions for floating point operations.

@item -msoft-float
@opindex msoft-float

Use library routines for floating point operations.

@item -malloc-cc
@opindex malloc-cc

Dynamically allocate condition code registers.

@item -mfixed-cc
@opindex mfixed-cc

Do not try to dynamically allocate condition code registers, only
use @code{icc0} and @code{fcc0}.

@item -mdword
@opindex mdword

Change ABI to use double word insns.

@item -mno-dword
@opindex mno-dword

Do not use double word instructions.

@item -mdouble
@opindex mdouble

Use floating point double instructions.

@item -mno-double
@opindex mno-double

Do not use floating point double instructions.

@item -mmedia
@opindex mmedia

Use media instructions.

@item -mno-media
@opindex mno-media

Do not use media instructions.

@item -mmuladd
@opindex mmuladd

Use multiply and add/subtract instructions.

@item -mno-muladd
@opindex mno-muladd

Do not use multiply and add/subtract instructions.

@item -mlibrary-pic
@opindex mlibrary-pic

Enable PIC support for building libraries

@item -macc-4
@opindex macc-4

Use only the first four media accumulator registers.

@item -macc-8
@opindex macc-8

Use all eight media accumulator registers.

@item -mpack
@opindex mpack

Pack VLIW instructions.

@item -mno-pack
@opindex mno-pack

Do not pack VLIW instructions.

@item -mno-eflags
@opindex mno-eflags

Do not mark ABI switches in e_flags.

@item -mcond-move
@opindex mcond-move

Enable the use of conditional-move instructions (default).

This switch is mainly for debugging the compiler and will likely be removed
in a future version.

@item -mno-cond-move
@opindex mno-cond-move

Disable the use of conditional-move instructions.

This switch is mainly for debugging the compiler and will likely be removed
in a future version.

@item -mscc
@opindex mscc

Enable the use of conditional set instructions (default).

This switch is mainly for debugging the compiler and will likely be removed
in a future version.

@item -mno-scc
@opindex mno-scc

Disable the use of conditional set instructions.

This switch is mainly for debugging the compiler and will likely be removed
in a future version.

@item -mcond-exec
@opindex mcond-exec

Enable the use of conditional execution (default).

This switch is mainly for debugging the compiler and will likely be removed
in a future version.

@item -mno-cond-exec
@opindex mno-cond-exec

Disable the use of conditional execution.

This switch is mainly for debugging the compiler and will likely be removed
in a future version.

@item -mvliw-branch
@opindex mvliw-branch

Run a pass to pack branches into VLIW instructions (default).

This switch is mainly for debugging the compiler and will likely be removed
in a future version.

@item -mno-vliw-branch
@opindex mno-vliw-branch

Do not run a pass to pack branches into VLIW instructions.

This switch is mainly for debugging the compiler and will likely be removed
in a future version.

@item -mmulti-cond-exec
@opindex mmulti-cond-exec

Enable optimization of @code{&&} and @code{||} in conditional execution
(default).

This switch is mainly for debugging the compiler and will likely be removed
in a future version.

@item -mno-multi-cond-exec
@opindex mno-multi-cond-exec

Disable optimization of @code{&&} and @code{||} in conditional execution.

This switch is mainly for debugging the compiler and will likely be removed
in a future version.

@item -mnested-cond-exec
@opindex mnested-cond-exec

Enable nested conditional execution optimizations (default).

This switch is mainly for debugging the compiler and will likely be removed
in a future version.

@item -mno-nested-cond-exec
@opindex mno-nested-cond-exec

Disable nested conditional execution optimizations.

This switch is mainly for debugging the compiler and will likely be removed
in a future version.

@item -mtomcat-stats
@opindex mtomcat-stats

Cause gas to print out tomcat statistics.

@item -mcpu=@var{cpu}
@opindex mcpu

Select the processor type for which to generate code.  Possible values are
@samp{simple}, @samp{tomcat}, @samp{fr500}, @samp{fr400}, @samp{fr300},
@samp{frv}.

@end table

@node Xtensa Options
@subsection Xtensa Options
@cindex Xtensa Options

The Xtensa architecture is designed to support many different
configurations.  The compiler's default options can be set to match a
particular Xtensa configuration by copying a configuration file into the
GCC sources when building GCC@.  The options below may be used to
override the default options.

@table @gcctabopt
@item -mbig-endian
@itemx -mlittle-endian
@opindex mbig-endian
@opindex mlittle-endian
Specify big-endian or little-endian byte ordering for the target Xtensa
processor.

@item -mdensity
@itemx -mno-density
@opindex mdensity
@opindex mno-density
Enable or disable use of the optional Xtensa code density instructions.

@item -mconst16
@itemx -mno-const16
@opindex mconst16
@opindex mno-const16
Enable or disable use of @code{CONST16} instructions for loading
constant values.  The @code{CONST16} instruction is currently not a
standard option from Tensilica.  When enabled, @code{CONST16}
instructions are always used in place of the standard @code{L32R}
instructions.  The use of @code{CONST16} is enabled by default only if
the @code{L32R} instruction is not available.

@item -mabs
@itemx -mno-abs
@opindex mabs
@opindex mno-abs
Enable or disable use of the Xtensa @code{ABS} instruction for absolute
value operations.

@item -maddx
@itemx -mno-addx
@opindex maddx
@opindex mno-addx
Enable or disable use of the Xtensa @code{ADDX} and @code{SUBX}
instructions.

@item -mmac16
@itemx -mno-mac16
@opindex mmac16
@opindex mno-mac16
Enable or disable use of the Xtensa MAC16 option.  When enabled, GCC
will generate MAC16 instructions from standard C code, with the
limitation that it will use neither the MR register file nor any
instruction that operates on the MR registers.  When this option is
disabled, GCC will translate 16-bit multiply/accumulate operations to a
combination of core instructions and library calls, depending on whether
any other multiplier options are enabled.

@item -mmul16
@itemx -mno-mul16
@opindex mmul16
@opindex mno-mul16
Enable or disable use of the 16-bit integer multiplier option.  When
enabled, the compiler will generate 16-bit multiply instructions for
multiplications of 16 bits or smaller in standard C code.  When this
option is disabled, the compiler will either use 32-bit multiply or
MAC16 instructions if they are available or generate library calls to
perform the multiply operations using shifts and adds.

@item -mmul32
@itemx -mno-mul32
@opindex mmul32
@opindex mno-mul32
Enable or disable use of the 32-bit integer multiplier option.  When
enabled, the compiler will generate 32-bit multiply instructions for
multiplications of 32 bits or smaller in standard C code.  When this
option is disabled, the compiler will generate library calls to perform
the multiply operations using either shifts and adds or 16-bit multiply
instructions if they are available.

@item -mnsa
@itemx -mno-nsa
@opindex mnsa
@opindex mno-nsa
Enable or disable use of the optional normalization shift amount
(@code{NSA}) instructions to implement the built-in @code{ffs} function.

@item -mminmax
@itemx -mno-minmax
@opindex mminmax
@opindex mno-minmax
Enable or disable use of the optional minimum and maximum value
instructions.

@item -msext
@itemx -mno-sext
@opindex msext
@opindex mno-sext
Enable or disable use of the optional sign extend (@code{SEXT})
instruction.

@item -mbooleans
@itemx -mno-booleans
@opindex mbooleans
@opindex mno-booleans
Enable or disable support for the boolean register file used by Xtensa
coprocessors.  This is not typically useful by itself but may be
required for other options that make use of the boolean registers (e.g.,
the floating-point option).

@item -mhard-float
@itemx -msoft-float
@opindex mhard-float
@opindex msoft-float
Enable or disable use of the floating-point option.  When enabled, GCC
generates floating-point instructions for 32-bit @code{float}
operations.  When this option is disabled, GCC generates library calls
to emulate 32-bit floating-point operations using integer instructions.
Regardless of this option, 64-bit @code{double} operations are always
emulated with calls to library functions.

@item -mfused-madd
@itemx -mno-fused-madd
@opindex mfused-madd
@opindex mno-fused-madd
Enable or disable use of fused multiply/add and multiply/subtract
instructions in the floating-point option.  This has no effect if the
floating-point option is not also enabled.  Disabling fused multiply/add
and multiply/subtract instructions forces the compiler to use separate
instructions for the multiply and add/subtract operations.  This may be
desirable in some cases where strict IEEE 754-compliant results are
required: the fused multiply add/subtract instructions do not round the
intermediate result, thereby producing results with @emph{more} bits of
precision than specified by the IEEE standard.  Disabling fused multiply
add/subtract instructions also ensures that the program output is not
sensitive to the compiler's ability to combine multiply and add/subtract
operations.

@item -mtext-section-literals
@itemx -mno-text-section-literals
@opindex mtext-section-literals
@opindex mno-text-section-literals
Control the treatment of literal pools.  The default is
@option{-mno-text-section-literals}, which places literals in a separate
section in the output file.  This allows the literal pool to be placed
in a data RAM/ROM, and it also allows the linker to combine literal
pools from separate object files to remove redundant literals and
improve code size.  With @option{-mtext-section-literals}, the literals
are interspersed in the text section in order to keep them as close as
possible to their references.  This may be necessary for large assembly
files.

@item -mtarget-align
@itemx -mno-target-align
@opindex mtarget-align
@opindex mno-target-align
When this option is enabled, GCC instructs the assembler to
automatically align instructions to reduce branch penalties at the
expense of some code density.  The assembler attempts to widen density
instructions to align branch targets and the instructions following call
instructions.  If there are not enough preceding safe density
instructions to align a target, no widening will be performed.  The
default is @option{-mtarget-align}.  These options do not affect the
treatment of auto-aligned instructions like @code{LOOP}, which the
assembler will always align, either by widening density instructions or
by inserting no-op instructions.

@item -mlongcalls
@itemx -mno-longcalls
@opindex mlongcalls
@opindex mno-longcalls
When this option is enabled, GCC instructs the assembler to translate
direct calls to indirect calls unless it can determine that the target
of a direct call is in the range allowed by the call instruction.  This
translation typically occurs for calls to functions in other source
files.  Specifically, the assembler translates a direct @code{CALL}
instruction into an @code{L32R} followed by a @code{CALLX} instruction.
The default is @option{-mno-longcalls}.  This option should be used in
programs where the call target can potentially be out of range.  This
option is implemented in the assembler, not the compiler, so the
assembly code generated by GCC will still show direct call
instructions---look at the disassembled object code to see the actual
instructions.  Note that the assembler will use an indirect call for
every cross-file call, not just those that really will be out of range.
@end table

@node Code Gen Options
@section Options for Code Generation Conventions
@cindex code generation conventions
@cindex options, code generation
@cindex run-time options

These machine-independent options control the interface conventions
used in code generation.

Most of them have both positive and negative forms; the negative form
of @option{-ffoo} would be @option{-fno-foo}.  In the table below, only
one of the forms is listed---the one which is not the default.  You
can figure out the other form by either removing @samp{no-} or adding
it.

@table @gcctabopt
@item -fbounds-check
@opindex fbounds-check
For front-ends that support it, generate additional code to check that
indices used to access arrays are within the declared range.  This is
currently only supported by the Java and Fortran 77 front-ends, where
this option defaults to true and false respectively.

@item -ftrapv
@opindex ftrapv
This option generates traps for signed overflow on addition, subtraction,
multiplication operations.

@item -fexceptions
@opindex fexceptions
Enable exception handling.  Generates extra code needed to propagate
exceptions.  For some targets, this implies GCC will generate frame
unwind information for all functions, which can produce significant data
size overhead, although it does not affect execution.  If you do not
specify this option, GCC will enable it by default for languages like
C++ which normally require exception handling, and disable it for
languages like C that do not normally require it.  However, you may need
to enable this option when compiling C code that needs to interoperate
properly with exception handlers written in C++.  You may also wish to
disable this option if you are compiling older C++ programs that don't
use exception handling.

@item -fnon-call-exceptions
@opindex fnon-call-exceptions
Generate code that allows trapping instructions to throw exceptions.
Note that this requires platform-specific runtime support that does
not exist everywhere.  Moreover, it only allows @emph{trapping}
instructions to throw exceptions, i.e.@: memory references or floating
point instructions.  It does not allow exceptions to be thrown from
arbitrary signal handlers such as @code{SIGALRM}.

@item -funwind-tables
@opindex funwind-tables
Similar to @option{-fexceptions}, except that it will just generate any needed
static data, but will not affect the generated code in any other way.
You will normally not enable this option; instead, a language processor
that needs this handling would enable it on your behalf.

@item -fasynchronous-unwind-tables
@opindex funwind-tables
Generate unwind table in dwarf2 format, if supported by target machine.  The
table is exact at each instruction boundary, so it can be used for stack
unwinding from asynchronous events (such as debugger or garbage collector).

@item -fpcc-struct-return
@opindex fpcc-struct-return
Return ``short'' @code{struct} and @code{union} values in memory like
longer ones, rather than in registers.  This convention is less
efficient, but it has the advantage of allowing intercallability between
GCC-compiled files and files compiled with other compilers, particularly
the Portable C Compiler (pcc).

The precise convention for returning structures in memory depends
on the target configuration macros.

Short structures and unions are those whose size and alignment match
that of some integer type.

@strong{Warning:} code compiled with the @option{-fpcc-struct-return}
switch is not binary compatible with code compiled with the
@option{-freg-struct-return} switch.
Use it to conform to a non-default application binary interface.

@item -freg-struct-return
@opindex freg-struct-return
Return @code{struct} and @code{union} values in registers when possible.
This is more efficient for small structures than
@option{-fpcc-struct-return}.

If you specify neither @option{-fpcc-struct-return} nor
@option{-freg-struct-return}, GCC defaults to whichever convention is
standard for the target.  If there is no standard convention, GCC
defaults to @option{-fpcc-struct-return}, except on targets where GCC is
the principal compiler.  In those cases, we can choose the standard, and
we chose the more efficient register return alternative.

@strong{Warning:} code compiled with the @option{-freg-struct-return}
switch is not binary compatible with code compiled with the
@option{-fpcc-struct-return} switch.
Use it to conform to a non-default application binary interface.

@item -fshort-enums
@opindex fshort-enums
Allocate to an @code{enum} type only as many bytes as it needs for the
declared range of possible values.  Specifically, the @code{enum} type
will be equivalent to the smallest integer type which has enough room.

@strong{Warning:} the @option{-fshort-enums} switch causes GCC to generate
code that is not binary compatible with code generated without that switch.
Use it to conform to a non-default application binary interface.

@item -fshort-double
@opindex fshort-double
Use the same size for @code{double} as for @code{float}.

@strong{Warning:} the @option{-fshort-double} switch causes GCC to generate
code that is not binary compatible with code generated without that switch.
Use it to conform to a non-default application binary interface.

@item -fshort-wchar
@opindex fshort-wchar
Override the underlying type for @samp{wchar_t} to be @samp{short
unsigned int} instead of the default for the target.  This option is
useful for building programs to run under WINE@.

@strong{Warning:} the @option{-fshort-wchar} switch causes GCC to generate
code that is not binary compatible with code generated without that switch.
Use it to conform to a non-default application binary interface.

@item -fshared-data
@opindex fshared-data
Requests that the data and non-@code{const} variables of this
compilation be shared data rather than private data.  The distinction
makes sense only on certain operating systems, where shared data is
shared between processes running the same program, while private data
exists in one copy per process.

@item -fno-common
@opindex fno-common
In C, allocate even uninitialized global variables in the data section of the
object file, rather than generating them as common blocks.  This has the
effect that if the same variable is declared (without @code{extern}) in
two different compilations, you will get an error when you link them.
The only reason this might be useful is if you wish to verify that the
program will work on other systems which always work this way.

@item -fno-ident
@opindex fno-ident
Ignore the @samp{#ident} directive.

@item -fno-gnu-linker
@opindex fno-gnu-linker
Do not output global initializations (such as C++ constructors and
destructors) in the form used by the GNU linker (on systems where the GNU
linker is the standard method of handling them).  Use this option when
you want to use a non-GNU linker, which also requires using the
@command{collect2} program to make sure the system linker includes
constructors and destructors.  (@command{collect2} is included in the GCC
distribution.)  For systems which @emph{must} use @command{collect2}, the
compiler driver @command{gcc} is configured to do this automatically.

@item -finhibit-size-directive
@opindex finhibit-size-directive
Don't output a @code{.size} assembler directive, or anything else that
would cause trouble if the function is split in the middle, and the
two halves are placed at locations far apart in memory.  This option is
used when compiling @file{crtstuff.c}; you should not need to use it
for anything else.

@item -fverbose-asm
@opindex fverbose-asm
Put extra commentary information in the generated assembly code to
make it more readable.  This option is generally only of use to those
who actually need to read the generated assembly code (perhaps while
debugging the compiler itself).

@option{-fno-verbose-asm}, the default, causes the
extra information to be omitted and is useful when comparing two assembler
files.

@item -fpic
@opindex fpic
@cindex global offset table
@cindex PIC
Generate position-independent code (PIC) suitable for use in a shared
library, if supported for the target machine.  Such code accesses all
constant addresses through a global offset table (GOT)@.  The dynamic
loader resolves the GOT entries when the program starts (the dynamic
loader is not part of GCC; it is part of the operating system).  If
the GOT size for the linked executable exceeds a machine-specific
maximum size, you get an error message from the linker indicating that
@option{-fpic} does not work; in that case, recompile with @option{-fPIC}
instead.  (These maximums are 16k on the m88k, 8k on the SPARC, and 32k
on the m68k and RS/6000.  The 386 has no such limit.)

Position-independent code requires special support, and therefore works
only on certain machines.  For the 386, GCC supports PIC for System V
but not for the Sun 386i.  Code generated for the IBM RS/6000 is always
position-independent.

@item -fPIC
@opindex fPIC
If supported for the target machine, emit position-independent code,
suitable for dynamic linking and avoiding any limit on the size of the
global offset table.  This option makes a difference on the m68k, m88k,
and the SPARC.

Position-independent code requires special support, and therefore works
only on certain machines.

@item -ffixed-@var{reg}
@opindex ffixed
Treat the register named @var{reg} as a fixed register; generated code
should never refer to it (except perhaps as a stack pointer, frame
pointer or in some other fixed role).

@var{reg} must be the name of a register.  The register names accepted
are machine-specific and are defined in the @code{REGISTER_NAMES}
macro in the machine description macro file.

This flag does not have a negative form, because it specifies a
three-way choice.

@item -fcall-used-@var{reg}
@opindex fcall-used
Treat the register named @var{reg} as an allocable register that is
clobbered by function calls.  It may be allocated for temporaries or
variables that do not live across a call.  Functions compiled this way
will not save and restore the register @var{reg}.

It is an error to used this flag with the frame pointer or stack pointer.
Use of this flag for other registers that have fixed pervasive roles in
the machine's execution model will produce disastrous results.

This flag does not have a negative form, because it specifies a
three-way choice.

@item -fcall-saved-@var{reg}
@opindex fcall-saved
Treat the register named @var{reg} as an allocable register saved by
functions.  It may be allocated even for temporaries or variables that
live across a call.  Functions compiled this way will save and restore
the register @var{reg} if they use it.

It is an error to used this flag with the frame pointer or stack pointer.
Use of this flag for other registers that have fixed pervasive roles in
the machine's execution model will produce disastrous results.

A different sort of disaster will result from the use of this flag for
a register in which function values may be returned.

This flag does not have a negative form, because it specifies a
three-way choice.

@item -fpack-struct
@opindex fpack-struct
Pack all structure members together without holes.

@strong{Warning:} the @option{-fpack-struct} switch causes GCC to generate
code that is not binary compatible with code generated without that switch.
Additionally, it makes the code suboptimal.
Use it to conform to a non-default application binary interface.

@item -finstrument-functions
@opindex finstrument-functions
Generate instrumentation calls for entry and exit to functions.  Just
after function entry and just before function exit, the following
profiling functions will be called with the address of the current
function and its call site.  (On some platforms,
@code{__builtin_return_address} does not work beyond the current
function, so the call site information may not be available to the
profiling functions otherwise.)

@example
void __cyg_profile_func_enter (void *this_fn,
                               void *call_site);
void __cyg_profile_func_exit  (void *this_fn,
                               void *call_site);
@end example

The first argument is the address of the start of the current function,
which may be looked up exactly in the symbol table.

This instrumentation is also done for functions expanded inline in other
functions.  The profiling calls will indicate where, conceptually, the
inline function is entered and exited.  This means that addressable
versions of such functions must be available.  If all your uses of a
function are expanded inline, this may mean an additional expansion of
code size.  If you use @samp{extern inline} in your C code, an
addressable version of such functions must be provided.  (This is
normally the case anyways, but if you get lucky and the optimizer always
expands the functions inline, you might have gotten away without
providing static copies.)

A function may be given the attribute @code{no_instrument_function}, in
which case this instrumentation will not be done.  This can be used, for
example, for the profiling functions listed above, high-priority
interrupt routines, and any functions from which the profiling functions
cannot safely be called (perhaps signal handlers, if the profiling
routines generate output or allocate memory).

@item -fstack-check
@opindex fstack-check
Generate code to verify that you do not go beyond the boundary of the
stack.  You should specify this flag if you are running in an
environment with multiple threads, but only rarely need to specify it in
a single-threaded environment since stack overflow is automatically
detected on nearly all systems if there is only one stack.

Note that this switch does not actually cause checking to be done; the
operating system must do that.  The switch causes generation of code
to ensure that the operating system sees the stack being extended.

@item -fstack-limit-register=@var{reg}
@itemx -fstack-limit-symbol=@var{sym}
@itemx -fno-stack-limit
@opindex fstack-limit-register
@opindex fstack-limit-symbol
@opindex fno-stack-limit
Generate code to ensure that the stack does not grow beyond a certain value,
either the value of a register or the address of a symbol.  If the stack
would grow beyond the value, a signal is raised.  For most targets,
the signal is raised before the stack overruns the boundary, so
it is possible to catch the signal without taking special precautions.

For instance, if the stack starts at absolute address @samp{0x80000000}
and grows downwards, you can use the flags
@option{-fstack-limit-symbol=__stack_limit} and
@option{-Wl,--defsym,__stack_limit=0x7ffe0000} to enforce a stack limit
of 128KB@.  Note that this may only work with the GNU linker.

@cindex aliasing of parameters
@cindex parameters, aliased
@item -fargument-alias
@itemx -fargument-noalias
@itemx -fargument-noalias-global
@opindex fargument-alias
@opindex fargument-noalias
@opindex fargument-noalias-global
Specify the possible relationships among parameters and between
parameters and global data.

@option{-fargument-alias} specifies that arguments (parameters) may
alias each other and may alias global storage.@*
@option{-fargument-noalias} specifies that arguments do not alias
each other, but may alias global storage.@*
@option{-fargument-noalias-global} specifies that arguments do not
alias each other and do not alias global storage.

Each language will automatically use whatever option is required by
the language standard.  You should not need to use these options yourself.

@item -fleading-underscore
@opindex fleading-underscore
This option and its counterpart, @option{-fno-leading-underscore}, forcibly
change the way C symbols are represented in the object file.  One use
is to help link with legacy assembly code.

@strong{Warning:} the @option{-fleading-underscore} switch causes GCC to
generate code that is not binary compatible with code generated without that
switch.  Use it to conform to a non-default application binary interface.
Not all targets provide complete support for this switch.

@item -ftls-model=@var{model}
Alter the thread-local storage model to be used (@pxref{Thread-Local}).
The @var{model} argument should be one of @code{global-dynamic},
@code{local-dynamic}, @code{initial-exec} or @code{local-exec}.

The default without @option{-fpic} is @code{initial-exec}; with
@option{-fpic} the default is @code{global-dynamic}.
@end table

@c man end

@node Environment Variables
@section Environment Variables Affecting GCC
@cindex environment variables

@c man begin ENVIRONMENT
This section describes several environment variables that affect how GCC
operates.  Some of them work by specifying directories or prefixes to use
when searching for various kinds of files.  Some are used to specify other
aspects of the compilation environment.

Note that you can also specify places to search using options such as
@option{-B}, @option{-I} and @option{-L} (@pxref{Directory Options}).  These
take precedence over places specified using environment variables, which
in turn take precedence over those specified by the configuration of GCC@.
@xref{Driver,, Controlling the Compilation Driver @file{gcc}, gccint,
GNU Compiler Collection (GCC) Internals}.

@table @env
@item LANG
@itemx LC_CTYPE
@c @itemx LC_COLLATE
@itemx LC_MESSAGES
@c @itemx LC_MONETARY
@c @itemx LC_NUMERIC
@c @itemx LC_TIME
@itemx LC_ALL
@findex LANG
@findex LC_CTYPE
@c @findex LC_COLLATE
@findex LC_MESSAGES
@c @findex LC_MONETARY
@c @findex LC_NUMERIC
@c @findex LC_TIME
@findex LC_ALL
@cindex locale
These environment variables control the way that GCC uses
localization information that allow GCC to work with different
national conventions.  GCC inspects the locale categories
@env{LC_CTYPE} and @env{LC_MESSAGES} if it has been configured to do
so.  These locale categories can be set to any value supported by your
installation.  A typical value is @samp{en_UK} for English in the United
Kingdom.

The @env{LC_CTYPE} environment variable specifies character
classification.  GCC uses it to determine the character boundaries in
a string; this is needed for some multibyte encodings that contain quote
and escape characters that would otherwise be interpreted as a string
end or escape.

The @env{LC_MESSAGES} environment variable specifies the language to
use in diagnostic messages.

If the @env{LC_ALL} environment variable is set, it overrides the value
of @env{LC_CTYPE} and @env{LC_MESSAGES}; otherwise, @env{LC_CTYPE}
and @env{LC_MESSAGES} default to the value of the @env{LANG}
environment variable.  If none of these variables are set, GCC
defaults to traditional C English behavior.

@item TMPDIR
@findex TMPDIR
If @env{TMPDIR} is set, it specifies the directory to use for temporary
files.  GCC uses temporary files to hold the output of one stage of
compilation which is to be used as input to the next stage: for example,
the output of the preprocessor, which is the input to the compiler
proper.

@item GCC_EXEC_PREFIX
@findex GCC_EXEC_PREFIX
If @env{GCC_EXEC_PREFIX} is set, it specifies a prefix to use in the
names of the subprograms executed by the compiler.  No slash is added
when this prefix is combined with the name of a subprogram, but you can
specify a prefix that ends with a slash if you wish.

If @env{GCC_EXEC_PREFIX} is not set, GCC will attempt to figure out
an appropriate prefix to use based on the pathname it was invoked with.

If GCC cannot find the subprogram using the specified prefix, it
tries looking in the usual places for the subprogram.

The default value of @env{GCC_EXEC_PREFIX} is
@file{@var{prefix}/lib/gcc-lib/} where @var{prefix} is the value
of @code{prefix} when you ran the @file{configure} script.

Other prefixes specified with @option{-B} take precedence over this prefix.

This prefix is also used for finding files such as @file{crt0.o} that are
used for linking.

In addition, the prefix is used in an unusual way in finding the
directories to search for header files.  For each of the standard
directories whose name normally begins with @samp{/usr/local/lib/gcc-lib}
(more precisely, with the value of @env{GCC_INCLUDE_DIR}), GCC tries
replacing that beginning with the specified prefix to produce an
alternate directory name.  Thus, with @option{-Bfoo/}, GCC will search
@file{foo/bar} where it would normally search @file{/usr/local/lib/bar}.
These alternate directories are searched first; the standard directories
come next.

@item COMPILER_PATH
@findex COMPILER_PATH
The value of @env{COMPILER_PATH} is a colon-separated list of
directories, much like @env{PATH}.  GCC tries the directories thus
specified when searching for subprograms, if it can't find the
subprograms using @env{GCC_EXEC_PREFIX}.

@item LIBRARY_PATH
@findex LIBRARY_PATH
The value of @env{LIBRARY_PATH} is a colon-separated list of
directories, much like @env{PATH}.  When configured as a native compiler,
GCC tries the directories thus specified when searching for special
linker files, if it can't find them using @env{GCC_EXEC_PREFIX}.  Linking
using GCC also uses these directories when searching for ordinary
libraries for the @option{-l} option (but directories specified with
@option{-L} come first).

@item LANG
@findex LANG
@cindex locale definition
This variable is used to pass locale information to the compiler.  One way in
which this information is used is to determine the character set to be used
when character literals, string literals and comments are parsed in C and C++.
When the compiler is configured to allow multibyte characters,
the following values for @env{LANG} are recognized:

@table @samp
@item C-JIS
Recognize JIS characters.
@item C-SJIS
Recognize SJIS characters.
@item C-EUCJP
Recognize EUCJP characters.
@end table

If @env{LANG} is not defined, or if it has some other value, then the
compiler will use mblen and mbtowc as defined by the default locale to
recognize and translate multibyte characters.
@end table

@noindent
Some additional environments variables affect the behavior of the
preprocessor.

@include cppenv.texi

@c man end

@node Precompiled Headers
@section Using Precompiled Headers
@cindex precompiled headers
@cindex speed of compilation

Often large projects have many header files that are included in every
source file.  The time the compiler takes to process these header files
over and over again can account for nearly all of the time required to
build the project.  To make builds faster, GCC allows users to
`precompile' a header file; then, if builds can use the precompiled
header file they will be much faster.

To create a precompiled header file, simply compile it as you would any
other file, if necessary using the @option{-x} option to make the driver
treat it as a C or C++ header file.  You will probably want to use a
tool like @command{make} to keep the precompiled header up-to-date when
the headers it contains change.

A precompiled header file will be searched for when @code{#include} is
seen in the compilation.  As it searches for the included file
(@pxref{Search Path,,Search Path,cpp.info,The C Preprocessor}) the
compiler looks for a precompiled header in each directory just before it
looks for the include file in that directory.  The name searched for is
the name specified in the @code{#include} with @samp{.gch} appended.  If
the precompiled header file can't be used, it is ignored.

For instance, if you have @code{#include "all.h"}, and you have
@file{all.h.gch} in the same directory as @file{all.h}, then the
precompiled header file will be used if possible, and the original
header will be used otherwise.

Alternatively, you might decide to put the precompiled header file in a
directory and use @option{-I} to ensure that directory is searched
before (or instead of) the directory containing the original header.
Then, if you want to check that the precompiled header file is always
used, you can put a file of the same name as the original header in this
directory containing an @code{#error} command.

This also works with @option{-include}.  So yet another way to use
precompiled headers, good for projects not designed with precompiled
header files in mind, is to simply take most of the header files used by
a project, include them from another header file, precompile that header
file, and @option{-include} the precompiled header.  If the header files
have guards against multiple inclusion, they will be skipped because
they've already been included (in the precompiled header).

If you need to precompile the same header file for different
languages, targets, or compiler options, you can instead make a
@emph{directory} named like @file{all.h.gch}, and put each precompiled
header in the directory.  (It doesn't matter what you call the files
in the directory, every precompiled header in the directory will be
considered.)  The first precompiled header encountered in the
directory that is valid for this compilation will be used; they're
searched in no particular order.

There are many other possibilities, limited only by your imagination,
good sense, and the constraints of your build system.

A precompiled header file can be used only when these conditions apply:

@itemize
@item
Only one precompiled header can be used in a particular compilation.
@item
A precompiled header can't be used once the first C token is seen.  You
can have preprocessor directives before a precompiled header; you can
even include a precompiled header from inside another header, so long as
there are no C tokens before the @code{#include}.
@item
The precompiled header file must be produced for the same language as
the current compilation.  You can't use a C precompiled header for a C++
compilation.
@item
The precompiled header file must be produced by the same compiler
version and configuration as the current compilation is using.
The easiest way to guarantee this is to use the same compiler binary
for creating and using precompiled headers.
@item
Any macros defined before the precompiled header (including with
@option{-D}) must either be defined in the same way as when the
precompiled header was generated, or must not affect the precompiled
header, which usually means that the they don't appear in the
precompiled header at all.
@item
Certain command-line options must be defined in the same way as when the
precompiled header was generated.  At present, it's not clear which
options are safe to change and which are not; the safest choice is to
use exactly the same options when generating and using the precompiled
header.
@end itemize

For all of these but the last, the compiler will automatically ignore
the precompiled header if the conditions aren't met.  For the last item,
some option changes will cause the precompiled header to be rejected,
but not all incompatible option combinations have yet been found.  If
you find a new incompatible combination, please consider filing a bug
report, see @ref{Bugs}.

@node Running Protoize
@section Running Protoize

The program @code{protoize} is an optional part of GCC@.  You can use
it to add prototypes to a program, thus converting the program to ISO
C in one respect.  The companion program @code{unprotoize} does the
reverse: it removes argument types from any prototypes that are found.

When you run these programs, you must specify a set of source files as
command line arguments.  The conversion programs start out by compiling
these files to see what functions they define.  The information gathered
about a file @var{foo} is saved in a file named @file{@var{foo}.X}.

After scanning comes actual conversion.  The specified files are all
eligible to be converted; any files they include (whether sources or
just headers) are eligible as well.

But not all the eligible files are converted.  By default,
@code{protoize} and @code{unprotoize} convert only source and header
files in the current directory.  You can specify additional directories
whose files should be converted with the @option{-d @var{directory}}
option.  You can also specify particular files to exclude with the
@option{-x @var{file}} option.  A file is converted if it is eligible, its
directory name matches one of the specified directory names, and its
name within the directory has not been excluded.

Basic conversion with @code{protoize} consists of rewriting most
function definitions and function declarations to specify the types of
the arguments.  The only ones not rewritten are those for varargs
functions.

@code{protoize} optionally inserts prototype declarations at the
beginning of the source file, to make them available for any calls that
precede the function's definition.  Or it can insert prototype
declarations with block scope in the blocks where undeclared functions
are called.

Basic conversion with @code{unprotoize} consists of rewriting most
function declarations to remove any argument types, and rewriting
function definitions to the old-style pre-ISO form.

Both conversion programs print a warning for any function declaration or
definition that they can't convert.  You can suppress these warnings
with @option{-q}.

The output from @code{protoize} or @code{unprotoize} replaces the
original source file.  The original file is renamed to a name ending
with @samp{.save} (for DOS, the saved filename ends in @samp{.sav}
without the original @samp{.c} suffix).  If the @samp{.save} (@samp{.sav}
for DOS) file already exists, then the source file is simply discarded.

@code{protoize} and @code{unprotoize} both depend on GCC itself to
scan the program and collect information about the functions it uses.
So neither of these programs will work until GCC is installed.

Here is a table of the options you can use with @code{protoize} and
@code{unprotoize}.  Each option works with both programs unless
otherwise stated.

@table @code
@item -B @var{directory}
Look for the file @file{SYSCALLS.c.X} in @var{directory}, instead of the
usual directory (normally @file{/usr/local/lib}).  This file contains
prototype information about standard system functions.  This option
applies only to @code{protoize}.

@item -c @var{compilation-options}
Use @var{compilation-options} as the options when running @command{gcc} to
produce the @samp{.X} files.  The special option @option{-aux-info} is
always passed in addition, to tell @command{gcc} to write a @samp{.X} file.

Note that the compilation options must be given as a single argument to
@code{protoize} or @code{unprotoize}.  If you want to specify several
@command{gcc} options, you must quote the entire set of compilation options
to make them a single word in the shell.

There are certain @command{gcc} arguments that you cannot use, because they
would produce the wrong kind of output.  These include @option{-g},
@option{-O}, @option{-c}, @option{-S}, and @option{-o} If you include these in
the @var{compilation-options}, they are ignored.

@item -C
Rename files to end in @samp{.C} (@samp{.cc} for DOS-based file
systems) instead of @samp{.c}.  This is convenient if you are converting
a C program to C++.  This option applies only to @code{protoize}.

@item -g
Add explicit global declarations.  This means inserting explicit
declarations at the beginning of each source file for each function
that is called in the file and was not declared.  These declarations
precede the first function definition that contains a call to an
undeclared function.  This option applies only to @code{protoize}.

@item -i @var{string}
Indent old-style parameter declarations with the string @var{string}.
This option applies only to @code{protoize}.

@code{unprotoize} converts prototyped function definitions to old-style
function definitions, where the arguments are declared between the
argument list and the initial @samp{@{}.  By default, @code{unprotoize}
uses five spaces as the indentation.  If you want to indent with just
one space instead, use @option{-i " "}.

@item -k
Keep the @samp{.X} files.  Normally, they are deleted after conversion
is finished.

@item -l
Add explicit local declarations.  @code{protoize} with @option{-l} inserts
a prototype declaration for each function in each block which calls the
function without any declaration.  This option applies only to
@code{protoize}.

@item -n
Make no real changes.  This mode just prints information about the conversions
that would have been done without @option{-n}.

@item -N
Make no @samp{.save} files.  The original files are simply deleted.
Use this option with caution.

@item -p @var{program}
Use the program @var{program} as the compiler.  Normally, the name
@file{gcc} is used.

@item -q
Work quietly.  Most warnings are suppressed.

@item -v
Print the version number, just like @option{-v} for @command{gcc}.
@end table

If you need special compiler options to compile one of your program's
source files, then you should generate that file's @samp{.X} file
specially, by running @command{gcc} on that source file with the
appropriate options and the option @option{-aux-info}.  Then run
@code{protoize} on the entire set of files.  @code{protoize} will use
the existing @samp{.X} file because it is newer than the source file.
For example:

@example
gcc -Dfoo=bar file1.c -aux-info file1.X
protoize *.c
@end example

@noindent
You need to include the special files along with the rest in the
@code{protoize} command, even though their @samp{.X} files already
exist, because otherwise they won't get converted.

@xref{Protoize Caveats}, for more information on how to use
@code{protoize} successfully.