/* Definitions of target machine for GNU compiler, for IBM RS/6000.
Copyright (C) 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999,
- 2000, 2001, 2002, 2003, 2004, 2005 Free Software Foundation, Inc.
+ 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007
+ Free Software Foundation, Inc.
Contributed by Richard Kenner (kenner@vlsi1.ultra.nyu.edu)
This file is part of GCC.
%{mno-power: %{!mpowerpc*: -mcom}} \
%{!mno-power: %{!mpower*: %(asm_default)}}} \
%{mcpu=common: -mcom} \
+%{mcpu=cell: -mcell} \
%{mcpu=power: -mpwr} \
%{mcpu=power2: -mpwrx} \
%{mcpu=power3: -mppc64} \
%{mcpu=power4: -mpower4} \
%{mcpu=power5: -mpower4} \
%{mcpu=power5+: -mpower4} \
+%{mcpu=power6: -mpower4 -maltivec} \
+%{mcpu=power6x: -mpower4 -maltivec} \
%{mcpu=powerpc: -mppc} \
%{mcpu=rios: -mpwr} \
%{mcpu=rios1: -mpwr} \
#define TARGET_FPRND 0
#endif
+/* Define TARGET_CMPB if the target assembler does not support the
+ cmpb instruction. */
+
+#ifndef HAVE_AS_CMPB
+#undef TARGET_CMPB
+#define TARGET_CMPB 0
+#endif
+
+/* Define TARGET_MFPGPR if the target assembler does not support the
+ mffpr and mftgpr instructions. */
+
+#ifndef HAVE_AS_MFPGPR
+#undef TARGET_MFPGPR
+#define TARGET_MFPGPR 0
+#endif
+
+/* Define TARGET_DFP if the target assembler does not support decimal
+ floating point instructions. */
+#ifndef HAVE_AS_DFP
+#undef TARGET_DFP
+#define TARGET_DFP 0
+#endif
+
#ifndef TARGET_SECURE_PLT
#define TARGET_SECURE_PLT 0
#endif
#ifdef IN_LIBGCC2
/* For libgcc2 we make sure this is a compile time constant */
-#if defined (__64BIT__) || defined (__powerpc64__)
+#if defined (__64BIT__) || defined (__powerpc64__) || defined (__ppc64__)
#undef TARGET_POWERPC64
#define TARGET_POWERPC64 1
#else
PROCESSOR_PPC7450,
PROCESSOR_PPC8540,
PROCESSOR_POWER4,
- PROCESSOR_POWER5
+ PROCESSOR_POWER5,
+ PROCESSOR_POWER6,
+ PROCESSOR_CELL
};
extern enum processor_type rs6000_cpu;
/* These are separate from target_flags because we've run out of bits
there. */
extern int rs6000_long_double_type_size;
+extern int rs6000_ieeequad;
extern int rs6000_altivec_abi;
extern int rs6000_spe_abi;
extern int rs6000_float_gprs;
#endif
#define TARGET_LONG_DOUBLE_128 (rs6000_long_double_type_size == 128)
+#define TARGET_IEEEQUAD rs6000_ieeequad
#define TARGET_ALTIVEC_ABI rs6000_altivec_abi
#define TARGET_SPE_ABI 0
#define TARGET_FPRS 1
#define TARGET_E500_SINGLE 0
#define TARGET_E500_DOUBLE 0
+#define CHECK_E500_OPTIONS do { } while (0)
+
+/* E500 processors only support plain "sync", not lwsync. */
+#define TARGET_NO_LWSYNC TARGET_E500
/* Sometimes certain combinations of command options do not make sense
on a particular target machine. You can define a macro
#define LOCAL_ALIGNMENT(TYPE, ALIGN) \
((TARGET_ALTIVEC && TREE_CODE (TYPE) == VECTOR_TYPE) ? 128 : \
(TARGET_E500_DOUBLE && TYPE_MODE (TYPE) == DFmode) ? 64 : \
- (TARGET_SPE && TREE_CODE (TYPE) == VECTOR_TYPE) ? 64 : ALIGN)
+ (TARGET_SPE && TREE_CODE (TYPE) == VECTOR_TYPE \
+ && SPE_VECTOR_MODE (TYPE_MODE (TYPE))) ? 64 : ALIGN)
/* Alignment of field after `int : 0' in a structure. */
#define EMPTY_FIELD_BOUNDARY 32
#define SLOW_UNALIGNED_ACCESS(MODE, ALIGN) \
(STRICT_ALIGNMENT \
|| (((MODE) == SFmode || (MODE) == DFmode || (MODE) == TFmode \
+ || (MODE) == DDmode || (MODE) == TDmode \
|| (MODE) == DImode) \
&& (ALIGN) < 32))
\f
#define DWARF_REG_TO_UNWIND_COLUMN(r) \
((r) > 1200 ? ((r) - 1200 + FIRST_PSEUDO_REGISTER - 1) : (r))
+/* Use standard DWARF numbering for DWARF debugging information. */
+#define DBX_REGISTER_NUMBER(REGNO) rs6000_dbx_register_number (REGNO)
+
/* Use gcc hard register numbering for eh_frame. */
#define DWARF_FRAME_REGNUM(REGNO) (REGNO)
+/* Map register numbers held in the call frame info that gcc has
+ collected using DWARF_FRAME_REGNUM to those that should be output in
+ .debug_frame and .eh_frame. We continue to use gcc hard reg numbers
+ for .eh_frame, but use the numbers mandated by the various ABIs for
+ .debug_frame. rs6000_emit_prologue has translated any combination of
+ CR2, CR3, CR4 saves to a save of CR2. The actual code emitted saves
+ the whole of CR, so we map CR2_REGNO to the DWARF reg for CR. */
+#define DWARF2_FRAME_REG_OUT(REGNO, FOR_EH) \
+ ((FOR_EH) ? (REGNO) \
+ : (REGNO) == CR2_REGNO ? 64 \
+ : DBX_REGISTER_NUMBER (REGNO))
+
/* 1 for registers that have pervasive standard uses
and are not available for the register allocator.
, 0, 0, 0 \
}
-#define MQ_REGNO 64
-#define CR0_REGNO 68
-#define CR1_REGNO 69
-#define CR2_REGNO 70
-#define CR3_REGNO 71
-#define CR4_REGNO 72
-#define MAX_CR_REGNO 75
-#define XER_REGNO 76
-#define FIRST_ALTIVEC_REGNO 77
-#define LAST_ALTIVEC_REGNO 108
#define TOTAL_ALTIVEC_REGS (LAST_ALTIVEC_REGNO - FIRST_ALTIVEC_REGNO + 1)
-#define VRSAVE_REGNO 109
-#define VSCR_REGNO 110
-#define SPE_ACC_REGNO 111
-#define SPEFSCR_REGNO 112
#define FIRST_SAVED_ALTIVEC_REGNO (FIRST_ALTIVEC_REGNO+20)
#define FIRST_SAVED_FP_REGNO (14+32)
#define FP_REGNO_P(N) ((N) >= 32 && (N) <= 63)
/* True if register is a condition register. */
-#define CR_REGNO_P(N) ((N) >= 68 && (N) <= 75)
+#define CR_REGNO_P(N) ((N) >= CR0_REGNO && (N) <= CR7_REGNO)
/* True if register is a condition register, but not cr0. */
-#define CR_REGNO_NOT_CR0_P(N) ((N) >= 69 && (N) <= 75)
+#define CR_REGNO_NOT_CR0_P(N) ((N) >= CR1_REGNO && (N) <= CR7_REGNO)
/* True if register is an integer register. */
#define INT_REGNO_P(N) \
If HARD_REGNO_MODE_OK could produce different values for MODE1 and MODE2,
for any hard reg, then this must be 0 for correct output. */
#define MODES_TIEABLE_P(MODE1, MODE2) \
- (GET_MODE_CLASS (MODE1) == MODE_FLOAT \
- ? GET_MODE_CLASS (MODE2) == MODE_FLOAT \
- : GET_MODE_CLASS (MODE2) == MODE_FLOAT \
- ? GET_MODE_CLASS (MODE1) == MODE_FLOAT \
+ (SCALAR_FLOAT_MODE_P (MODE1) \
+ ? SCALAR_FLOAT_MODE_P (MODE2) \
+ : SCALAR_FLOAT_MODE_P (MODE2) \
+ ? SCALAR_FLOAT_MODE_P (MODE1) \
: GET_MODE_CLASS (MODE1) == MODE_CC \
? GET_MODE_CLASS (MODE2) == MODE_CC \
: GET_MODE_CLASS (MODE2) == MODE_CC \
emitted the vrsave mask. */
#define HARD_REGNO_RENAME_OK(SRC, DST) \
- (! ALTIVEC_REGNO_P (DST) || regs_ever_live[DST])
+ (! ALTIVEC_REGNO_P (DST) || df_regs_ever_live_p (DST))
/* A C expression returning the cost of moving data from a register of class
CLASS1 to one of CLASS2. */
#define LOGICAL_OP_NON_SHORT_CIRCUIT 0
-/* A fixed register used at prologue and epilogue generation to fix
- addressing modes. The SPE needs heavy addressing fixes at the last
- minute, and it's best to save a register for it.
-
- AltiVec also needs fixes, but we've gotten around using r11, which
- is actually wrong because when use_backchain_to_restore_sp is true,
- we end up clobbering r11.
+/* A fixed register used at epilogue generation to address SPE registers
+ with negative offsets. The 64-bit load/store instructions on the SPE
+ only take positive offsets (and small ones at that), so we need to
+ reserve a register for consing up negative offsets. */
- The AltiVec case needs to be fixed. Dunno if we should break ABI
- compatibility and reserve a register for it as well.. */
-
-#define FIXED_SCRATCH (TARGET_SPE ? 14 : 11)
+#define FIXED_SCRATCH 0
/* Define this macro to change register usage conditional on target
flags. */
/* Place to put static chain when calling a function that requires it. */
#define STATIC_CHAIN_REGNUM 11
-/* Link register number. */
-#define LINK_REGISTER_REGNUM 65
-
-/* Count register number. */
-#define COUNT_REGISTER_REGNUM 66
\f
/* Define the classes of registers for register constraints in the
machine description. Also define ranges of constants.
{ 0xffffffff, 0x00000000, 0x0000000f, 0x00022000 }, /* SPEC_OR_GEN_REGS */ \
{ 0x00000000, 0x00000000, 0x00000010, 0x00000000 }, /* CR0_REGS */ \
{ 0x00000000, 0x00000000, 0x00000ff0, 0x00000000 }, /* CR_REGS */ \
- { 0xffffffff, 0x00000000, 0x0000efff, 0x00000000 }, /* NON_FLOAT_REGS */ \
+ { 0xffffffff, 0x00000000, 0x0000efff, 0x00020000 }, /* NON_FLOAT_REGS */ \
{ 0x00000000, 0x00000000, 0x00001000, 0x00000000 }, /* XER_REGS */ \
{ 0xffffffff, 0xffffffff, 0xffffffff, 0x0003ffff } /* ALL_REGS */ \
}
: (REGNO) == CR0_REGNO ? CR0_REGS \
: CR_REGNO_P (REGNO) ? CR_REGS \
: (REGNO) == MQ_REGNO ? MQ_REGS \
- : (REGNO) == LINK_REGISTER_REGNUM ? LINK_REGS \
- : (REGNO) == COUNT_REGISTER_REGNUM ? CTR_REGS \
+ : (REGNO) == LR_REGNO ? LINK_REGS \
+ : (REGNO) == CTR_REGNO ? CTR_REGS \
: (REGNO) == ARG_POINTER_REGNUM ? BASE_REGS \
: (REGNO) == XER_REGNO ? XER_REGS \
: (REGNO) == VRSAVE_REGNO ? VRSAVE_REGS \
#define INDEX_REG_CLASS GENERAL_REGS
#define BASE_REG_CLASS BASE_REGS
-/* Get reg_class from a letter such as appears in the machine description. */
-
-#define REG_CLASS_FROM_LETTER(C) \
- ((C) == 'f' ? ((TARGET_HARD_FLOAT && TARGET_FPRS) ? FLOAT_REGS : NO_REGS) \
- : (C) == 'b' ? BASE_REGS \
- : (C) == 'h' ? SPECIAL_REGS \
- : (C) == 'q' ? MQ_REGS \
- : (C) == 'c' ? CTR_REGS \
- : (C) == 'l' ? LINK_REGS \
- : (C) == 'v' ? ALTIVEC_REGS \
- : (C) == 'x' ? CR0_REGS \
- : (C) == 'y' ? CR_REGS \
- : (C) == 'z' ? XER_REGS \
- : NO_REGS)
-
-/* The letters I, J, K, L, M, N, and P in a register constraint string
- can be used to stand for particular ranges of immediate operands.
- This macro defines what the ranges are.
- C is the letter, and VALUE is a constant value.
- Return 1 if VALUE is in the range specified by C.
-
- `I' is a signed 16-bit constant
- `J' is a constant with only the high-order 16 bits nonzero
- `K' is a constant with only the low-order 16 bits nonzero
- `L' is a signed 16-bit constant shifted left 16 bits
- `M' is a constant that is greater than 31
- `N' is a positive constant that is an exact power of two
- `O' is the constant zero
- `P' is a constant whose negation is a signed 16-bit constant */
-
-#define CONST_OK_FOR_LETTER_P(VALUE, C) \
- ( (C) == 'I' ? (unsigned HOST_WIDE_INT) ((VALUE) + 0x8000) < 0x10000 \
- : (C) == 'J' ? ((VALUE) & (~ (unsigned HOST_WIDE_INT) 0xffff0000)) == 0 \
- : (C) == 'K' ? ((VALUE) & (~ (HOST_WIDE_INT) 0xffff)) == 0 \
- : (C) == 'L' ? (((VALUE) & 0xffff) == 0 \
- && ((VALUE) >> 31 == -1 || (VALUE) >> 31 == 0)) \
- : (C) == 'M' ? (VALUE) > 31 \
- : (C) == 'N' ? (VALUE) > 0 && exact_log2 (VALUE) >= 0 \
- : (C) == 'O' ? (VALUE) == 0 \
- : (C) == 'P' ? (unsigned HOST_WIDE_INT) ((- (VALUE)) + 0x8000) < 0x10000 \
- : 0)
-
-/* Similar, but for floating constants, and defining letters G and H.
- Here VALUE is the CONST_DOUBLE rtx itself.
-
- We flag for special constants when we can copy the constant into
- a general register in two insns for DF/DI and one insn for SF.
-
- 'H' is used for DI/DF constants that take 3 insns. */
-
-#define CONST_DOUBLE_OK_FOR_LETTER_P(VALUE, C) \
- ( (C) == 'G' ? (num_insns_constant (VALUE, GET_MODE (VALUE)) \
- == ((GET_MODE (VALUE) == SFmode) ? 1 : 2)) \
- : (C) == 'H' ? (num_insns_constant (VALUE, GET_MODE (VALUE)) == 3) \
- : 0)
-
-/* Optional extra constraints for this machine.
-
- 'Q' means that is a memory operand that is just an offset from a reg.
- 'R' is for AIX TOC entries.
- 'S' is a constant that can be placed into a 64-bit mask operand.
- 'T' is a constant that can be placed into a 32-bit mask operand.
- 'U' is for V.4 small data references.
- 'W' is a vector constant that can be easily generated (no mem refs).
- 'Y' is an indexed or word-aligned displacement memory operand.
- 'Z' is an indexed or indirect memory operand.
- 'a' is an indexed or indirect address operand.
- 't' is for AND masks that can be performed by two rldic{l,r} insns
- (but excluding those that could match other constraints of anddi3.) */
-
-#define EXTRA_CONSTRAINT(OP, C) \
- ((C) == 'Q' ? GET_CODE (OP) == MEM && GET_CODE (XEXP (OP, 0)) == REG \
- : (C) == 'R' ? legitimate_constant_pool_address_p (OP) \
- : (C) == 'S' ? mask64_operand (OP, DImode) \
- : (C) == 'T' ? mask_operand (OP, GET_MODE (OP)) \
- : (C) == 'U' ? (DEFAULT_ABI == ABI_V4 \
- && small_data_operand (OP, GET_MODE (OP))) \
- : (C) == 't' ? (mask64_2_operand (OP, DImode) \
- && (fixed_regs[CR0_REGNO] \
- || !logical_operand (OP, DImode)) \
- && !mask_operand (OP, DImode) \
- && !mask64_operand (OP, DImode)) \
- : (C) == 'W' ? (easy_vector_constant (OP, GET_MODE (OP))) \
- : (C) == 'Y' ? (word_offset_memref_operand (OP, GET_MODE (OP))) \
- : (C) == 'Z' ? (indexed_or_indirect_operand (OP, GET_MODE (OP))) \
- : (C) == 'a' ? (indexed_or_indirect_address (OP, GET_MODE (OP))) \
- : 0)
-
-/* Define which constraints are memory constraints. Tell reload
- that any memory address can be reloaded by copying the
- memory address into a base register if required. */
-
-#define EXTRA_MEMORY_CONSTRAINT(C, STR) \
- ((C) == 'Q' || (C) == 'Y' || (C) == 'Z')
-
-/* Define which constraints should be treated like address constraints
- by the reload pass. */
-
-#define EXTRA_ADDRESS_CONSTRAINT(C, STR) \
- ((C) == 'a')
-
/* Given an rtx X being reloaded into a reg required to be
in class CLASS, return the class of reg to actually use.
In general this is just CLASS; but on some machines
NO_REGS is returned. */
#define SECONDARY_RELOAD_CLASS(CLASS,MODE,IN) \
- secondary_reload_class (CLASS, MODE, IN)
+ rs6000_secondary_reload_class (CLASS, MODE, IN)
/* If we are copying between FP or AltiVec registers and anything
- else, we need a memory location. */
-
-#define SECONDARY_MEMORY_NEEDED(CLASS1,CLASS2,MODE) \
- ((CLASS1) != (CLASS2) && ((CLASS1) == FLOAT_REGS \
- || (CLASS2) == FLOAT_REGS \
- || (CLASS1) == ALTIVEC_REGS \
+ else, we need a memory location. The exception is when we are
+ targeting ppc64 and the move to/from fpr to gpr instructions
+ are available.*/
+
+#define SECONDARY_MEMORY_NEEDED(CLASS1,CLASS2,MODE) \
+ ((CLASS1) != (CLASS2) && (((CLASS1) == FLOAT_REGS \
+ && (!TARGET_MFPGPR || !TARGET_POWERPC64 \
+ || ((MODE != DFmode) \
+ && (MODE != DDmode) \
+ && (MODE != DImode)))) \
+ || ((CLASS2) == FLOAT_REGS \
+ && (!TARGET_MFPGPR || !TARGET_POWERPC64 \
+ || ((MODE != DFmode) \
+ && (MODE != DDmode) \
+ && (MODE != DImode)))) \
+ || (CLASS1) == ALTIVEC_REGS \
|| (CLASS2) == ALTIVEC_REGS))
/* Return the maximum number of consecutive registers
? 1 \
: ((GET_MODE_SIZE (MODE) + UNITS_PER_WORD - 1) / UNITS_PER_WORD))
-
-/* Return a class of registers that cannot change FROM mode to TO mode. */
-
-#define CANNOT_CHANGE_MODE_CLASS(FROM, TO, CLASS) \
- (((DEFAULT_ABI == ABI_AIX || DEFAULT_ABI == ABI_DARWIN) \
- && GET_MODE_SIZE (FROM) >= 8 && GET_MODE_SIZE (TO) >= 8) \
- ? 0 \
- : GET_MODE_SIZE (FROM) != GET_MODE_SIZE (TO) \
- ? reg_classes_intersect_p (FLOAT_REGS, CLASS) \
- : (TARGET_E500_DOUBLE && (((TO) == DFmode) + ((FROM) == DFmode)) == 1) \
- ? reg_classes_intersect_p (GENERAL_REGS, CLASS) \
- : (TARGET_E500_DOUBLE && (((TO) == DImode) + ((FROM) == DImode)) == 1) \
- ? reg_classes_intersect_p (GENERAL_REGS, CLASS) \
- : (TARGET_SPE && (SPE_VECTOR_MODE (FROM) + SPE_VECTOR_MODE (TO)) == 1) \
- ? reg_classes_intersect_p (GENERAL_REGS, CLASS) \
- : 0)
+/* Return nonzero if for CLASS a mode change from FROM to TO is invalid. */
+
+#define CANNOT_CHANGE_MODE_CLASS(FROM, TO, CLASS) \
+ (GET_MODE_SIZE (FROM) != GET_MODE_SIZE (TO) \
+ ? ((GET_MODE_SIZE (FROM) < 8 || GET_MODE_SIZE (TO) < 8 \
+ || TARGET_IEEEQUAD) \
+ && reg_classes_intersect_p (FLOAT_REGS, CLASS)) \
+ : (((TARGET_E500_DOUBLE \
+ && ((((TO) == DFmode) + ((FROM) == DFmode)) == 1 \
+ || (((TO) == TFmode) + ((FROM) == TFmode)) == 1 \
+ || (((TO) == DImode) + ((FROM) == DImode)) == 1)) \
+ || (TARGET_SPE \
+ && (SPE_VECTOR_MODE (FROM) + SPE_VECTOR_MODE (TO)) == 1)) \
+ && reg_classes_intersect_p (GENERAL_REGS, CLASS)))
/* Stack layout; function entry, exit and calling. */
/* Define this if the above stack space is to be considered part of the
space allocated by the caller. */
-#define OUTGOING_REG_PARM_STACK_SPACE
+#define OUTGOING_REG_PARM_STACK_SPACE 1
/* This is the difference between the logical top of stack and the actual sp.
needed. */
#define EPILOGUE_USES(REGNO) \
- ((reload_completed && (REGNO) == LINK_REGISTER_REGNUM) \
+ ((reload_completed && (REGNO) == LR_REGNO) \
|| (TARGET_ALTIVEC && (REGNO) == VRSAVE_REGNO) \
|| (current_function_calls_eh_return \
&& TARGET_AIX \
#define HAVE_PRE_DECREMENT 1
#define HAVE_PRE_INCREMENT 1
+#define HAVE_PRE_MODIFY_DISP 1
+#define HAVE_PRE_MODIFY_REG 1
/* Macros to check register numbers against specific register classes. */
#define EASY_VECTOR_15(n) ((n) >= -16 && (n) <= 15)
#define EASY_VECTOR_15_ADD_SELF(n) (!EASY_VECTOR_15((n)) \
- && EASY_VECTOR_15((n) >> 1))
+ && EASY_VECTOR_15((n) >> 1) \
+ && ((n) & 1) == 0)
/* The macros REG_OK_FOR..._P assume that the arg is a REG rtx
and check its validity for a certain class.
/* Nonzero if X is a hard reg that can be used as an index
or if it is a pseudo reg in the non-strict case. */
#define INT_REG_OK_FOR_INDEX_P(X, STRICT) \
- ((! (STRICT) \
- && (REGNO (X) <= 31 \
- || REGNO (X) == ARG_POINTER_REGNUM \
- || REGNO (X) == FRAME_POINTER_REGNUM \
- || REGNO (X) >= FIRST_PSEUDO_REGISTER)) \
- || ((STRICT) && REGNO_OK_FOR_INDEX_P (REGNO (X))))
+ ((!(STRICT) && REGNO (X) >= FIRST_PSEUDO_REGISTER) \
+ || REGNO_OK_FOR_INDEX_P (REGNO (X)))
/* Nonzero if X is a hard reg that can be used as a base reg
or if it is a pseudo reg in the non-strict case. */
#define INT_REG_OK_FOR_BASE_P(X, STRICT) \
- (REGNO (X) > 0 && INT_REG_OK_FOR_INDEX_P (X, (STRICT)))
+ ((!(STRICT) && REGNO (X) >= FIRST_PSEUDO_REGISTER) \
+ || REGNO_OK_FOR_BASE_P (REGNO (X)))
#define REG_OK_FOR_INDEX_P(X) INT_REG_OK_FOR_INDEX_P (X, REG_OK_STRICT_FLAG)
#define REG_OK_FOR_BASE_P(X) INT_REG_OK_FOR_BASE_P (X, REG_OK_STRICT_FLAG)
The MODE argument is the machine mode for the MEM expression
that wants to use this address.
- On the RS/6000, there are four valid address: a SYMBOL_REF that
+ On the RS/6000, there are four valid addresses: a SYMBOL_REF that
refers to a constant pool entry of an address (or the sum of it
plus a constant), a short (16-bit signed) constant plus a register,
the sum of two registers, or a register indirect, possibly with an
comparison. CCmode should be used in all other cases. */
#define SELECT_CC_MODE(OP,X,Y) \
- (GET_MODE_CLASS (GET_MODE (X)) == MODE_FLOAT ? CCFPmode \
+ (SCALAR_FLOAT_MODE_P (GET_MODE (X)) ? CCFPmode \
: (OP) == GTU || (OP) == LTU || (OP) == GEU || (OP) == LEU ? CCUNSmode \
: (((OP) == EQ || (OP) == NE) && COMPARISON_P (X) \
? CCEQmode : CCmode))
while (0)
#endif
+#if HAVE_GAS_WEAKREF
+#define ASM_OUTPUT_WEAKREF(FILE, DECL, NAME, VALUE) \
+ do \
+ { \
+ fputs ("\t.weakref\t", (FILE)); \
+ RS6000_OUTPUT_BASENAME ((FILE), (NAME)); \
+ fputs (", ", (FILE)); \
+ RS6000_OUTPUT_BASENAME ((FILE), (VALUE)); \
+ if ((DECL) && TREE_CODE (DECL) == FUNCTION_DECL \
+ && DEFAULT_ABI == ABI_AIX && DOT_SYMBOLS) \
+ { \
+ fputs ("\n\t.weakref\t.", (FILE)); \
+ RS6000_OUTPUT_BASENAME ((FILE), (NAME)); \
+ fputs (", .", (FILE)); \
+ RS6000_OUTPUT_BASENAME ((FILE), (VALUE)); \
+ } \
+ fputc ('\n', (FILE)); \
+ } while (0)
+#endif
+
/* This implements the `alias' attribute. */
#undef ASM_OUTPUT_DEF_FROM_DECLS
#define ASM_OUTPUT_DEF_FROM_DECLS(FILE, DECL, TARGET) \
dwarf2 unwind information. This also enables the table driven
mechanism. */
-#define INCOMING_RETURN_ADDR_RTX gen_rtx_REG (Pmode, LINK_REGISTER_REGNUM)
-#define DWARF_FRAME_RETURN_COLUMN DWARF_FRAME_REGNUM (LINK_REGISTER_REGNUM)
+#define INCOMING_RETURN_ADDR_RTX gen_rtx_REG (Pmode, LR_REGNO)
+#define DWARF_FRAME_RETURN_COLUMN DWARF_FRAME_REGNUM (LR_REGNO)
/* Describe how we implement __builtin_eh_return. */
#define EH_RETURN_DATA_REGNO(N) ((N) < 4 ? (N) + 3 : INVALID_REGNUM)
OSDN Git Service
